Question about 1997 Ford Probe

1 Answer

How to set timing on 97 ford probe gt

H ow to set timing on 97 ford probe gt
timing light used,distruber adjestment made. timing mark did not move.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,984 Answers

This is the specs...not too sure on what else you are asking about:

how to set timing on 97 ford probe gt - d23bf61.gif
Save to desktop and then zoom.

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

89 ford probe hesitates when leaving a red light, then runs fine otherwise, fuel filter?


Engine Runs Rough, Stalls, Hesitates on Acceleration, Hard ...

repairpal.com > Problems > Ford > Probe
Ford Probe Engine Runs Rough, Stalls, Hesitates on Acceleration, Hard Starting, Poor Performance. This is a verified problem based on 9 reports. Learn more ...

Starting Problems - 1997 Ford Probe - RepairPal

repairpal.com > Questions > Ford > Probe > 1997 Ford Probe
Dec 5, 2010 - Starting Problems on 1997 Ford Probe ... If the engine runs rough,stalls, hesitates on acceleration, is hard to start, or has generally poor ...

A new misfire/hesitation on accel. Problem.. - ProbeTalk.com Forums

forums.probetalk.com > Tech Section > 2nd Gen (93-97) V6 2.5L

Feb 05, 2016 | Ford Cars & Trucks

1 Answer

Caint see timing marks on 93 ford probe v6 gt


There is some very wrong information here. Do not remove the cap or mess with the rotor! As someone else said, go to probetalk.com jumper the t/en test point to ground to disable the automatic timing adjustment - after that it's pretty standard procedure.

Sep 15, 2011 | 1993 Ford Probe

1 Answer

Where is computer for key less entry located for 97 ford probe gt


on right rear quarter panel, behind trim panel

Mar 17, 2011 | 1997 Ford Probe

1 Answer

I need timing belt digrams for a 94 ford probe gt has a 6 cylindar engine


moz-screenshot-1.pngAlign the engine timing marks as follows, then install the belt.

ae00695.gif

f446780.gif
Once the belt is routed, as shown below, install the indicated pulley last, then pull the pin out of the hydrualic-tensioner.
cc4ecb7.gif

May 20, 2010 | 1994 Ford Probe

2 Answers

Firing order and timing for 292 ford


The firing order is 1-5-4-8-6-3-7-2, distributor turns counter-clockwise. The ignition timing can be set using marks on the vibration damper. The wide mark is TDC (Top Dead Center), each mark after the wide mark represents 2, 4, 6, 8 and 10 degrees before TDC. Set timing 3 degrees BTDC (Before Top Dead Center). In addition, valve timingis set like this: Intake opens: 12 degrees BTDC
Exhaust Closes: 8 degrees ATDC

Feb 04, 2010 | 1981 Ford F 100

2 Answers

How do you replace a distributor assembly on a 1995 Ford Probe GT


Careful!
There is one bolt and clamp at the bottom of the distributor shaft.
You MUST make a mark on the shaft AND the engine so that when you put another one in, you can line it up correctly.
Otherwise, your spark timing will be off & may not run.
When removing you may have to twist the assembly as you remove it (that's normal).
Oh,, yeah... don't remove the spark plug wires at the distributor .. until you really have to... mark them well (masking tape or whatever technique you use).

Sep 01, 2009 | 1995 Ford Probe

1 Answer

Timing marks


you should have timming marks on the front engine block. if you see it you will need a timming light to set it very cheap to buy. if you do not see any timming marks and you have a distributer losen it a little but with the car running. now with the car running turn the distruber left or right until you hear and feel the car idle high. once you feel it idle low go back up until it idle high and keep it there and tighten the distruber back. turn the car off and try starting it back up. it should start right on time with the correct timming and idle. good luck

Jul 08, 2009 | 1995 Chevrolet Monte Carlo

1 Answer

How do you set the timing marks on 97 ford probe?


what marks are used when setting timing on 1997 ford probe

Oct 19, 2008 | 1997 Ford Probe

Not finding what you are looking for?
1997 Ford Probe Logo

Related Topics:

716 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...