Question about 1981 Ford F 100

Open Question

Whats the clutch pressure plate torq spec on a 300 s

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mindreader
  • 578 Answers

SOURCE: i need the torque specs for a ford 300 inline 6

Tighten all bolts to 10 Lbs, then 20 Lbs, then 35 Lbs.
That should be fine for the 6 cylinder flywheel.

Posted on Oct 10, 2009

kyleyeo23
  • 31 Answers

SOURCE: looking for the torque specs for the pressure

15-25lbs there should be 6 bolts apply lock tite to bolts and then tighten them all down till they are seated. Pick a bolt(call that bolt #1) and torque it then in clockwise motion skip over the next bolt(bolt #2) to the third bolt(bolt #3). Torque bolt #3 and skip over bolt #4 to bolt #5. Torque bolt #5 and then go to bolt #2 torque it and move to bolt #4 and torque it the last bolt to be torqued is # 6. then go around and do it again to make sure they are all the same. This is how the manufacture says how to do it you can do it anyway that works for you as long as they are all torqued the same and they are between 15-25lbs. If bolts are new I would take them to 25lbs if they are the lod bolts I would stay closer to 15lbs that way you dont snap them off.

Posted on Feb 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

? looking the bolt tension specs for flywheel and clutch pressure plate for 4hf1 thank you


Torque Specification - National Truck Spares ' Parts

www.nationaltruckspares.com.au/Parts.aspx?ProductTypeID=8...
1073, 4BC2 tq, Isuzu, Torque Specification, KT26 TLD57 NKR57 NPR57 ... 1075, 4HF1Tq, Isuzu, Torque Specification, NKR66 NPR66, 92 - 03, 4HF1, 4334

Small Block Chevrolet V8 Engine Specs ' Torque Specs ...

boxwrench.net/specs/chevy_sb.htm
Flywheel (Clutch). Thread Locker, 60 ft-lbs. Clutch Pressure Plate, Thread Locker, 35 ft-lbs. Centerbolt. (Harmonic Damper). Engine Oil, 60 ft-lbs. Bellhousin

Nov 07, 2015 | Cars & Trucks

1 Answer

Flywheel, clutch plate, pressure plate tightening torques of all high tensile bolts used to retain these clutch parts


If you are replaceing clutch, there may be instructions. If you purchaced new clutch from autoparts store, they should be able to give you specs.

Mar 04, 2015 | Cars & Trucks

1 Answer

What are the torqe specs for 2006 H3 fan/clutch and water pump


special tools you need EN 48543 FAN CLUTCH HOLDING TOOL. J41240 FAN CLUTCH REMOVER AND INSTALLER. TORQUE FOR FAN CLUTCH NUT 41 LB FT. FOUR BOLTS TO FAN BLADE TORQUE 20 LB FT.WATER PUMP BOLTS TORQUE TO 11 LB FT. DONT NEED SPECIAL TOOLS REMOVE WATER PUMP.

Nov 29, 2012 | 2006 Hummer H3

1 Answer

Clutch changing


please spend $25 and get a mechanics manual for your vehicle there are far too many things to explain.. the $5 answer would be:
1. remove trans from engine
2. unbolt pressure plate incrermentally and evenly as not to distort pressure plate
3. check flywheel for run-out, end-play, scoring and burnishing on flywheel/pressure plate, turn,re-surface/replace if req'd
4. install new pilot bearing clutch disc using special alignment tool and torque all bolts to factory spec and procedure , some recomend new bolts
5.reassemble in reverse order

Oct 04, 2010 | 1997 Mitsubishi Eclipse

1 Answer

I need the torque specs for a ford 300 inline 6


Tighten all bolts to 10 Lbs, then 20 Lbs, then 35 Lbs.
That should be fine for the 6 cylinder flywheel.

Oct 08, 2009 | 1997 Ford F150 Regular Cab

1 Answer

91 legend clutch specs


I am assuming you have never installed a clutch before. What you are asking about is a clutch alignment tool. It is a tool made from plastic that is identical to the output shaft of the transmission.

As you put the clutch disc, pressure plate up against the flywheel, just start the 6 or 8 bolts, but before tightening them down, push the clutch alignment tool all the way into the flywheel pilot bearing. The trick of this tool is to get a close approximation of alignment between the pressure plate, clutch disc and flywheel before tightening down the pressure plate bolts.

Depending on how good your eye is, will determine how easily your transmission will line up and slide in place.

As for any specs, there are none. It all in the eye.

Bill

Sep 21, 2008 | 1991 Acura Legend

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...