Question about 2003 Mercury Mountaineer

1 Answer

Rear Signal Malfunction

I have a 2003 Mercury Mountaineed which has both rear signal malfunctioning. I check the fuses and cannot find a blown one, besides the fuse area in the engine compartment and under the driver side, is there another fuse box to locate which might control the rear signal lights?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 193 Answers

Just take out the globe and replacing them or spray some wd40 inside the connections and see if they work.

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What causes blinker to blink real fast


Could be a bad bulb ,plug, wire, or flasher; Check the side marker lights also, some are connected to the turn signal.

Nov 27, 2016 | Cars & Trucks

2 Answers

Brake light on driver side isn't working tried changing fuse and bulb and still no luck ?


Sometimes the housing the bulb is in has gone bad try cleaning out the prongs where the bulb goes in it that does not work replace the fixture the bulb goes in had the some thing happen to my trailblazer hope this helps

Jul 31, 2015 | 2006 Chevrolet Chevrolet Cobalt LS

1 Answer

Abs warning lamp circuit malfunction-11 left front wheel speed input signal-21 right front " "-22 left rear " ...


Have you checked the fuse ??? if so i would suspect wiring . Or the abs ecm mogul

Jan 23, 2011 | 1995 Buick Regal

3 Answers

How do i check my codes in a 86 nissan z24 pickup


The self-diagnostic system identifies malfunctions of signal systems such as sensors, actuators and wire harnesses based on the input signals received by the ECCS control unit. Various malfunctions are coded and displayed on the control unit by a series of blinking red and green lights. Results of the self-diagnosis are retained in the control unit's memory and are displayed when the mode selector, located on the rear of the control unit, Fig. 122, is switched to the On position. When displaying malfunction codes, the code number can be determined by counting the number of light pulses. The red light represents the first digit of the code, while the green light represents the second digit of the code. For example, a Code 32, would be displayed as three flashes of the red light, followed by two flashes of the green light. Malfunction codes can be translated as follows:
  1. Code 11 -- Crank angle sensor circuit malfunction.
  2. Code 12 -- Air flow meter malfunction.
  3. Code 13 -- Water temperature sensor circuit malfunction.
  4. Code 21 -- Ignition signal malfunction.
  5. Code 23 -- Idle switch circuit malfunction.
  6. Code 24 -- Transmission switch and clutch switch circuit malfunction.
  7. Code 32 -- Starter signal malfunction.
  8. Code 42 -- Throttle sensor circuit malfunction.
  9. Code 43 -- Injector circuit malfunction.
  10. Code 44 -- All monitored systems satisfactory.

May 10, 2010 | 1986 Nissan Pickup 4WD 1986

1 Answer

The right rear turn signal blinks quickly in a


I believe this car has a rear bulb that has two fillaments, one for side lights the other shared for braking and flash. sounds like a blown bulb or a bad ground connection. Check the bulb and the bulb holder and ground connection.
Turn signal blinking quickly generally indicates a blown bulb front or rear or bad connection.

Dec 20, 2009 | 1993 Mercury Cougar

1 Answer

Trouble code c1223 and c1244 for toyota


C1223 - Left Rear Wheel Speed Sensor Input Signal is 0
C1244 - Powertrain Indicated Engine Drag Control Malfunction

Oct 20, 2009 | 2003 Toyota Sequoia

1 Answer

The turn signals do not work on 2000 nissan exterra.Fuse was blown. Replaced and blew again after a few seconds.


1.Remove front & Rear turn signal Bulbs.
2.Replace Fuse.
3.Signal on.
4.Fix rear Signal Bulb.
5.Fix Front Signal Bulb.
7.If your Fuse blown.
8.Defect is There.

Jun 11, 2009 | 2000 Nissan Xterra

1 Answer

Rear turn signal indicator


There is a fuse under the hood in the fuse/relay box by the driver side fender marked LR TURN that is probably blown,each corner has own fuse.

Sep 11, 2008 | 2003 GMC Sonoma Extended Cab

Not finding what you are looking for?
2003 Mercury Mountaineer Logo

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...