Question about 2001 Daihatsu Move

Open Question

What size is a move l600 clutch

1998 l600 model

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 1998 Dodge Dakota 3.9 with a 5 speed. I am having difficulties with the clutch and am trying to figure out if it is the clutch needing replaced or if it is the hydraulics.

Bad hydraulics (leaking/spongy) and worn out clutch have opposite symptoms. If the clutch does NOT ENGAGE - get the vehicle moving - you probably need to replace the clutch and/or pressure plate.
If the clutch does NOT DISENGAGE - you can't get the transmission into gear, or there is difficulty or grinding when trying to shift between gears - your hydraulic system is not moving the clutch release arm far enough to disengage the clutch.

Jun 09, 2017 | 1998 Dodge Dakota

1 Answer

Clutch pedal moves sideways

Go under the dash and look at the clutch pedal pivot bolt, is it loose or is the brace it is bolted into breaking away>

Aug 08, 2012 | 1998 Chevrolet S-10 Pickup

1 Answer

My 1998 Honda civic ex won't move but the motor

Have you just replaced the clutch? Taken out the transaxle, and put it back in? Are you sure transmission was in good condition before this? If so, review your procedure carefully to be sure you got it all back right.
Watch the slave cylinder while someone depresses clutch. You should see the little plunger move slightly out and move the clutch lever back. The lever moves the release bearing inside bell housing into contact with the pressure plate. If slave cylinder doesn't move at all, try bleeding again. The plunger has to move when clutch is engaged.
I'm not sure what you mean by "will shift but won't go into gear". You mean it's actually going into a gear position and car won't move? Or it won't go into any gear, period. As if you had no clutch?

Nov 06, 2011 | 1998 Honda Civic

1 Answer

Manual ford f-150 stuck in first and will not shift into any other gear please help !!!!!!!!!!!!!!!!

will try to help. what year of the truck? this matters!! is clutch working? inother words, can you see the clutch on transmission,yolk, or arm, moving in and out? try pumping the clutch several times, depending on what year model, it may only be low on fluid. it matters whether it's a hydraulic clutch or a manual clutch. i suggest you repost your question with as much information about your truck,year, make model,engine size,as possible. this helps us determine where and as most information as possible to relay to you!! as always, thank you,for choosing,

Nov 26, 2010 | Ford F-150 Cars & Trucks

1 Answer

My turbo is stuck and the blade is not moving(not moveable by fingers) is there any chemical that can use to enable it to move the engine wasnt start for quite sometime the turbo is ihi rhf3 from move...

the acid required to remove carbon buildup will also burn into the steel,try wd 40 and tapping it with a small hammer, if it moves,great, if not buy another turbo.but even if you free up the rotor for the turbo,when you fit it it could burn out VERY quickly.

Oct 09, 2010 | Daihatsu Charade Cars & Trucks

1 Answer

The clutch on my 1998 ford escort is not getting power

Hi Friend:

#1) On your Model you have a Clutch Master Cylindr, Check your Resevoir to see it its FULL of Fluid.

#2) If it is Then you need to Check to See if when you Push the Clutch Down its Pushing the Pin or Accuating Arm Under your Vehicle on Right Side of Car. You'll need a Helper to Push the Clutch.

#3) If its Not Moving the Rod to your Throw Out Bearing Accuating Arm Then You'll need to Replace the Master Cylinder and Possibly Your Slave Cylinder Underneath Its what Pushes the Pin To Disengage your Clutch.

#4 If its Moving and Pushing the Pin.Then Your Throw Out Bearing is Bad or Your Clutch and Pressure Plate.

#5) Which to Replace These you'll have to Pull the Transmission to Remove and Replace them with New Ones.

I hope this has helped you Please let me Know by Voting for the Solution I have Given You. Thanks For Using FIXYA From: d_hubbs

Jul 30, 2010 | 1998 Ford Escort

1 Answer

1998 Saturn SC1 manuel stick is hard to shift into 1st & 2nd gear

Try to double clutch the clutch pedal. How to double clutch; push the clutch in moving the stick to neutral, then release the clutch and then push it back in and shift into first or second gear. If it works then it is not the shift linkage and could be a clutch adjustment. First how far do you have to release the clutch pedal until the clutch plate starts to engage? If only an inch or so the clutch pedal needs to be adjusted, which is an easy fix (this is more common). The other possible problems could be the clutch plate, throwout bearing of syncros could be bad. If it is one of the previous problems double clutching should buy you some time.

Jul 01, 2010 | 1998 Saturn SC

1 Answer


depending on what tranmission you have depends on the size of the clutch but as for you question the s-10 series trucks have a hydraulic clutch

Jan 06, 2010 | 1998 Chevrolet S-10 Pickup

2 Answers

1998 crown victoria compressor doesent work

The clutch itself is the problem (and much cheaper)--replace only the clutch. You might check with a local wrecking yard for such a part. If the compressor was the problem, when the clutch engaged, the drive belt would either break or be thrown off.

Sep 20, 2009 | 1998 Ford Crown Victoria

1 Answer


Do u have play in the pedal? when does the clutch start to engage when u let it out to move? close to the top means the clutch plate is worn out.

Mar 15, 2009 | 1998 Suzuki Sidekick

Not finding what you are looking for?
2001 Daihatsu Move Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

79186 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides