Question about 2005 Chrysler Pacifica

1 Answer

I need to know where the water pump is located?Is it on the side where the pulleys are and above the oil pan?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 2,984 Answers

Removal & Installation

To Remove:

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain cooling system. NOTE: The water pump is driven by the timing belt.
  3. Remove or disconnect the following:
    • Engine timing belt
    • Water pump mounting bolts and note position of longer bolt
    • Water pump body from engine
To Install:
NOTE: It is normal for the water pump to leak a small amount of coolant from the weep hole. Do not replace the water pump if this condition exists.
  1. Clean O-ring surfaces on pump and cover.
  2. Apply Mopar Dielectric Grease or the equivalent silicone grease to the O-ring.
  3. Install or connect the following:
    • New O-ring on water pump
    • Water pump to engine.
    • Mounting bolts
      1. Torque to 105 inch lbs. (12 Nm)
    • Timing belt
  4. Fill cooling system.
I need to know where the water pump is located?Is - 7b1bbf4.gif

Posted on Jun 23, 2009

  • Greg Bernett
    Greg Bernett Jun 23, 2009

    Looking at the engine from the top, the water pump is the letter "E"...so it is towards the top of your motor.



×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace a water pump on a 2005 dodge grand caravan water pump is leaking, added fluid but is still leaking and now more frequently want to replace it as a do it ourselves


this isnt a solution,just a suggestion.my husband,a fairly skilled home mechanic,recently did this.it took 12 hours over a 2 day period.you have to remove everything from the front of the motor,including the motor mounts,to access the pump.make sure you change the timing belt at the same time if it shows ANY signs of wear so you aren't doing the procedure again anytime soon..good luck!!

Mar 02, 2011 | 2005 Dodge Grand Caravan

3 Answers

Where is crank sensor located


Lower front of engine derictly behind hormonic balancer IE the lower pulley on engine but before the oil pan two wires fairly easy to replace

Dec 05, 2010 | 2006 GMC Canyon

1 Answer

I need to know where is the oil presure switch of a 2003 ford windstar 3.8l


On a 1996 3.8 L Should be under the power steering on the block. Looking at the pulleys on the right side just above the oil pan. This would involve removing the pwr steering punp and hoses.

I don't know if a 2003 is different.. You could inspect the area visually to check it.

To get to replace it...
96 - 98 windstar 3.8 oil pressure switch is located under power steering pump. Remove serpentine belt and alternator. Remove PS pump pulley with special puller to get access to PS pump bolts. Drain PS pump and remove PS hoses. Remove PS pump.

Nov 30, 2010 | 2000 Ford Windstar

1 Answer

Water leak


Check behind the pulley of the water pump,it is most likely leaking and needs replacing,the water pump.

Jun 05, 2010 | 1997 Jeep Grand Cherokee

3 Answers

Locate the oil pump how to change it


The location of the oil pump is located inside the engine oil pan. The oil pan being on the very bottom of the engine. This would be a fairly difficult job for a beginner. Highly suggest obtaining a manual with specific directions. Disconnect battery, Make sure to remove intake plenium for clearance when jacking engine after disconnecting engine mounts, and losen only on the rear transmission mount. It will also be necessary to disconnect radiator connections hoses and transmission lines if automatic, on the safe side many people just remove the radiator all together to avoid damageing it with the engines bottom pulley when lifting/jacking engine. The engine will have to be lifted enough to facilitate the removal of the oil pan. Caution, sometimes the oil pump/ pick up screen tube assy. will have to be disconnected before the pan will clear these can just be dropped into the pan. Also, it is not uncommon to have to rotate the crank by the front pulley in order to get the cranks throws to clear the pan as well. Remember going back together you may have to slide the oil pan in place first then put the new oil pump in. This will be tight work and you may do a lot of swearing! Caution again never work in these close areas without supporting the engine on some wooden blocks! I have used short pieces of 4x4's in the past, make sure the engine is securely supported. Remember when going back together to retighten everything you loosend make a list. Before doing all this work please do an oil pressure check and not just rely on the gauge as an indicator to change the oil pump. Also, if an engine has not been serviced regularly the engine oil pan could have a build up of sluge blocking the oil pump's pickup screen therefore decreasing the oil pressure. God Bless

Sep 21, 2009 | 1993 Ford F150 SuperCab

2 Answers

Dodge 2005 Grand Caravan water Pump replacement


JUST COMPLETED THIS JOB TODAY. MAKE SURE THE ENGINE HAS COOLED DOWN . IT TOOK APPROX 2 1/2 HRS. DISCONNECT THE NEGATIVE POST ON THE BATTERY. JACK UP PASSENGER SIDE FRONT AND SUPPORT ON JACK STANDS. REMOVE PASS. FROUNT TIRE. DRAIN RADIATOR INTO CONTAINER FOR PROPER DISPOSAL OR REUSE. USING FLOOR JACK PROVIDE SLIGHT TENSION ON OIL PAN WITH A SHORT 2 X 4 WOOD PIECE TO PROTECT OIL PAN. LOOSEN 3 ENGINE MOUNT BOLTS ON PASS. SIDE OF ENGINE COMPARTMENT. ALLOW APPROX 1" BETWEEN SHOULDER OF BOLTS AND MOUNT. LOWER ENGINE UNTILL BOLTS ARE SET ONTO MOUNT. REMOVE ENGINE SPLASH SHIELD INSIDE WHEEL WELL OF REMOVED TIRE. LOCATE WATER PUMP AND LOOSEN 3 PULLEY MOUNTING BOLTS (THIS IS WHILE BELT IS ON PULLEY) REMOVE SURPENTINE BELT AND CONTINUE TO FULLY REMOVE THE PUMP PULLEY. IT WONT COME OUT AS THE PUMP & PULLEY HAVE TO COME OUT TOGEATHER. REMOVE 5 WATER PUMP BOLTS AND CAREFULLY WORK WATER PUMP OUT BETWEEN THE ENGINE AND VEHICLE FRAME. CLEAN ALL MATING/GASKET SURFACES AND BOLTS. USING A SMALL AMOUNT OF TACKY SEALENT TO INSURE THE NEW WATER PUMP SEAL STAYS IN PLACE, THE INSTALL IS PRITTY MUCH THE REVERSAL OF REMOVAL.

GOOD LUCK, REMEMBER TO TIGHTEN ALL BOLTS TO MFR SPECS AND BLEED THE AIR OUT OF THE COOLANT AS REQUIRED.

Mar 30, 2009 | 2005 Ford F-150

1 Answer

How to remove the oil pan on a 99 ford contour 2.5


This is quite a chore, you have to lift the engine to do it:

From AutoZone...

Disconnect the negative battery cable.

Remove the water pump pulley shield.

Install engine support device to the engine lifting eyes and support the engine.

Raise and safely support the vehicle.


Remove the exhaust crossover and the exhaust retaining bracket located on the right side of the oil pan.

Remove the exhaust heat shield retaining nuts and the exhaust heat shields from the left side of the oil pan.


Feb 23, 2009 | 1999 Ford Contour

1 Answer

I have no idea how to remove the water pump pulley!


Ok, now I know for sure what the problem is, the water pump pulley is pressed on, u will need to disconnect the top side engine mount and raise the engine up about a foot with a floor jack, make sure u put the jack saddle somewhere where u won't damage the oil pan, if u must lift it by the pan use a flat peice of wood to spread the load, once it is up the pump will slide out, then u must have the old pulley removed and the new one pressed on,I think a power steering pulley remover tool is what u need, Kragen and Autozone will loan these to u free of charge if u want to try and press the pulley off and on yourself.

Jan 05, 2009 | 1991 Oldsmobile Cutlass Ciera

1 Answer

No oil to overhead cam where is the oil pump located


Might have to drop oil pan and check stainer for blockage (clogged), oil pump is located infront of engine front cover case, have to remove crankshaft pulley and other stuff,water punp pulley belts etc.

Nov 22, 2008 | 1992 Nissan Sentra 4 Door

Not finding what you are looking for?
2005 Chrysler Pacifica Logo

2,860 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...