Question about Isuzu Rodeo

1 Answer

What does the A/C pulley and bracket diagram look like?

Need to know exactly how the pulley that adjusts the tension goes on the bracket. Are there any bushings, collars, etc.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Isuzu Master
  • 42,545 Answers

There is a bush that goes on the inside of the pulley bearing and the flange for that bush goes against the bracket. On the other side is a flat washer that retains the pulley on the shaft and either a spring washer and nut or a nyloc nut goes against that flat washer

Posted on May 12, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 186 Answers

SOURCE: can you find an engine diagram for an 02 chevy

That is the water pump bypass/heater hoses you have to get them from the dealer, they know the ones. They are plastic and you should replace both and make sure you get all the pieces out as they will break when removed.

Posted on Aug 02, 2009

  • 484 Answers

SOURCE: 2006 Nissan frontier 4 cylinder belt diagram + tensioner pulley

They are under the hood or on the front crossmember.

Regards,
matt

Posted on Sep 14, 2009

moparownr
  • 667 Answers

SOURCE: 2002 Ford Escort ZX2 serpinten belt routing & tensioner pulley

go to www.gates.com on the lower right hand side under popular topics, click on timing belts, then on the left hand side click Parts Locator and Interchange, enter your cars info and the first page that comes up will show you a camera icon for a pic of how your belt is routed. The tensioner pulley is the one mounted on a silver arm, usually at the top. Hope this helps let me know.

Posted on Sep 22, 2009

greg_margo
  • 1959 Answers

SOURCE: My belt tensioner pulley broke at the bolt that

You should only remove the drive belt shield if you raise the car. Below are step-by-step instructions per the repair manual. Drive Belt Tensioner
Removal & Installation To Remove:

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the drive belt shield at the right wheel well.
  4. Remove the drive belt.
  5. Remove the drive belt tensioner mounting bolt.
  6. Remove the drive belt tensioner.
To Install:
  1. Install the belt tensioner. Torque the mounting bolt to 21 ft. lbs. (28 Nm).
  2. Install the drive belt.
  3. Install the drive belt shield.
  4. Lower the vehicle.
  5. Connect the negative battery cable.



Posted on Oct 30, 2009

  • 334 Answers

SOURCE: 2000 plymouth voyager 3.0 L, I need a diagram of

Hello huckstootief,

I hope this helps.

netvan_103.png


netvan_104.png

Regards,
netvan

Posted on Apr 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace fan belt on a Mitsubishi pajero


Instructions
  1. 1 Open the bonnet of the Pajero, and turn the bolt on the centre of the tension pulley with a socket wrench two full rotations. The tension pulley is the pulley directly behind the fan in the upper portion of the front of the engine.
  2. 2 Loosen the adjuster bolt on the tension pulley bracket. This bolt is on the left-hand side, situated in a long horizontal groove.
  3. 3 Slip the fan belt off of the engine. Draw a diagram of the path of the fan belt if the factory printed sticker diagram is no longer in the front of your engine on your Pajero.
  4. 4 Insert the new fan belt, winding it through the various pulleys according to your diagram. Put it on the tensioner pulley last.
  5. 5 Place the tension belt tool on the tension pulley bolt and pull until the slack in the belt is gone. When there is no slack, keep the pressure on the pulley, and tighten the adjuster bolt with the wrench. Tighten the lock bolt on the pulley.

Jun 17, 2015 | 2006 Mitsubishi Pajero 3.2

1 Answer

I have a dodge dynasty 1990 i replaced my serpentine belt now it wont stay on need to replace my tensioner pully how do i do it?


undo the big nut in front of the pulley. release the tension on the belt by adjusting the small bolt at the rear of the adjuster bracket . Take the nut of the shaft and pull the pulley off. Remember where the spacer goes at the back of the pulley.

Jan 10, 2014 | Hyundai Motor 2005 XG350

1 Answer

How to change altenater belt on 87' cabi



INSPECTION

Inspect the belts for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately. It is always best to replace all drive belts at one time, as a preventive maintenance measure, during this service operation.


CHECKING TENSION AND ADJUSTMENT

See Figure 1
The belt tension on most driven components is adjusted by moving the component (alternator, power steering pump etc.) within the range of a slotted bracket. Some brackets (toothed) use a rack and pinion mechanism which moves the alternator side-to-side to adjust the belt tension. With this configuration, no prying tools are required. On Quantum (except 5 cylinder) and Fox models, the air conditioner compressor drive belts are adjusted by varying the number of discs (shims) between the halves of the crankshaft pulley. Before adjusting the belt tension on any engine, look at the mounting and determine what kind of bracket is used.
To check belt tension, push in on the drive belt about midway between the crankshaft pulley and the driven component. If the belt is less than 39.4 in. (1m) long, it should deflect between 0.80-0.120 in. (2-5mm). For longer belts, it should deflect between 0.40-0.060 in. (10-15mm). Belt size is usually printed on the back side of the belt. If it can't be read, it's probably time to replace it.


0900c1528026638b.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: To check belt tension, push in on the drive belt about midway between the crankshaft pulley and the driven component
Slotted Brackets
See Figures 2, 3 and 4

  1. Loosen the adjustment nut/bolt in the slotted bracket. Slightly loosen the pivot bolt.
  2. Pull (don't pry) the component outward to increase tension. Push inward to reduce tension. Tighten the adjusting nut/bolt and the pivot bolt.



0900c1528026638c.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Alternator mounting with slotted brackets

  1. Components, such as the power steering pump and some air conditioner compressors, may be mounted with a double slotted adjusting bracket using a threaded bolt and locknut to adjust and maintain tension. Loosen the locknut(s) and slightly loosen the bolt(s) in the slotted groove(s). Turn the threaded adjustment bolt(s) in or out to gain correct tension. Tighten locknut(s) and slotted bracket bolt(s).
  2. Recheck the drive belt tension, readjust if necessary.



0900c1528026638d.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Some components use a double slotted adjusting bracket with a threaded bolt and locknut to adjust and maintain tension. Loosen the locknut (shown) before adjusting the tension bolt


0900c1528026638e.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: An extension is helpful when adjusting the tension bolt. Be sure to loosen the nut/bolt on the rear slotted bracket first
Toothed Brackets
See Figures 5 and 6

  1. Loosen the tension bolt and the alternator pivot bolt. These bolts should be loosened until the alternator swings freely under its own weight.



0900c1528026638f.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Loosen the tension bolt (shown) and the alternator pivot bolt until the alternator swings freely under its own weight

  1. Adjust the V-belt by turning the nut on the tension bolt while checking the belt deflection with your thumb.
  2. Once the proper tension is achieved, tighten the tension bolt to 26 ft. lbs. (35 Nm). Tighten the pivot bolt to 15 ft. lbs. (20 Nm).
  3. Recheck the drive belt tension, readjust if necessary.



0900c15280266390.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Adjust the V-belt by turning the nut on the tension bolt
Split Pulley
See Figure 7
On Quantum (except 5 cylinder) and Fox models, the air conditioner compressor drive belts are adjusted by varying the number of discs (shims) between the halves of the crankshaft pulley.

  1. Remove the nuts/bolts securing the tensioner plate and crankshaft pulley halves.
  2. Add or remove the amount of spacer discs between the pulley halves until the belt tension is correct.



0900c15280266391.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Belt adjusting shims on Quantum (except 5 cylinder) and Fox models. Extra shims are stored behind the tensioner plate on Fox and turbo diesel Quantums (shown)
If there are any shims left over, do not throw them away. On Fox and turbo diesel Quantum models, store the extra shims in front of the split pulley (behind the tensioner plate). On Quantums with 4 cylinder gas engines, store the extra shims behind the split pulley (in front of the crankshaft hub).

  1. Secure the pulley halves. Torque the pulley nuts or bolts to 15 ft. lbs. (20 Nm).


REMOVAL & INSTALLATION

If a belt must be replaced, the driven unit must be loosened and moved to its extreme loosest position (usually by moving it toward the center of the motor). After removing the old belt, check the pulleys for dirt or built-up material which could affect belt contact. Carefully install the new belt, it may appear to be just a little too small to fit over the pulley flanges. Fit the belt over the largest pulley (usually the crankshaft pulley at the bottom center of the motor) first, then work on the smaller one(s). Gentle pressure in the direction of rotation is helpful. Some belts run around a third or idler pulley, which acts as an additional pivot in the belt's path. It may be possible to loosen the idler pulley as well as the main component, making your job much easier. Depending on which belt(s) you are changing, it may be necessary to loosen or remove other interfering belts to get at the one(s) you want. Some models have a front engine mount installed through the air conditioner compressor belt circle. Support the engine and remove the mount prior to belt removal and installation.
When buying replacement belts, remember that the fit is critical according to the length of the belt, the width of the belt, the depth of the belt and the angle or profile of the V shape (always match up old belt with new belt if possible). The belt shape should exactly match the shape of the pulley; belts that are not an exact match can cause noise, slippage and premature failure.
After the new belt is installed, adjust it for proper tension. This is sometimes a three or four-handed job; you may find an assistant helpful. Make sure that all the bolts you loosened are retightened and that any other loosened belts also have the correct tension. A new belt can be expected to stretch a bit after installation so be prepared to re-adjust your new belt.
After installing a new belt, run the engine for about 5 minutes and then recheck the belt tension.

May 19, 2012 | 1987 Volkswagen Cabriolet

2 Answers

I followed the serpinetine belt routing diagram for 1994 lincon mark VIII that was on the hood and double checked to make sure it was the right belt and the belt is coming forward off the pulleys.


Then it is too loose. Double check but I'm pretty sure your adjustment is on the Alternator bracket. You loosen the bottom bolt which allows it to picot on the bracket, then loosen the upper bracket bolt and pull it outward to tighten it, lock the bolts back down and it should resolve your problem. If you have a spring loaded assembly that applies tension and you have to release to get the belt on and off then you may need to replace that or your not getting the belt all the way on. If even one of those channels on that belt don't line up properly the belt will work itself off. If you have a frozen or damaged pulley it will do this as well.

Jun 02, 2011 | Lincoln Mark VIII Cars & Trucks

1 Answer

I need a diagram to see were my tension-er is


I don't have the figure for your car, but the below figure shows how to remove the A/C belt.
the other belts should have a simple slot in the bracket for adjusting. If you have more questions, let us know.

6f92dc6.jpg
3.0L SOHC Diamante
  1. Disconnect the negative battery cable.
  2. Loosen the lockbolt on the face of the A/C tensioner pulley.
  3. Turn the adjusting bolt of the A/C tensioner pulley to loosen the tension of the A/C belt.
  4. Remove the A/C compressor belt.
  5. Loosen the locknut on the face of the power steering/alternator tensioner pulley.
  6. Turn the adjusting bolt of the tensioner pulley to loosen the tension of the belt.
  7. Remove the power steering/alternator belt.
To install:
  1. Install the power steering/alternator belt first and then the A/C compressor drive belt.
  2. Adjust the belts to the proper tension by turning the adjusting bolts and tighten pulley fixing nut/bolt.
  3. Tighten the mounting nut of the power steering/alternator tensioner pulley to 36 ft. lbs. (50 Nm).

NOTE The manufacturer does not provide a torque specification for the bolt that secures A/C tensioner pulley.
  1. Connect the negative battery cable.

Oct 06, 2010 | 1994 Mitsubishi Diamante

2 Answers

1998 Buick Park Avenue, replaced serp belt, but now no tension.


Hello. The tension can be adjusted. Just loosen the tensioning pulley, use a crow bar to put tension on the serpentine belt and tighten that tensioning pulley back down. Joe

Apr 15, 2010 | 1998 Buick Park Avenue

1 Answer

Serpentine belt diagram for 2003 chevy cavalier 2.2l ohc


That pulley is the tensioner pulley. It is either manual or automatic. If it is a manual tensioner, the bracket that it is attached to it should have a square hole located on it bracket somewhere. This whole will look inoculous, but will be offset from the pulley. If you have a 3/4" socket wrench, you'll notice it fits nicely into this hole.

You use this hole (and the wrench) to twist the whole bracket and apply tension while you tighten the bracket itself down.

An automatic tensioner will have a spring inside and would pretty much work by itself when a belt of the proper length is installed. Your Hanynes manual would have already alerted you to how to adjust an automatic tensioner.

I hope that helps.

BTW, the tensioner pully usually rests on the back (flat) side of the belt and has no device attached to it.

Aug 15, 2009 | 2003 Chevrolet Cavalier

1 Answer

I broke timing belt when replacing hormonic balancer


Here are some. Hope it helps =D

Timing Marks

Diagram


TORQUE SPECIFICATIONS
Application Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt 37 (50)
Alternator Bracket Adjuster Bolt 16 (22)
Alternator Bracket Bolt 33 (45)
Balance Shaft Pulley Bolt 22 (30)
Camshaft Pulley Bolt
2.2L DOHC 37 (51)
2.2L SOHC & 2.3L 27 (37)
Crankshaft Pulley Bolt 184 (250)
Power Steering Belt Adjuster Nut 11 (15)
Power Steering Pump Bracket Bolt 33 (45)
Power Steering Pump Mounting Bolt 16 (22)
Shift Cable Bracket Bolt 16 (22)
Timing Belt Tension Adjuster 33 (45)
INCH Lbs. (N.m)
Timing Belt Cover Bolt 108 (12)
Valve Cover Nut 90 (10)
Water Pump Bolt 108 (12)

Jun 28, 2009 | 1992 Honda Accord

1 Answer

Adjust tension on fan belt


Your '90 Benz has a belt tensioner that is automatic. You just insert the correct tool to ease the tensioner pulley, (The tool is inserted into the bracket for the tensioner pulley), to the left as you're facing the car. Then slip your serpentine belt off. Reinstallation is a reversal of this process. (I believe it's to the left, don't quote me on that)

The radiator support in front, should have a diagram of how the serpentine belt goes on the pulleys.

If your serpentine belt slips, then the belt tensioner pulley assembly is bad, needs to be replaced, or the serpentine belt itself is worn out.

Apr 19, 2009 | 1990 Mercedes-Benz 300 Diesel

1 Answer

Drive belt is loose on 6 cylinder 96 jeep. How do I adjust it?


You will Probably need a New Belt Tensioner. Draw a Diagram of the Belt Routing Before Removal of the Belt.You will need to Locate the Belt Tensioner. It has a Large Pulley on a Bracket that Has a Bolt in the Middle and a Smaller Pulley that Goes Under the Belt and Holds Tension on it. You will need to get a Wratchet, Socket, and Cheater Bar. Turn the Bolt On the Top Large Pulley with the Wratchet and Cheater Bar. This will Lower the Smaller Pulley So that you will be Able to Remove the Belt. Please Rate My Response! Thanks!

Feb 02, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...