Question about 1994 Toyota Land Cruiser

1 Answer

How to tighten the air conditioner crank pulley

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 40,710 Answers

As the nut is attached to the ac shaft and not the pulley I would activate the ac clutch so that the pulley will not free wheel and I would use a 1/2 impact gun to do it up or undo it. Use an old belt in the pulley and clamp it at the pulley with vice grips as a means of holding the pulley steady.. If you have the compressor off the vehicle clamp the belt in a vice next to the pulley instead of the vice grips

Posted on May 12, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ac, altenator & crank pully alignment


The crank pulley is a 2 piece part, the outer pulley "ring" is insulated from the inner pulley by a special sandwiched rubber ring. The outer pulley on may "walk" off the inner pulley due to engine vibration, this is most common on 4 cylinder engines. The crank pulley is the only pulley that can do this.

Jul 17, 2016 | 2000 Toyota Camry

2 Answers

My crank pulley is loose on 2009 jeep Cherokee how do I tighten


There is one bolt in center of pulley/harmonic balancer. Sounds like the harmonic balancer has started going bad..if bolt in center of pulley is loose...which is fairly uncommon tighten which you just tighten Iike any other bolt. If it is tight then you will need the replacement. Replacement is a good bit more involved. Radiator has to be removed, special tool, harmonic balancer pulley remover is required..it will remove pulley. Then you line up pulley with keyway..tap on with rubber hammer until pulley is on far enough for bolt to be started..tighten the bolt and it pulls the pulley all the way into place.

Sep 22, 2015 | Jeep Cars & Trucks

1 Answer

Crank shaft Pulley Coming out of 2001 Chevy Malibu, how do I tighten it back up?


with a socket on air impact wrench or with socket on breakabar. put in a first gear.if auto put in park.tighten with hand power should be enough.

Feb 05, 2014 | 2001 Chevrolet Malibu

1 Answer

I have 1996 Kia Sephia. When the air conditioner is on, the power steering doesn't work about half of the time and the car makes a squealing noise when turning, starting, and sometimes when idling....


Loose belt-tighten or worn idler pulley bearings.Tighten belts first and if the squeel is still there remove belt and check all pulley bearings.Grab the pulley by hand and give it a wriggle-there shouldn't be any play axially

Aug 10, 2011 | 1996 Kia Sephia

1 Answer

How do you get the air conditioner belt on all 3 pulleys on a 2003 nissan xterra


one of the pulleys should be a tensioner. meaning you put a wrench or a socket on the bolt head in the center of the pulley and crank on it. slip the belt on all pulleys and then release the pressure on the wrench.

Jul 29, 2010 | 2003 Nissan Xterra

1 Answer

How do i take off the old water pump on 1996 geo metro 4 cyl?


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the air cleaner.
  4. Remove the suction pipe bracket for the A/C compressor, if equipped.
  5. Loosen but do not remove the 4 water pump pulley bolts.
  6. Raise and safely support the vehicle.
  7. Remove the lower splash shield.
  8. Remove the A/C compressor drive belt, if equipped.
  9. Remove the alternator drive belt.
  10. Remove the crankshaft and water pump pulleys.
  11. Remove the timing belt.
  12. Remove the oil level dipstick and tube.
  13. Remove the alternator adjusting bracket from the water pump.
  14. Remove the water pump rubber seals.
  15. Remove the water pump mounting bolts and nuts and remove the water pump from the engine.


ae1b66e.gif
Water pump mounting location

  1. Clean the gasket mating surfaces thoroughly.
  2. Check the water pump by hand for smooth operation. If the pump does not operate smoothly or is noisy, replace it.
  3. Install the pump using a new gasket. Tighten the bolts to 115 inch lbs. (13 Nm).
  4. Install new rubber seals.
  5. Install the upper alternator adjusting bracket and tighten the bolt to 17 ft. lbs. (23 Nm).
  6. Install the oil level dipstick and tube.
  7. Install the timing belt.
  8. Install the water pump and crankshaft pulleys. Leave the water pump pulley bolts hand-tight.
  9. Install the alternator drive belt.
  10. Install the lower alternator cover plate and tighten the bolts to 89 inch lbs. (10 Nm).
  11. Install the A/C compressor drive belt, if equipped.
  12. Install the lower splash shield and lower the vehicle.
  13. Tighten the water pump pulley mounting bolts to 18 ft. lbs. (24 Nm).
  14. Adjust the water pump drive belt tension and tighten the alternator adjustment bolt to 17 ft. lbs. (23 Nm).
  15. Install the suction pipe bracket for the A/C compressor, if equipped.
  16. Install the air cleaner.
  17. Refill the cooling system.
  18. Connect the negative battery cable.
  19. Start the engine and check for leaks.


83667f6.gif Water pump assembly showing rubber seal location


  1. Disconnect the negative battery cable.
  2. Drain the cooling system.

    CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

  3. Remove the air cleaner assembly.
  4. Loosen but do not remove the four coolant pump pulley bolts.
  5. Raise and support the vehicle safely.
  6. Remove the lower splash shield.
  7. Remove the air conditioner compressor drive belt.
  8. Remove the lower alternator cover plate bolts, loosen the alternator adjusting bolt, and remove the drive belt.
  9. Remove the crankshaft pulley.
  10. Remove the coolant pump pulley.
  11. Remove the timing belt.
  12. Remove the oil level dipstick and guide tube.
  13. Remove the alternator adjusting bracket from the water pump.
  14. Remove the water pump rubber seals.
  15. Remove the water pump mounting bolts and nuts. Remove the water pump from the vehicle.
To install:
  1. Clean the gasket mating surfaces thoroughly.
  2. Check the water pump by hand for smooth operation. If the pump does not operate smoothly or is noisy, replace it.
  3. Install the pump using a new gasket. Tighten bolts to 115 inch lbs. (13 Nm).
  4. Install new rubber seals.
  5. Install the upper alternator adjusting bracket and tighten bolt to 17 ft. lbs. (23 Nm).
  6. Install the oil level dipstick and guide tube.
  7. Install the timing belt.
  8. Install the water pump pulley and leave the bolts hand tight.
  9. Install the crankshaft pulley.
  10. Install the water pump/alternator drive belt.
  11. Install the lower alternator cover plate and tighten bolts to 89 inch lbs. (10 Nm).
  12. Install the air conditioner compressor drive belt by releasing the tensioner pulley and installing belt.
  13. Install the lower splash shield and lower vehicle.
  14. Tighten water pump pulley mounting bolts to 18 ft. lbs. (24 Nm).
  15. Adjust the water pump drive belt tension and tighten alternator adjustment bolt to 17 ft. lbs. (23 Nm).
  16. Install the air cleaner assembly.
  17. Refill the cooling system.
  18. Connect the negative battery cable.
  19. Start the engine and allow it to reach operating temperature. Check for leaks and refill cooling system as necessary.

Mar 06, 2010 | 1996 Geo Metro

1 Answer

Driving to work this morning, all the sudden my wheel tightened up (barely moves), and right before I got to my destination there was a bad knocking sound under the hood (front right-ish). When I went...


sounds like something lock up take belt off and you should be able to turn all pulleys by hand except bottom crank pulley the one that does not turn is your problem

Feb 18, 2010 | 1997 Ford Explorer AWD

1 Answer

Put new water pump on, cannot get belt back on


Unbolt the pulley from the water pump, slip the belt over everything and refasten the the pulley to the pump while the belt is draped over it. Then tighten up the belt.

Mar 13, 2009 | 1999 Nissan Sentra

2 Answers

I need a diagram for a serpentine belt, for a 2000 ford taurus se


Starting at the crankshaft pulley, and going clockwise, the belt leaves the crank pulley,
Goes around the tensioner,
Goes around the water pump
Goes around the alternator
Goes around the upper idler
Goes around the Power Steering pump
Goes around the air conditioner pulley
then goes back to the Crank pulley


Sep 06, 2008 | 2000 Ford Taurus

Not finding what you are looking for?
1994 Toyota Land Cruiser Logo

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...