Question about 1987 Toyota Pickup

Open Question

What are the 1987 Toyota motorhome front rotor bolt torque specs

Need torque specs for the front rotors

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 701 Answers

SOURCE: torque specs for toyota tercel

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Posted on Apr 15, 2009

Suraido
  • 195 Answers

SOURCE: Replace rotors on 2003 4runner

I have never changed it on a 4runner yet, but it's all pretty much the same. Jack the car/truck up, take off the wheel. Loosen the 2 or more bolts holding the caliper to the wheel spindle (the caliper is the C shaped part holding the pads). Take off the caliper, being careful not to rip or break the brake hoses that are bolted to the caliper. DO NOT TAKE THE HOSES OFF! it seems tempting to save time and be sure not to break them, but if you take them off the calipers you will need to bleed the air out of the system, which usually takes a bit of time. Just rest the caliper on the suspension table or any place where it won't fall too easily and where it wont put the hoses in danger. Now with the caliper off, both the pads and the disc should be free to move and remove. On some models the pads are hooked directly to the caliper, and some others like the ones on my toyota echo are in a holder the bolts back on to the caliper. The disc is usually just resting on the wheel studs and should be able to be removed without doing anything to it. In some rare cases, there will be one bolt holding it back, but its just there for centering purposes and is not necessary. So just put the new disc back on, put the pads back on the caliper or in the holder depending on the model, then bolt the caliper assembly back into place and put the wheel back on. And your done, you just need to put the car down and take the jack out.

Posted on Jul 08, 2009

terseo
  • 92 Answers

SOURCE: torque specs for 1998 tercel 1.5L

Main Bearing Cap Torque-42 Ft. Lbs.
Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 Degrees
Rod Bearing Nuts-29 Ft. Lbs.

Hope this helps

Posted on Sep 20, 2009

  • 1861 Answers

SOURCE: need torque specs for a 2002 toyota camry 2.4 for

The 2002 2.4 engine head bolts are 'torqued to distance'.

First, install all the bolts, and, in a sequential fashion, starting at the innermost, working outward, torque all bolts to 70 N-m/806 kgf-cm/58 foot lbs.

Next, mark the front side of each head bolt with a dot of paint. Retighten te cylinder head bolts 90 degrees, starting at the inner 2, and working outward.

We hope that this helps you out.

Posted on Dec 29, 2009

  • 5 Answers

SOURCE: Head bolt torque specs?

I really really really hope you turned the bolts an additional 90 degrees after torquing to 22 Ft-lbs. Otherwise, you may be taking that head off again.

Best of luck,

David

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I need the Torque specs for a 2006 ford escape breaks front and back please


Pad material will cause these problems.... Buy good Cermic pads and new rotors and you won't have that problem

Jan 22, 2015 | 2006 Ford Escape

1 Answer

Volvo torque specs


Along with many of the others the bolts holding the brake caliper slides in place are stretch bolts. You torque them up as pe the first post and then its a twist of so many degrees. This stretches the bolt past its elastic limit. Once used just like an engine head bolt the bolt is scrap. I'm told its to keep the wieght down on the front. My personal feel is that its a dangeous practice because you know loads of Volvos will have had the bolts used for a second and third time.

Jul 19, 2014 | 2005 Volvo S80 2.5

1 Answer

How to replace front brake pads on a How to replace front brake pads on a 2000 Chevy S10 4WD pickup?


First you want to remove brake fluid from brake resovoir, raise front wheels off ground and set park brake or block rear wheels. Remove front wheels, keep steering wheel unlocked so you can turn rotors side to side. Loosen bolts that hold caliper end gently pry caliper free from rotor, remove caliper and remove pads, use bungy cord to hang caliper away from rotor, have rotors measured to see if they are thick enough to have machined, replace if out of specs. Match up pads with old ones, use anti- squeak red liquid and put layer on back of pads, let dry. Use tool to put pistons back into calipers, slowly put pistons back into bore while opening up bleeder screw so ABS won't be damaged. After rotors resurfaced, wash with rubbing alchohal to remove any oils from hands, install rotors and reverse putting pads back onto caliper and reinstall, torque caliper bolts to factory specs and tighten bleeder screws. Install wheels, torque lug nuts to factory specs and replace brake fluid in resovoir. Lower car carefully to ground and press brake peddle without pumping it. Any air in system should bleed out, if not get someone to help with bleeding system. Road test to ensure no squeaks or pulling, burn brakes in slowly.

May 10, 2014 | 2007 Saturn Aura XR Sedan

1 Answer

How to assemble a front wheel bearing on a 2003 GMC Sierra 1500 4x4


The front wheel bearing is a hub and bearing assembly. To remove you will.... 1. Remove the tire 2. Remove the axle nut. You can put a punch in the fins of the rotor to keep the assembly from turning while you rmove the nut. You can can do the same thing when you torque the axle nut. 3. Remove the caliper and rotor. 4. Unplug the abs sensor if equipped. 5. Remove the three bolts that hold the hub to the knuckle. 6. Rmove the hub. If you need torque specs let me know and i'll get them for you. It is absolutely critical that you torque the axle nut to the proper spec!

Oct 08, 2011 | Cars & Trucks

1 Answer

General directions on how to change the front brakes on a Toyota Supra, 1987.


Buy brake pads.
loosen lugs
Jack car, place on jack stand
turn wheel so front of tire is pointing out.
remove tire
remove caliper (two bolts on back side of caliper
slide caliper off rotor.
(if rotor is damaged, see about having it turned or replaced)
take pads off caliper
open hood and remove cap to mater cylinder reservoir
using special tool (or C-clamp and something to protect piston) push the piston back into the caliper fully.
place new brake pads on caliper.
fit caliper on the rotor
Secure caliper to wheel with bolts
replace wheel
remove jack stand
remove jack
tighten lugs on wheel
replace hubcap
start engine (do not drive yet!!!!!)
pump brake pedal until it tightens up
observe reservoir on master cylinder (fill if needed)
replace cap
pump brakes again
take out for a test drive.

good luck and don't forget to vote!!!

Oct 11, 2010 | 1987 Toyota Supra

2 Answers

Replacing the hubs and rotor on my 02 ford excursion i need torque specs


just pull them up tight and dont forget to oil the bolts first so they dont corrode ,the smaller the shank of the bolt the less torque it needs so a bolt with 17mm head would be about 55 or so 19mm head 70 or so it is not rocket science tightening a bolt

Aug 12, 2010 | Ford Excursion Cars & Trucks

1 Answer

What are the torque specs for the bolts on the brake rotors/calipers?


FRONT CALIPAR TO CARRIER 34NM
FRONT CARRIER TO HUB 107NM
FRONT HUB NUT 294NM
REAR CARIER TO HUB 62NM
REAR CALIPAR TO CARRIER UPPER BOLT 39NM
LOWER BOLT 34NM

Apr 25, 2010 | 2003 Toyota Camry

2 Answers

2005 rotor removal toyota


Yes.

And make sure you pay special attention to the proper torque when you put it back on as well as take care when you remove this since the bearing are apt to fall out.

Nov 28, 2009 | 2005 Toyota Corolla

1 Answer

How do I get rotors off front of 87 4Runner?


From memory, to remove the front disc rotors, the hub has to be disassembled completely from the vehicle. The rotors bolt to the hub from behind. Start by removing the calipers, then start disassembling the free wheel hubs, bearings etc.

Jul 19, 2009 | 1987 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...