Question about 2005 Suzuki Vitara

1 Answer

How to set timing belt

How do you set the timing marks and top dead centre

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 20,706 Answers

Which engine.

1.6L 1.8L 2.0L, 2.5L and is it a v6?
if 2.5L
see page.

http://www.fixkick.com/look/odds-ends/suzuki/v6/sv625-chain.pdf

Posted on Jun 02, 2014

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: suzuki vitara 1989

In installing the timing belt, remove the distributor cap, then shift your gear highest speed, say 5th gear, remove the parking brake. Push slowly your car until the rotor points to number one high tension wire plug, That is the TDC, you can now install the timing belt.

Posted on Aug 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When timing my Toyota pickup 1992 what is 5 degrees before to dead center


Hi,when you put the timeing belt on the cank pully is at the 0 mark,wich is (T,D,C)top dead centre,now the other timeing you are talking about is called the ignition timeing,wich is when the spark ignites the fuel and air in the cumbustion chamber,this is why the ignition has to be set 5%(B,T,D,C)before top dead centre.
wright first inline the top dead centre 0mark back up on the crankshaft pully,then take off distributer cap and undo securing bolt so that distributor can turn,
the rotor arm should be pointing at the number one (H,T,L)high tention lead,now slowly turn the distributor anti clock wise,then slowly turn the distributor clock wise,now as it comes up to the number one h,t,lead it should spark,when it sparks tighten the disributor bolt back up,right it should start up and run maybe not to good but it should run,
now buy a timeing light where you can put the 5% into the timeing gun itself,so now put the earth and positive on the earth of the battery and the clip onto the H,T,lead start the car again and point the strobe light from the gun onto the 0T,D,Centre markthe mark should freez every time the light flashes on it ,undo bolt on distibutor and ajust verry slowly when you are happy that the mark is lineing up propperly then I think thts job done.
all the best.

Apr 27, 2015 | Toyota Cars & Trucks

1 Answer

How to reroute the drivibg belt or fan belt


Hi,just inline the crankshaft to the top dead centre marks,then check that the camshaft marks line up,if they dont line up then turn the crankshaft pully again untill the camshaft marks line up,slacken the timeing belt pully adjuster take belt off and replace with new one,tighten the pully adjuster back up,now put a spanner on the crakshaft pully and turn clockwise untill the top dead centre marks and the camshaft marks inline if they dont then slacken the ajusting pully inline marks again and try again,if marks do inline ok then you are ready to start the car.
hope this helps good luck.

Feb 25, 2015 | Cars & Trucks

1 Answer

Set camshaft timing


there should be marks on crank pully and cam belt pully. rotate motor until crank pully timing mark is on zero.the cam belt pully should be lined up with its own mark.number one piston should be at the top of its stroke (top dead centre TDC) and number one valves should be shut. if the cam belt mark is not alined with its own mark remove the belt realine the marks and refit the belt

Sep 15, 2013 | 1993 Subaru Legacy

1 Answer

Replacing timing belt; need timing belt markings for 2000 mazda protege


If it has the twin camshafts, then you need to align the bottom crankshaft pulley marking (there's only one marking at top dead centre). Then you'll need to align the two camshaft pulleys. You need to use the first two sets of markings and then double check the markings on the camshafts themselves, within the valve cover area. Always double check the crank shaft sensor is aligned properly on re-assembly as misalignment will result in a non-start and you might doubt your own work. Don't worry about timing belt failure or misalignment on the twin cam engine as this is a "safe-engine" and will not result in any damage.

Oct 30, 2012 | 1998 Mercedes-Benz CLK

1 Answer

Its time to change the timing belt i need to know the right timing mark and what to do please help and how much it will cost to change it thx


Check the timing marks on the camshaft & crankshaft when #1 piston is @ top dead centre which is marked on the crank pulley where the fan belt goes @ the end of the engine

May 17, 2011 | Toyota Sequoia Cars & Trucks

2 Answers

Timing belt replacement. what are the mark settings on the pulleys?


If you dont know the marks on an engine when replacing the timing belt. There are usually marks on the pulleys and housings to line up. Put the engine on top dead centre TDC from the crankshaft marks before looking for the other marks. If you cant find them Use white out to place your own marks on the pulleys and housings before removing the old belt . To be sure nothing gets out of line mark any pulley that has teeth. It can be useful to take a few digital photos . When fitting the new belt make sure your marks line up again.

Mar 03, 2011 | 1992 Geo Storm

1 Answer

I can find the timing mark I need riset the time on nissan pickup 1986 2wd


Hi,
the timing mark is usually a white painted groove on the main fan belt pulley.
Look for another plate with a a couple of lines or grooves mounted on the engine block right behind the fan belt pulley wheel.
Assuming you have hooked up your timing light per the instructions...When you shine your timing light at this area you are looking to see if the pulley mark lines up with the timing mark on the engine block plate when the engine is at a specific idling speed and the distributor is adjusted to make the timing mark line up when cylinder 1 is firing.
The engine block plate is often marked as 6 deggrees BTDC (before top dead centre). The middle mark is usually top dead centre. (the timing figure could be anything eg 8 deg BTDC..I am just usually an example figure)
See here for more info:
http://www.ehow.com/how_5038331_work-timing-light.html
http://autorepair.about.com/od/tools/a/tools_timinglit.htm
http://everything2.com/title/timing+light

Regrds, Steve
PS Please vote for my answer or add a testimonial if I have helped.

Oct 17, 2010 | 1986 Nissan Pickup 4WD 1986

1 Answer

Set harmonic balancer to top dead centre,set cams to timing marks,engine will not start but turns over. Hyundai Terracan 2002


hi from uk assume you have renewed c/belt and balance shaft timing belt? if so? and sure your timing marks on cams and the c/shaftcog are correct ? the oil pump also correctly aligned with marks? and the balance shaft gear also has time marking ? want to run thro how and which marks you have aligned and at TDC No1 all belt/s have to be aligned ??

Dec 27, 2009 | Hyundai Sonata Cars & Trucks

1 Answer

Timing belt set up


check thr timing gears as they all are marked they line up with arrows on the block make dure the engine is at top dead centre once the belt is on turn over by HAND to make sure you have lined them up ok ore you WILL BEND VALVES and cause big $$$$$$$$ damage if in doubt get back to me Lindz

Mar 14, 2009 | 1998 Subaru Forester

1 Answer

Setting timing marks on a 1998 Ford Escort


think u need a tool it locks the engine at top dead centre then u line cams up

Jul 13, 2008 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...