Question about 1994 Chrysler Concorde

1 Answer

How do I engage my abs brakes in my 94 Chrysler concorde

How do I turn on maybe abs brakes

Posted by Anonymous on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 166 Answers

The ABS function is always on by default. You cannot just turn it off and on.

It only functions during hard or panic stops to prevent the car from skidding out of control. You'll feel a pulsation in the brake pedal under those conditions as it alternately reduces, then re-applys, the brake pressure on any wheel that's beginning to skid.

It does this by monitoring the speed of each wheel, then comparing those speeds to one another. When a wheel is detected to be slower than the others, it indicates a skid is happening, or about to happen, on that wheel. The pressure is then momentarily reduced on that wheel to allow it to regain traction.

Posted on Jan 22, 2015


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1305 Answers

SOURCE: chrysler concord brake lights stay on

Switch is located under the dash and is either on the brake pedal or inline with the brakepedal... either has a clip or is screwed in...
get ready to stand on your head...

Posted on May 28, 2009

  • 97 Answers

SOURCE: 99 Chrysler Concorde electrical problem

probably a relay. relays control switching of power from one compound circuit to another. because you have multiple circuits that are not working, this sounds likely. get a wiring schematic and find out which relay controls that system, then try replacing it.

Posted on Jun 18, 2009

  • 265 Answers

SOURCE: 2001 Chrysler Concorde pressed the brake

That sound you hear is coming from the Vauum Brake Booster...Sooner or later the Brake Pedal will get hard, because the seal inside of the Brake Booster is leaking..And the only way to repair it, is , to replace the Brake Booster...But also check your Vacuum Hose that is instaaled on your Brake Booster..It goes from the Brake Booster, which is behind the Master Cylinder...From there to the Intake Manifold...Just make sure that there are no cracks in that hose, and make sure it is on all the way...because if the hose is bad, then thats all you will have to replace....Goodluck...

Posted on Dec 07, 2009

  • 12 Answers

SOURCE: how to fix the Abs and trac off light on a 2000

take it to a shop that can read abs and I bet it is a wheel speed sensor

Posted on Apr 10, 2010

  • 8743 Answers

SOURCE: location of blend door or

The temperature door actuator is located at the bottom of the heater housing at the center terminal. It looks like this:

To remove the actuator

  1. Remove the left and right underpanel silencer ducts.
  2. Remove the two retaining screws from the actuator which are accessible from the right side of the center stack.
  3. Remove the screw from the actuator on the left side.
  4. Pull the actuator straight down from the shaft and disconnect the electrical wire. Upon removal, matchmark the shaft position of the actuator, because the shaft on this motor is keyed.

Posted on Oct 03, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I put new brake pads on the front and now i dont have a full pedel of brake.The abs light and traction light are both on

how much brake fluid did you remove or put brake shoes on wrong reason abs light on.check brake fluid.when replace front brakes you have make sure mastercylinder reservoir corver on then pump brake pedal seat brake shoes against rotor then check brake fluid level.

Dec 27, 2012 | 2000 Chrysler Concorde

1 Answer

Gauges dont work abs light on and heater wont turn off

abs light means anti lock brake system and the light is telling you that they aren't working properly. you still have brakes it just won't be with the anti lock system your vehicle has. you will need to have your brake system checked out.

Jun 11, 2012 | 1993 Chrysler Concorde

1 Answer

What does a P ! warning light mean on a 94

P sign on your instrument panel means that your parking brake is cocked! release the pedal by kicking it off with your left foot and see if the P sign goes off

Apr 07, 2010 | 1994 Chrysler Concorde

1 Answer

Refrigerant for 94 chrysler concorde????

R143a is what you use, there should be a sticker in the engine compartment for the specs to the amount of R134a used in the A/C system to your car. Good luck and don't over charge the system. Keep me posted be glad to help. 

Jul 03, 2009 | 1994 Chrysler Concorde

1 Answer

Abs light turn off brakes working properly

Do you mean that the light comes on showing a malfunction? It is probably one of the wheel sensors if this is the case.

Jul 03, 2009 | 1999 Chrysler Concorde

1 Answer

I have a 1998 chrysler concorde and my abs light keep popping on and off what may be the problem

first of all i would check the brake fluid cylinder for fluid level you may have a leak there somewhere hope this helps regards Jim

Apr 27, 2009 | Chrysler Concorde Cars & Trucks

Not finding what you are looking for?
1994 Chrysler Concorde Logo

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides