Question about 1999 Kia Sportage

1 Answer

1999 kia sportage oil pan

Trying to take off the oil pan
how many srews are there on the oil pan to take it off

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kia Master
  • 2,984 Answers

There are 19.

Please don't forget to rate! It's what helps us help you!

Thanks!

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace a oil pan on a 02 kia sportage?


Jack up car put on stands remove exhaust if it crosses under sump remove all the screws or nut bang side of sump with a rubber hammer to break seal,clean off old sealer.

Aug 15, 2014 | 2002 Kia Sportage

1 Answer

Do u have to remove transmission to place oil pan


no you dont need to drop the transmission to replace the trans pan or the oil pan its right there on the bottom oil pans usally have 17 or 78 bolts trans pans 20-23 bolts but can differ if this helps please give me a good rating

May 06, 2011 | 1999 Kia Sportage

1 Answer

I cant seperate the oil pan and motor.


If your sure all the bolts are removed, tap the pan sideways with a rubber mallet.

Mar 06, 2011 | 1999 Kia Sportage

1 Answer

Judysmith1405I have a 2001 kia sportage can you tell me where the oil pump is located?


The oil pump is inside the oil pan.The oil pan needs to be removed to get at it.Why do you need to get at the oil pump?They are a component that is usually problem free.If your gauge is showing low oil pressure you likely just need a oil pressure sensor.

Aug 13, 2010 | 2001 Kia Sportage

1 Answer

Does the kia sportage need a cork gasket installed with a new oil pan?


No, the baffle plate is the gasket...if it's not in bad shape put some red Permatex around the block, install the baffle,and oil strainer, then apply the permatex around the oil pan and install.

Jul 12, 2010 | 1999 Kia Sportage

1 Answer

How to remove oil pan on kia sportage 99? thanks,Zak.


Hi Zak:
Kia Sportage 1998-02 Repair Guide
Oil Pan - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable 2 Top intake manifold bracket bolts Front 3 axle housing mounting bolts, 4WD only Left front bushing from the axle housing mount and lower the front axle housing Both gusset plates from the engine Transmission under cover Engine under cover Oil pan mounting bolts and using a scrapper tool separate the oil pan Oil pan Oil strainer assembly Oil baffle 76b1888.jpg


  4. Fig. Exploded view of the oil pan assembly mounting

To install:


f149924.jpg
Fig. Tighten the oil pan bolts in sequence
  1. Clean the engine block, oil pan and baffle pan surfaces of any gasket material.
  2. Apply a continuous bead of Loctite Ultra Blue 587® silicone sealant around the baffle pan.
  3. Install or connect the following:

    Oil baffle. Torque the bolt to 84 inch lbs. (9.5 Nm). Oil strainer. Torque the bolts to 84 inch lbs. (9.5 Nm).
  4. Apply a continuous bead of Loctite Ultra Blue 587® silicone sealant around the oil pan.

    Oil pan. Torque the bolts to 84 inch lbs. (9.5 Nm). Transmission under cover. Torque the bolts to 84 inch lbs. (9.5 Nm). Gusset plates to the engine. Torque the bolts to 33 ft. lbs. (45 Nm). Engine under cover Front axle housing into position. When properly aligned, torque the bolts to 48 ft. lbs. (65 Nm). Intake manifold bracket bolts. Torque the bolts to 34 ft. lbs. (65 Nm). Negative battery cable
  5. Fill the engine with clean oil.
  6. Start the vehicle and check for leaks, repair if necessary.

Hope helps with this (remember rated this) Good luck.

Jan 12, 2010 | 1999 Kia Sportage

1 Answer

Oil pan removal


Follow the steps below.

1. Drain the engine oil.

2. Remove or disconnect the following:

Negative battery cable

2 Top intake manifold bracket bolts

Front 3 axle housing mounting bolts, 4WD only

Left front bushing from the axle housing mount and lower the front axle housing

Both gusset plates from the engine

Transmission under cover

Engine under cover

Oil pan mounting bolts and using a scrapper tool separate the oil pan

Oil pan

Oil strainer assembly

Oil baffle


c94c1d3.jpg

Jul 08, 2009 | 1999 Kia Sportage

1 Answer

How to remove oil pan on kia sprotage 99


jack up motor for clearanc and 12 10m bolts

Jul 08, 2009 | 1999 Kia Sportage

Not finding what you are looking for?
1999 Kia Sportage Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...