Question about 1993 Dodge Dakota

1 Answer

Where is the Sevice Port located?

Was going to have my truck put on a computer to go a diagnostics test but they could not find the service port to connect to.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 194 Answers

I would not go to a place that did not have a service manual or know how to pull one off the internet.
You can find a Dodge Truck forum (just search on it) and gets lots of good information.

Posted on May 11, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: All the wires were taken

Have to get that from a local repair shop
off their data base, such as ALLDATA,Mitchell
etc

Posted on Jun 28, 2011

  • 30 Answers

SOURCE: were is the lower side service port for a/c charge

Both service ports a relatively close to each other. One is next to the Washer fluid reservoir and the other is on top of the Filter/Drier for the A/C system.

Posted on Aug 16, 2008

  • 115 Answers

SOURCE: low side service port

Hi, All air-con systems have stardard size air-con pipe connections.1 small 1large so you can`t connect to the wrong side,the connector usually has a ring you have to pull back to then push onto the pipe connection that when connected keeps the connection tight ,to disconnect it is the reverse of fitting BE carefully and do not connect or disconnect with engine running wear goggles and gloves and do not breath any escaped gas,if your not confident give it to an expert !!.

Posted on Jul 10, 2009

  • 1 Answer

SOURCE: i need to locate the diagnostic port on my 1994

Picture of diagnostic xonnector

Posted on Jul 25, 2011

SOURCE: Where is the diagnostic port located?

under steering wheel

Posted on Nov 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the diagnostic port of my mazda premacy 2000 model located


Typically the OBD2 port is located below the steering wheel, towards the right or left knee. It should have a cover over it saying "diagnostic" or "obd2" another location is under the hood, typically near a fuse panel. This one should definitely have a cover on it saying "diagnostic" or "obd2"

Feb 15, 2016 | Mazda Cars & Trucks

1 Answer

The diagnostic port is not reading


Just fixed mine- Cigarette lighter had a blown fuse , which is also the fuse for the diagnostic port. Check your owners manual to locate diagnostic port fuse,

Nov 30, 2013 | 2004 Lincoln Aviator

1 Answer

Diagnostic Port Location


THE PORT SHOULD BE TO THE RIGHT OF THE STEERING COLUMN. THERE SHOULD BE A RECTANGULAR HOLE IN THE COVER THAT IS UNDER THE DASHBOARD .LOOK HARD WITH A FLASH LIGHT AND YOU WILL FIND IT.GOOD LUCK HUNTING.

Apr 11, 2012 | Cars & Trucks

1 Answer

I have 97 cavalier 2.2. I don't remember were the evaporative emissions systems test port line connects to back side of engine. need a diagram please.


The Evaporative System Service Port is located in the evaporative hose located between the purge solenoid and the canister. The service port is identified by a green colored cap. The port contains a schrader valve and fittings in order to allow the connection of the service tool.


Jul 04, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

Cant find port for diagnostic test


Hi, It is located behind the ashtray, it has to be removed to access the diagnostic port.

Jun 01, 2011 | Acura RL Cars & Trucks

2 Answers

I have a 1994 daihatsu rocky 1.6L efi and want to know where you plug into the computer for a diagnostic test


There is a diagnostic cable which you will require to do the diagnostic test.
There is no need to physically replace chips, connect extra wires, or adjust hardware. Just connect one end of the cable to your computer's RS232 port and the other end to your daihatsu 14-pin Consult port, which is normally located near the fuse box. 




  • Do I need to have my car running while performing diagnostics?
    Most functions require only the ignition to be turned on, not the engine.
  • I'm not a professional mechanic, can I still use this cable and software?
    Yes. This cable and software are designed to be user friendly and easy to understand.
And for getting cable .You can get it from Autozone service centers.


Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Jul 12, 2010 | Daihatsu Rocky Cars & Trucks

1 Answer

Where can I find a connector for the diagnosis an my Honda Accord VI-1996-1998,2.0 TDi,20T2N


Your vehicle should be equipped with OBDII diagnostic computer. If you check in teh area of the passenger side fender or under the dashboard on the drivers side you should find the diagnostic port. If this fail then you can refer to your owners manual for the location of the port.

Apr 07, 2010 | 1992 Honda Accord

1 Answer

How do you pull codes from a 98 bonneville


k, the diagnostic port is located under the dash on the driver's side. Bring the Pontiac to a parts store. They will plug a hand held scan tool into the port and 'read' any codes stored on the car's computer. This is a FREE service. Good luck.

Oct 23, 2009 | 1998 Pontiac Bonneville

1 Answer

Where is the low side service port on a 2003 grand am (6cyl)


If your talking about the low side sevice port to charge your ac, its easy to find. With your recharge kit, it comes with a nozzle to attach to this lowside port. Each port, (lowside and highside), are different diameters. The charging nozzle will ONLY fit onto the lowside port. Just run the length of your ac lines from the compressor and trace them back to the firewall. You should find both ports before you hit the firewall.

Jul 10, 2009 | 2003 Pontiac Grand Am

Not finding what you are looking for?

Open Questions:

See all 1993 Dodge Dakota Questions

1993 Dodge Dakota Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...