Question about 1998 Mercury Mountaineer

1 Answer

Trying to figure out which fuse slot is for brake lights

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 124 Answers

Written on the inner side og fuse box

Posted on May 11, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Installed a brake controller and the green light won't go on. I am told I need to add a fuse where is the fuse box to add the fuse so that the system recognizes the brake controller in a 2002 Eddie...


Hi, this may true if you connected the trailer brake to the connector on the factory wiring harness. There are several fuses that are needed for trailer towing. In the box by the battery, fuses 13, 25, 27, 53, and 54 are needed. You will need a relay in relay slot 19 for the trailer running lights, a relay in relay slot 20 to charge the trailer emergency battery; and, if your trailer has backup lights (6 or 7 wire connector), you will also need a relay in the relay slot 15. If you did not use the factory connector for your trailer brake controller, check to make sure you have connected the controller to an appropriate power source in the truck. Please let me know if you have questions, and thanks for using FixYa.

Jun 22, 2011 | Ford Explorer Cars & Trucks

1 Answer

My brake lights (and dash), went out on my 1992 Celica, I've ruled out the fuses,bulbs and fusable links. Im not getting power to the slot in the fuse box that is allocated for them, but if I run a jump...


You have multiple probs. Dash lights are powered off Headlamp switch, which sounds bad. Brake lights are operated off brake light switch which is just above your brake pedal under dash. Sounds like brake light and head light switch both need to be replaced.

Mar 01, 2011 | 1992 Toyota Celica

1 Answer

Brake light dont work. 2006 chevy truck, 4.8L 2wd


Some of these had two fuses for brake lights. One for the top/center stop lamp and another for the rear left and right brake lights. Usually one said "stop" and the other said "brake" and one was in the underhood panel while the other was in the dash fuse panel. It's not uncommon to blow a brake light fuse [LR and RR] if you tow a trailer but some of these had seperate fuses for the trailer lights also. If you have a test light check both sides of the two fuses for power [ignition key on] while stepping on the brakes. It should at lest narrow your search a bit.

Jun 08, 2010 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

How do I change the brake bulbs on 99 Nissan Quest


The whole assembly will pop out with a screwdriver (carefully). Then the bulbs can be reached. Just push the whole thing back into the slots when you are done.

Feb 17, 2010 | 1999 Nissan Quest

1 Answer

LOCATE SLOT FOR REPLACEING BRAKE LIGHT FUSE BULBS


Over time, some slots that the fuses slide in to can become loose, which causes a bad connection to the fuse. To fix this, you can find which fuse is the problem and then slightly bend one of the male ends of that fuse and the connection should be restored. The particular fuse it sounds like you're talking about is in the engine compartment in the black fuse box closest to the front of the car. There are three (3) 10 amp fuses grouped together, and you could try looking for a loose connection at one of these.

Feb 13, 2010 | Jeep Grand Cherokee Cars & Trucks

2 Answers

Shift lock parking break


ck if your brake lights are working, if not, ck the fuse. if fuse is good and brake lights work, could be problem with solenoid not unlocking the lever, there should be a bypass so you can get it into gear (small slot near shifer, put your key in there to release shifter)

Sep 25, 2009 | 1991 Honda Accord

2 Answers

My brake lights do not work for 1998 ford explorer


Check and make sure you have the right bulbs and fuses installed. However, it sounds like a wiring problem. Probably at the rear of the vehicle. If you are in a "snow" area state, the ice and snow formation can break or pull wires apart. Also, check your ground wires.

Feb 10, 2009 | 1998 Ford Explorer

1 Answer

Brake Lights wont work.


have you tried the brake light switch its located on the brake pedal bracket.

Jan 12, 2009 | 1997 Chrysler Town & Country

Not finding what you are looking for?
1998 Mercury Mountaineer Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...