Question about 2003 Nissan Maxima
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: piston rod bearings
Hello capybluebloo: The torque specs are as follows. Step one tighten to 10-12 ft.lbs. Step two is to tighten an additional 60-65 degrease. I checked two different shop programs and they both say the same. I hope you have access to a degree meter as the degree is very important. Please leave a rating as to quality of your reply as it does help. Should you need more help just ask. Thank You for using FixYa. Roger
Posted on Apr 16, 2009
SOURCE: What are the torque specs
the torque are not mention out side any authorised workshop for that you need to visit the nearest authorised dealer or service centre & leave the rest of work to them without any hazard or trouble or either can start from a torque of 25 to 45 lbs. do not exeed the limit or other wise the nut or even the Axel can get broken in the prossess of facinating it so till then my friend have happy motoring & see you soon.!
Posted on May 08, 2009
1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.
Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.
Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!
Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)
If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.
Posted on Jul 07, 2009
1997 Nissan/Datsun Truck
Pickup 2.4L SFI 4cyl
The Main Bearing Cap Torque:
38 Foot pounds (Final torque)
The Rod Bearing Cap Torque:
Step 1: Torque to 10-12 Ft/Lbs
Step 2: Torque to 28-33 Ft/Lbs
Hope help with this (remember rated this post). TY for using Fixya.
Posted on May 19, 2010
SOURCE: what are the torque specs
Rod cap nut's
Step 1 -10-12 Ft.LBS
Step 2 - 60-65 Additional Degrees
Step 1 - 22 Ft.LBS
Step 2 - 59 Ft.LBS
Step 3 - Loosen all bolt's
Step 4 - 22 Ft.LBS
Step 5 - 86-91 Additional Degrees
Posted on Dec 11, 2010
Tips for a great answer:
Jan 20, 2017 | 2003 Nissan Pathfinder
Sep 24, 2015 | 2000 Nissan Xterra
Mar 25, 2015 | 2002 Chevrolet S-10
Jun 19, 2014 | 2003 Nissan Maxima
Dec 15, 2013 | 2003 Nissan Maxima
Sep 10, 2011 | Nissan Altima Cars & Trucks
May 19, 2010 | 1997 Nissan Pickup
Sep 17, 2009 | 2003 Nissan Maxima
562 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: