Question about Toyota 4Runner

Open Question

What is 2000 toyota 4-runner spark plug wire placement firing order

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: changing spark plugs in a 2004 toyota 4runner

check www.4x4wire.com i was just there looking for the same thing and found step by step directions on how to do it

Posted on Apr 19, 2009

  • 3 Answers

SOURCE: Toyota 4 runner spark plugs

Not a big deal. Realize that the plugs from the factory are Iridium and are good for 100K miles. Assemble the following:

6 Denso IKH20 Iridium Plugs pre-set to .044 gap ($10 each) High Temperature anti-seize (crayon type is $3 at NAPA)
3/8 inch drive ratchet
5/8 inch spark plug socket
4-inch extension
10-inch extension
10 mm socket
12 mm socket
torque wrench (or make real sure you don't over tighten the plugs) new air filter (optional)

Start on the passenger side. Disconnect the air induction/filter assembly by un-snapping the two spring latches on the black air intake box closest to the front of the car. Once these are un-latched, fold the air intake assembly out of the way. Now would also be a good time to replace the air filter if you have not done so lately. With the air intake assembly out of the way, you now have clear access to the top of the valve cover. Along either side on top of the valve cover you will notice three black modules each held in place with one 10mm bolt with a small wiring harness connector attached. These are the coils (one per plug), and the spark plugs are located underneath. Disconnect the wiring harness connector and remove the 10mm bolt. Pull straight up on the coil and it should disconnect from the spark plug. Look down the hole and you can see the top of the spark plug 5 inches down. Using a 5/8 inch spark plug socket with a rubber 'holder' inside the socket to hold the plug, remove each plug. I had to use a 10-inch ratchet extension to provide sufficient clearance. I know it sounds goofy using a standard size socket on a metric car, but it is what it is. I make sure I get each coil back to its original location, but it really does not matter as they are all the same. Since the heads are aluminum and the spark plugs are stainless steel or monel/nickel, you have to be careful not to ruin the threads on the heads. I ONLY remove the plugs when the engine is cold. Apply some high temperature anti-seize only to the threads on the new plugs and install to 18ft-lbs of torque. Slip the coil back in place, attach the connector, install and tighten the bolt and you are done with that plug. Repeat for each plug. Re-install the air intake assembly and snap down the two latches and you are through with that side.

The driver's side is more difficult as there are things in the way. I had to remove one bracket (held in place with 2 12mm bolts) and disconnect a rubber hose underneath that bracket (it just slipped off with little effort - no tools required) in order to provide sufficient room to remove the coils. This is not as bad as it sounds, and I had both removed in under 2 minutes. Now you have access to the coils and plugs and can repeat the process. Go slow, take your time, don't get anti-seize on the plug firing tip, use a torque wrench if you have access to one. Replace the hose and the bracket and you are done.

Total time is 1 hour if you are not mechanically inclined, 30 minutes if you are.

Posted on Jul 20, 2009

c17hydro
  • 2984 Answers

SOURCE: firing diagram for a 87 olds delta 88 3.8

1987 Oldsmobile Delta 88
3.8 liter V-6 VIN "3" Identifying Ignition Types I and II


119d8a7.gif
On Type II coil packs, the coils can be replaced separately and the ignition wires are all on the same side of the coil pack.

With Type I Ignition

c6cc640.gif
With Type II Ignition

7722088.gif

Posted on Aug 28, 2009

jeff_drakesr
  • 155 Answers

SOURCE: need firing order for a toyota 4 runner 1996 6

Here is the Firing Order.

6dcb9b7.gif
Good Luck and have a grt day.

Posted on Apr 01, 2010

ZJLimited
  • 17970 Answers

SOURCE: 2000 olds alero v6 spark plug firing order diagram

2000 Oldsmobile Alero 3.4 liter V-6 VIN "E"

488b39c.gif


Hope helps (remember rated this).

Posted on Jul 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

If i have a 1996 chevy cavalier i have the firing order for the spark plugs but need the order for the distributor or ignition coil


Firing Orders
  • Sending Units And Sensors
  • Starting System
  • GM Cavalier/Sunfire 1995-2000 Repair Guide

    FIRING ORDERS

    Print
    See Figures 1 and 2
    To avoid confusion, remove and tag the spark plug wires one at a time, for replacement.
    If a distributor is not keyed for installation with only one orientation, it could have been removed previously and rewired. The resultant wiring would hold the correct firing order, but could change the relative placement of the plug towers in relation to the engine. For this reason it is imperative that you label all wires before disconnecting any of them. Also, before removal, compare the current wiring with the accompanying illustrations. If the current wiring does not match, make notes to reflect how your engine is wired.


    0900c1528003cbe2.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Fig. 1: 2.2L (VIN 4) Engine Firing Order: 1-3-4-2 Distributorless Ignition System

    Apr 16, 2013 | 1996 Chevrolet Cavalier

    1 Answer

    Spark plug wire diagram 1996 4 runner


    http://www.autozone.com/autozone/repairinfo/specifications/specificationsMain.jsp?childCatName=Firing+Order&childCatId=26200242&categoryNValue=26299999&categoryNameForTitle=Ignition+and+Tune+Up&categoryName=IGNITION+AND+TUNE+UP&childCategoryNameForTitle=Firing+Order

    Nov 08, 2012 | Toyota Cars & Trucks

    1 Answer

    Firing order for 2002 toyota runner


    The firing order is 1-2-3-4-5-6 but it uses direct ignition so it has a coil for each spark plug.
    The cylinders on the passenger side are 1-3-5 and the driver side is 2-4-6.

    Aug 19, 2012 | 2002 Toyota 4Runner

    1 Answer

    Need wire diagram for 99 durango firing order


    FIRING ORDERS printpage_icon.gif

    Before carrying out extensive tests to isolate poor running problems, check connections of spark plug wires. This is especially important if plugs, wires, distributor, etc., have been disturbed recently for service. Obviously, this is not applicable to the wireless 4.7L engine.

    NOTE To avoid problems, remove and tag the spark plug wires one at a time to ease reinstallation.
    For vehicles with an extensive service history, keep in mind that the distributor could have been removed previously and rewired. The resultant wiring would hold the correct firing order, but could change the relative placement of the plug towers in relation to the engine. For this reason, it is very important that you label all wires before disconnecting any of them. Also, before removal, compare the current wiring with the accompanying illustrations. If the current wiring does not match, make notes in your book to reflect how your engine is wired.


    0900c152800c0637.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. 2.5L Engine Firing Order: 1-3-4-2 Distributor Rotation: Clockwise


    0900c152800c0638.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. 3.9L Engine Firing Order: 1-6-5-4-3-2 Distributor Rotation: Clockwise


    0900c152800c0639.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. 5.2L and 5.9L Engines Firing Order: 1-8-4-3-6-5-7-2 Distributor rotation: Clockwise


    0900c152800c063a.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. 4.7L Engine Firing Order: 1-8-4-3-6-5-7-2 Distributorless Ignition


    0900c152800c063b.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. 8.0L Engine Firing Order: 1-10-9-4-3-6-5-8-7-2- Distributorless Ignition
    icn_arrow.gifBack to Top

    Dec 30, 2010 | Dodge Durango Cars & Trucks

    1 Answer

    Fireing order


    the firing order is 123456 pretty easy, but i think what you want is spark plug location on the coil packs, so lets start with cylinder placement. starting at the front of the engine the end with the belt the three cylinders closest to the radiator are 2 4 6 the cylinders at the back of the engine are 1 3 5 the spark plug wire location is from the front of the coil pack( fount of engine ) 1 4 6 3 2 5......HAVE FUN

    Dec 13, 2010 | 2000 Pontiac Montana

    1 Answer

    Where can i have a spark plug's schema of the pontiac transport 1994 3.1L ?


    If you're looking for the firing order diagram, this is it:

    FIRING ORDERS NOTE: To avoid confusion, remove and tag the spark plug wires one at a time, for replacement. If a distributor is not keyed for installation with only one orientation, it could have been removed previously and rewired. The resultant wiring would hold the correct firing order, but could change the relative placement of the plug towers in relation to the engine. For this reason, it is imperative that you label all wires before disconnecting any of them. Also, before removal, compare the current wiring with the accompanying illustrations. If the current wiring does not match, make notes in your book to reflect how your engine is wired. Fig. 1: 3.1L Engine Firing Order: 1-2-3-4-5-6 Distributor Rotation: Clockwise 91092g13.gif
    Fig. 2: 3.4L Engine Firing Order: 1-2-3-4-5-6 Distributorless Ignition 91092g14.gif
    Fig. 3: 3.8L Engine Firing Order: 1-6-5-4-3-2 Distributorless Ignition 91092g18.gif
    prev.gif next.gif

    Oct 17, 2010 | 1994 Pontiac Trans Sport

    1 Answer

    When I replace the spark plug wires on my 2000 4runner how do make sure that the wires are in the correct order


    Okay, on the photos I am posting, pick the size of motor that you have....since you didn't post it. When you find the right photo of your motor, the numbers on the engine correspond to the number of the spark plug that goes to the coil...1 to 1, 2 to 2 and so on. This is your firing order and will ensure you have the proper spark plug firing from the correct point:


    1a3d6bb.gif
    1FZ-FE engine Firing order: 1–5–3–6–2–4Distributor rotation: counterclockwise


    86807a1.gif
    5VZ-FE engine Firing order: 1–2–3–4–5–6Distributorless ignition system


    fe73fe6.gif
    2RZ-FE and 3RZ-FE engines Firing order: 1–3–4–2Distributor rotation: clockwise


    ecb67ba.gif
    2RZ-FE and 3RZ-FE engines Firing orders: 1–3–4–2Distributorless ignition system


    09d7f31.gif
    2UZ-FE engines Firing order: 1–8–4–3–6–5–7–2Distributorless ignition system

    Aug 12, 2010 | Toyota 4Runner Cars & Trucks

    1 Answer

    Need to know the placement spark plug wires 2001 chevrolet malibu


    do not have a diagram, but heres the firing order. 1-2-3-4-5-6, 1-3-5 is in back, # 1 is closest to alternator. from left to right, or facing engine from front 2-4-6 is in front. 5-2-3-6-4-1 is coil pack, from left to right (facing from front of engine).

    Jul 30, 2010 | 2001 Chevrolet Malibu

    1 Answer

    How to change spark plugs in 2.5 misubishi in a 1998 sebring


    Remove boot to spark plug using a boot puller. Unscrew spark plugs using a spark plug socket, extension, and ratchet.
    Do them one at a time to avoid confusion. Installation is the reverse of the removal.
    --- FIRING ORDERS NOTE: To avoid confusion, remove and tag the spark plug wires one at a time, for replacement. If a distributor is not keyed for installation with only one orientation, it could have been removed previously and rewired. The resultant wiring would hold the correct firing order, but could change the relative placement of the plug towers in relation to the engine. For this reason, it is imperative that you label all wires before disconnecting any of them. Also, before removal, compare the current wiring with the accompanying illustrations. If the current wiring does not match, make notes in your book to reflect how your engine is wired. Fig. 1: 2.0L and 2.4L Engines Firing Order: 1-3-4-2 Distributorless Ignition System 90902g01.gif
    Fig. 2: 2.5L Engine Firing Order: 1-2-3-4-5-6 Distributor Rotation: Counterclockwise 90902g02.gif
    prev.gif next.gif

    Jul 19, 2010 | 1998 Mitsubishi Galant

    1 Answer

    2000 mitsubishi eclipse v-6 spark plug wire placement


    For the 3.0L V6:
    Firing Order:
    1-2-3-4-5-6
    Cylinders:
    .....(back)
    1.......3......5
    2.......4......6
    ....(front)
    Distributor:
    ...(back)
    4....5....6
    o....o....o
    /////////////
    \\\\\\\\\\\\\
    o....o....o
    3....2....1
    ..(front)

    Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

    Mar 03, 2010 | 2000 Mitsubishi Eclipse

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    14 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8210 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...