Question about 1997 Mazda Millenia

Open Question

I'm getting code number: IS09141 I would like to know what it means so I can fix it??

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does a exclamation mark mean when flashing


Sandra, I presume you see some flashing on the dash cluster panel. A check engine command with exclamation. If car runs, take to an auto parts store and they have a hand held computer device that can read the code fault problem for you. They don't charge anything. Write down the code fault number for later. They will tell you what is dysfunctional causing the flashing. They can usually recommend some place to have it fixed. Knowing what part needs to be replaced before you go to fix it shop will keep you from getting something done not needed. Get second opinion/cost for repair before having done if you can by telling them the fault code and part that needs replacing.

Apr 13, 2015 | 2000 Mercury Sable

1 Answer

Is09141 fault code


ise the following website for to see what going on.
www.automecanico.com or www.autoelectronico.com
use your browser and translate the web page.
God bless you

Jun 11, 2013 | Cars & Trucks

2 Answers

1999 3.8 v6 camaro hesitates when accelerating slowly,just replaced plugs,wires and o2 sensor. service engine light blinked 4 times then stayed on when it started hesitating.gradually gotten worse over...


need to have car scanned most auto stores offer this service for free the code will give u a place to start so u can repair or service problem hesitation can be caused by a number of things example ---fuel filter-fuel pump problem--egr valve--air filter- a number of electrical sensors going bad ect,ect...thats why have trouble light scanned to help in solving problem

Jun 12, 2011 | 2002 Chevrolet Camaro

1 Answer

DTC shows up on computer at auto zone as a bad code and i dont know what DTC means so i cant fix it if i dont know what it means so my question to you is what in the world does DTC mean ? Im working on a...


DTC stands for Diagnostic Trouble Code. My question is why did you have the vehicle checked out in the first place? Is the check engine light on? What was the code number and did it start with P0 or P1. If you don't remember then have the code(s) cleared and operate the vehicle until the code(s) reappear. The code or codes can help you to determine where to start looking.

May 14, 2011 | Chevrolet C3500 Cars & Trucks

1 Answer

My light has just come on my 2005-what does this mean? What approx. would be the cost? Where do I take it to?


The means, that the computer pick up a bad signal, from one of your engine sensor's. take it to any auto parts or Autozone, where they will do a free code reading, without knowing the code number, can't tell you what it would cost to repair, get back with us with the code number, so we can help you diag. your trouble code

Aug 20, 2010 | Chrysler 300 Cars & Trucks

1 Answer

The engine light came on recently in my 2007 Jeep Liberty. Everything seems normal, engine sounds good, it is not overheating, etc...could it be something easy to fix?


This may or may not work depending on the feature install in your vehicle.
To find out, put you Jeep in park, turn the ignition off, now with our starting the engine turn the ignition on,off,on,off,on,off,on this must be completed in 10 seconds. If you have a digital odometer the number should change shortly, the first number will be 12, each number will flash 3 times. The last number will be 55 which means "end of codes". If you don't have a digital odometer it will flash the codes on your check engine light.
If this works write the codes down and I can tell you what they mean. If it doesn't work then as far as I know your vehicle requires a code reader in order to read the codes in your Jeeps computer.
If you want you can take your Jeep to Autozone and they will read the codes for you.

Jun 14, 2010 | 2007 Jeep Liberty Sport

2 Answers

Peugeot 206 radio Error 2, what does this mean?


i don't know what error 2 is. It might mean that you tried too many attempts to enter the code, causing the radio to 'lock up'. When this happens, some radios 'auto clear' the error code after a fixed period of time (anywhere from 3 hours to a couple of days). Others can't be cleared without sending the radio back to the manufacture (but try simply disconnecting the battery, and reconnecting it, first) 
Assuming that you can get back to the position where you can enter the code, here's how to do it. I'll use the code 4968 for my example: 
Press button 1, 4 times 
Press button 2, 9 times 
Press button 3, 6 times 
Press button 4, 8 times 
Press button 6.

try leaving your ignition on for an hour or so and see if the error 2 message changes to the option where you have to input a code.

check you peugeot manuals to see if the previous owner has noted the code down if not hopefully you should have a stereo manual whihc will have the serial number on it .if not then you will have to remove the stereo and get the serial number off the back.
if you take the serial and logbook to a peugeot dealers they will beable to give you a code usually free.

let us know how you get on and please rate 

May 06, 2009 | 2005 Peugeot 405

3 Answers

Error code 1684


Error code Number P1684 Battery Disconnected Within Last 50 Starts. Check battery and connections.

Nov 16, 2008 | 1999 Dodge Intrepid

3 Answers

Radio error message


If it has a CD player it means it is jammmed have the dealer correct the issue first and make sure you have the radio code for future battery changes or battery disconnects its available only with the dealer and proof of ownership

Nov 04, 2008 | 2005 Honda CR-V

1 Answer

Codes


OK. The Code bank 1 or 2, have to be acompained with a especific code number.
Because Bank 1 or 2, is Left side or Right side.
On windstar Bank 1 is at the firewall side, and Bank 2 is at the radiator side.
But the number of the Code will give the especific problem on any of the Banks. After that you gonna know what you have to fix.

OK I hope this information will help on your question.

Thank's

Jul 10, 2008 | 2001 Ford Windstar

Not finding what you are looking for?
1997 Mazda Millenia Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...