Question about 2005 Dodge Neon

Open Question

2005 neon dodge code P2096 - 2005 Dodge Neon

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 170 Answers

SOURCE: can you tell me what

Follow this link. http://www.obd-codes.com/trouble_codes/dodge/

Posted on Sep 03, 2010

johnjnail
  • 1702 Answers

SOURCE: I have these codes coming

code #0406 = egr position sensor circuit high ( stuck egr valve or bad egr sensor most likely sensor )

code #2096 = downstream fuel trim system lean ( see next code )

code #0137 = O2 sensor bank 1 sensor 2 circuit low ( replace rear O2 sensor driver side )

code #2299 = brake peddle position/accelerator pedal position incompatible. ( hav you been power braking this truck? ) ( brake light was on wile accelerator was being pushed )

Posted on Mar 17, 2011

ZJLimited
  • 17970 Answers

SOURCE: Engine code P2096 for a 2005 Dodge Noen 2.0litre

P2096 is Post Catalyst Fuel Trim System To Lean Bank 1.
In most cases this code refers to a bad O2 sensor in the exhaust. Due to year etc, senor replacement. here is the technical info for the code. Indicating O2 sensor 1/2 meaning bank 1, sensor 2 plus shows other posssibles

SET CONDITION
If the PCM multiplies short term compensation by long term adaptive as well as a purge fuel multiplier and the result is below a certain value for 30 seconds over two trips, a freeze frame is stored, the MIL illuminates and a trouble code is stored. Two Trip Fault. Three good trips to turn off the MIL.

POSSIBLE CAUSES
Exhaust leak
Engine mechanical
1/2 O2 Sensor
(K141) O2 Sensor 1/2 signal circuit
(K299) O2 1/2 Heater control circuit
(K904) O2 Return downstream circuit
Fuel contamination

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. See: Initial Inspection and Diagnostic Overview\Initial Inspection

DIAGNOSTIC TEST
1. ACTIVE DTC

NOTE:
- Check the vehicle repair history. If the 1/2 O2 Sensor has been replaced make sure that the O2 sensor was properly installed and meets OEM specification.
- Check for contaminants that may have damaged the O2 Sensor: contaminated fuel, unapproved silicone, oil and coolant.

Ignition on, engine not running.
With a scan tool, read DTCs.

Q: Is the DTC active at this time?

YES: Go To 2
NO: Refer to the INTERMITTENT CONDITION Diagnostic Procedure. See: Component Tests and General Diagnostics Perform the POWERTRAIN VERIFICATION TEST. See: Verification Tests\Powertrain Verification Test


2. EXHAUST LEAK
Turn the ignition off.

WARNING: TO AVOID PERSONAL INJURY FROM THE EXHAUST SYSTEM BEING HOT, ALLOW THE EXHAUST TO COOL DOWN TO A SAFE TEMPERATURE BEFORE PERFORMING A PHYSICAL INSPECTION. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN PERSONAL INJURY OR DEATH.

Visually and Physically inspect the exhaust system for holes, cracks, and blockage in the exhaust system.

Q: Is the exhaust system is good condition?

YES: Go To 3
NO: Repair or Replace as necessary. Perform the POWERTRAIN VERIFICATION TEST. See: Verification Tests\Powertrain Verification Test


3. ENGINE MECHANICAL
Check for any of the following conditions/mechanical problems.
AIR INDUCTION SYSTEM - must be free from leaks
ENGINE VACUUM - must be at least 13 inches in neutral
ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
ENGINE EXHAUST SYSTEM - must be free of any restrictions or leak
ENGINE PCV SYSTEM - must flow freely
TORQUE CONVERTER STALL SPEED - must be within specifications
POWER BRAKE BOOSTER - no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR - plugged or restricted injector; control wire not connected to correct injector

Left side exhaust, 2nd O2 sensor back just after cat converter

zjlimited_822.gif

- Raise and support vehicle.
- Disconnect wire connector from O2S sensor.

CAUTION: When disconnecting sensor electrical connector, do not pull directly on wire going into sensor.

- Remove O2S sensor with an oxygen sensor removal and installation tool.
- Clean threads in exhaust pipe using appropriate tap.

INSTALLATION
Threads of new oxygen sensors are factory coated with anti-seize compound to aid in removal. DO NOT add any additional anti-seize compound to threads of a new oxygen sensor.

Install O2S sensor. Tighten to 30 N-m (22 ft. lbs.) torque .
Connect O2S sensor wire connector.
Lower vehicle.


Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa.

Posted on Nov 01, 2011

ZJLimited
  • 17970 Answers

SOURCE: 2005 Dodge Neon 2.0litre Engine Code P2096?

I suggest visit this link around the same code question: engine_code_p2096_2005_dodge_noen

Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa.

Posted on Nov 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 dodge neon will not go into passing gear no codes showing


you should check the kick down cable to see if it is disconnected or broke. it will be next to the throttle cable on the throttle body.

Sep 10, 2015 | Dodge Cars & Trucks

1 Answer

What does code p2096 mean for 2005 magnum SE?


P2096- Post Catalyst Fuel Trim Sys Too Lean Bank1... It could be the result of bad gas or if you used fuel with a higher content of Ethanol. It could also mean that the post cat. converter O2 sensor on the driver side is bad. I would try filling up with a good quality gas (minimal Ethanol content), disconnect the negative terminal on the battery for a minute or so to reset the MAL (malfunction indicator light) and see if that takes care of it. If the code reappears, you may have a bad sensor, maybe ECU ECM PCM, worst case.... If you happen to need any info or ECU ECM PCM for this current vehicle (as they have a HIGH failure rate) or ANY other type of Car, diesel trucks small and big, SUV DIESELs ANYTHING etc, please call 888-672-4816 or 954-279-2040 and tell them Tim From FIXYA.COM sent you for FREE PROGRAMMING on YOUR NEW ECU ECM PCM DIESEL OR GAS COMPUTER!! Best Regards, -Tim

Mar 27, 2015 | 2005 Dodge Magnum SE

1 Answer

2005 Dodge Neon SXT 2.0L crankshaft position sensor location to replace


P0315 - Crankshaft Position System Variation Not Learned
P0335 - Magnetic Crankshaft Position Sensor Electrical Error China OBD2 car diagnostic tools wholesale on CareUCar

Mar 20, 2014 | 2005 Dodge Neon SXT

1 Answer

2005 Dodge Neon 2.0litre Engine Code P2096?


I suggest visit this link around the same code question: engine_code_p2096_2005_dodge_noen

Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa.

Nov 01, 2011 | 2005 Dodge Neon

2 Answers

I have these codes coming up on my 2005 Dodge Ram. 5.7 liter motor: P0406 P2096 P0137 P2299 Thank you.


code #0406 = egr position sensor circuit high ( stuck egr valve or bad egr sensor most likely sensor )

code #2096 = downstream fuel trim system lean ( see next code )

code #0137 = O2 sensor bank 1 sensor 2 circuit low ( replace rear O2 sensor driver side )

code #2299 = brake peddle position/accelerator pedal position incompatible. ( hav you been power braking this truck? ) ( brake light was on wile accelerator was being pushed )

Mar 17, 2011 | 2005 Dodge Ram

2 Answers

Check engine light comes on. odb2 code P2096 What does it mean


WHAT EXACTLY MEANS THE CODE P2096 AND HOW I SHOULD FIX IT CRYSLER 300 2010

Apr 24, 2010 | 2005 Chrysler Town & Country

1 Answer

How do I turn off the service engine code in my 2005 hyundai accent ..code p2096


The code.... P2096.... Post Catalyst Fuel Trim System Too Lean, Bank 2... If this has been repaired you can turn off the light with a scanner tool.....

Feb 12, 2010 | 2005 Hyundai Accent

1 Answer

P2096 Engine Code for a 2005 Caravan


P2096=Post Catalyst Fuel Trim System Too Lean Bank 1,
drivers side was too lean at one time and set code,You should hhave the code erased and see if it returns again,

Dec 28, 2009 | 2005 Dodge Caravan

Not finding what you are looking for?
2005 Dodge Neon Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...