Question about 2005 Toyota ECHO

Open Question

How to replace toyota echo blower resistor - 2005 Toyota ECHO

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 154 Answers

SOURCE: Blower motor has only low speed

You may need to get the correct resistor, as they are designed to only allow so much amperage to go through them. If it is getting very hot it is runnig to many amps through it. It will eventually blow and you will need to replace it anyway.

Posted on Jul 28, 2008

Ad
  • 102 Answers

SOURCE: In 2002 Toyota Echo, I need to replace blower

blower switch is your fan knob on dash. resistors are located under pass side dash next to blower motor. on alot of cars the blower will work on high speed and not the lower ones- this is a tell tale way to tell the resistor is no good. if this happens again after replacing resistor- ive seen the blower motor shorting out causing the resistor to go bad- then you would have to replace both.(this usually dosnt happen, most often the resistor alone fixes the problem..

Posted on Nov 28, 2009

  • 1 Answer

SOURCE: Toyota Echo heater fan runs on high only. I gather

Thanks, I found the answer on other sites.

Posted on Mar 02, 2010

  • 691 Answers

SOURCE: how do you replace the blower motor resistor in a

The resistor pack is almost always close to the blower. It needs air moving across it to keep it cool. It is usually installed into the duct with two small screws. It has a connector with about 5 -6 wires, and is about 3/4 inch wide, and about 3-4 inches long. Some can be a little difficult to get out due to clearance, and their shape.

Also, it could be the fan speed switch that's giving you problems.

Posted on Aug 31, 2011

  • 691 Answers

SOURCE: blower resistor Toyota Tacoma 2007 where is locater

Might be the Resistor pack located close to the blower. Could be under the dash or under the hood, but always close to the blower itself. Usually has a flat connector with 4 or 5 wires, and two small screws holding in the duct. It may be a crispy critter. It happens... The blower moves air across it to keep it cool. The blower motor may be bad as well, or possibly the fan speed switch. May very well be the fuse for the blower as well. The blower connector may be loose. Let me know what you find.

Posted on Dec 02, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to troubleshoot low air flow from the vents on a 2000 Toyota Echo?


check the polartily at the fan & make sure the fan is turning the correct way
but first check the cabin filter/air intake is no blocked

Apr 04, 2014 | Toyota ECHO Cars & Trucks

2 Answers

Video how to to change the blower fan on toyota Echo 2002


This blower fan in the 2002 Toyota Echo is located under the dashboard on the passenger side of the vehicle. It is covered by a plastic panel that snaps into place and shields the motor from accidental damage. When the blower fan fails, air will not come out of the vehicle's vents despite the fan control speed setting. A replacement blower motor can be purchased from a certified Toyota dealerships or any auto parts store
.


read more: obd2 car diagnostic

Aug 05, 2012 | 2002 Toyota ECHO

1 Answer

How do you replace the blower motor resistor in a 2001 toyota echo, blower only works when set to full speed leads me to believe it is the resistor from searching information, just need to figure out how...


The resistor pack is almost always close to the blower. It needs air moving across it to keep it cool. It is usually installed into the duct with two small screws. It has a connector with about 5 -6 wires, and is about 3/4 inch wide, and about 3-4 inches long. Some can be a little difficult to get out due to clearance, and their shape.

Also, it could be the fan speed switch that's giving you problems.

Aug 31, 2011 | 2001 Toyota Echo

1 Answer

Heating and cooling works only when set to high


Resistors or Blower motor on/off switch.
I believe the resistors are found by the blower motor.

Apr 12, 2010 | 2001 Toyota Echo

1 Answer

Heater blower motor not working on 2003 echo


no power at the resistor of the blower fan 2003 toyota ecko

Dec 01, 2009 | 2002 Toyota ECHO

1 Answer

In 2002 Toyota Echo, I need to replace blower motor. There is also a resistor and a ''blower switch'' in a manual, but no explanation of the blower switch. Is this just the 'fan switch' on the dash. ...


blower switch is your fan knob on dash. resistors are located under pass side dash next to blower motor. on alot of cars the blower will work on high speed and not the lower ones- this is a tell tale way to tell the resistor is no good. if this happens again after replacing resistor- ive seen the blower motor shorting out causing the resistor to go bad- then you would have to replace both.(this usually dosnt happen, most often the resistor alone fixes the problem..

Oct 17, 2009 | 2002 Toyota ECHO

1 Answer

Can't locate the resistor blower under the dash on the passenger side to replace it. can you help?


1. REMOVE GLOVE COMPARTMENT DOOR

2. REMOVE ENGINE (and ECT) ECU
(a) Disconnect the wire harness clamps.
(b) Disconnect the connectors.
(c) Remove the 2 bolts and engine (and ECT) ECU.
3. Two way flow heater models only:
REMOVE AIR DUCT (Motor cover)
(a) Disconnect the control link.
(b) Disconnect the connector clamps.
(c) Remove the screw.
(d) Release the claw and remove the air duct.
4. REMOVE BLOWER RESISTOR
(a) Disconnect the connector.
(b) Remove the 2 screws and blower resistor.
5. INSPECT BLOWER RESISTOR RESISTANCE
Tester connection Condition Specified condition
1 − 3 Constant Approx. 0.4 ω
1 − 2 Constant Approx. 1.5 ω
1 − 4 Constant Approx. 2.8 ω
If resistance is not as specified, replace the blower resistor.
6. INSTALL BLOWER RESISTOR
7. Two way flow heater models only:
INSTALL AIR DUCT
8. INSTALL ENGINE (and ECT) ECU
9. INSTALL GLOVE COMPARTMENT DOOR

Mar 08, 2009 | 2003 Toyota ECHO

Not finding what you are looking for?
2005 Toyota ECHO Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...