Question about 2001 Hyundai XG300

2 Answers

Hyundai Grandeur stops at lights or when moving slow

I have got new Camshaft sensors, some Oxygen Control sensors, and yet the car stops. The check engine light turns on and then the car just shuts off. All i have to do is to wait like 30 secs and it starts again. Some times the check engine light does not turn on for days and some times, it lights up ten times and car stops all the tjmes. The problem started when I changed the spark plugs at Hyundai service centre. The guy says he cannot find any problem with it.

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

To rahiherman I had the same problem for a couple of month's when an nrma technician told me to look at the crank angle sensor and sure enough that seems to have fixed it, so have your mechanic check it out

Posted on Jun 27, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

What guy?... the Hyundai Technician?... Take it back to them and tell them to FIX it! The problem didn't start until you had THEM do a TUNE UP!... You do still have the receipt.. right?

Posted on Jun 25, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

PO-139 I had that sensor change 3 weeks ago and the check engine light came on again this morning.Thanks

Probably replaced a good sensor. This codes could be from a bad sensor, a vacuum leak, or an exhaust leak before the sensor.

Dec 01, 2015 | 2006 Hyundai Tucson

1 Answer

Hyundai grandeur won't start 1999

have you check cam timing, has the timing belt jumped or has it broken and need replacing. does this have an anti-theft system on it and if so is it activated to cause no start. are the injectors working, have you check for codes in the computer is there is a problem with the computer. just some things to look into.

Aug 31, 2014 | 2005 Hyundai Grandeur

1 Answer

Hyundai motor problem warning motor light

run fault codes to check for failed sensor.

Nov 30, 2013 | Cars & Trucks

1 Answer

Hyundai grandeur 2000 starts then stops straight

It's the sensor, it should be reprogrammed.

Aug 09, 2017 | Hyundai Cars & Trucks

1 Answer

Ck engine light stays on. Autozone says it is the camshaft sensor. I have pulled it apart and cleaned it with a qtip and alcohol, reset the battery and it has worked great. Now, it doesn't and my...

Gas milage (economy) is dependent upon the O2 Snsr's (oxygen Sensors) input to the ECU (Engine Control Unit). The cam position sensor, if malfunctioning, it should be replaced (cleaning it doesn't repair the problem which exists inside the component/sensor). Before you start throwing money after parts, Have a qualified/certified Hyundai Service Technician properly diagnose this issue.

Sep 10, 2011 | 2006 Hyundai Elantra

1 Answer

Starts and switch of automatically problem code P 1275 if camshaft sensor is pulled out vehicle stays idiling but still revs up slow. Engine light stays on.

P1275 Aging of Oxygen Sensor Ahead of Catalytic Converter (Cylinders 1 - 3) - Below Lower Limit

The diagnosis of "oxygen sensor aging" helps to identify oxygen sensors that exceed emission limits because of aging.
During the diagnosis of oxygen sensor aging, the DME control module monitors the period of the sensor signal. With an old sensor, the duration of the period is too long, i.e. it is more difficult for the sensor to diffuse oxygen into the exhaust gas. Reasons for this could be frequent driving in the lower load range (city driving, short distances, etc.) or a contaminated sensor.

Bottom line - you need to replace that O2 sensor.
hope help.

Jul 06, 2011 | 2004 Nissan Pathfinder

1 Answer

I washed the engine, then cruise control stopped functioning, before that rpm needle went mad and fluctuated from 0 to max on and off. I think there is a short circuit , but don't know where to find or...

If you have an after-market cruise control system, you'll need the specs from the company that manufactured it. Otherwise, it's guess work. Does the Check Engine light come ON when this happens? Whenever the "Check Engine" light comes on, there is always a DTC (Diagnostic Trouble Code) stored in the ECM (Engine Control Module). You'll need an OBDII (On-Board-Diagnostics) scanner to retrieve any codes recorded/set in ECM. See if there's a P0500 DTC. I imagine the cruise control system uses this signal as well as the Speedo.
P0500 Vehicle Speed Sensor Malfunction
The vehicile's speed sensor is on the transmission almost directly below the throttle body
It is a three pin connector (pin 1=power-12VDC, pin2=ground, & pin3=signal).


Apr 05, 2009 | 2001 Hyundai XG300

1 Answer

Hyundai Grandeur 2000

Do a tune up and if it's still a problem check your Iac or tps idle air control or throttle position sensor

Feb 05, 2018 | Hyundai XG300 Cars & Trucks

Not finding what you are looking for?
2001 Hyundai XG300 Logo

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides