Question about 2007 Jaguar XKR Convertible

Open Question

Key fob is stuck in console backwards and the rear lights are on how do you remove key

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98volvo c70 how do i open the stuck trunk when key fob, keys, or trunk release button will not work


I don't work on these, but , remove the rear seat, bolted in. or drill out the lock until it can be turned. Being a 98, you will still have to climb in it and release the latch by hand. And it is most likely covered. Break the cover off.

Sep 22, 2016 | 1998 Volvo C70

1 Answer

How can I manually unlock my rear door if the actuator is bad. My rear fate door is stuck in the lock position and I can not unlock it with the key fob or auto lock. 2007 rav 4


Access the gate latch from the inside by removing the interior door panel. Once the gate is open, replace the actuator and you should be good to go.

Jul 19, 2014 | 2007 Toyota RAV4

1 Answer

Why is the red light flasing on key fob of 2003 hyundai coupe?


where are you, your key, in kitchen, standing near car, or in car or key inserted in the ignition, I will answer , IN KITCHEN.
the operators guide, lost>? it might the first clue.
http://justgivemethedamnmanual.com/hyundai/hyundai-tiburon-owners-manual/
the fob has a light. ok , Factory Fob, or aftermarket?

the car came with 2 fobs, new, so do both fail or act odd like this.
id bet not.
and the fob has and LED lamp , if it sticks on , that means'
the FOB is no good, the switches are stuck, ON.
time to buy a new FOB or get McGiver fix yours at x2 new cost.
you can also replace the battery and how that fixes it and or clean
the insides, of fob. at same time
page 1.5 above covers the fob.

the lamp flashes when the button is pressed.
so the button is stuck,, broken./


Jul 02, 2014 | 2003 Hyundai Tiburon

1 Answer

Peugeot 206 key fob


Try with brand new key fob battery and see.If that helps.
Otherwise May be keyfob needs to be reprogrammed.

KEYFOB PROGRAMMING


Keyfob remote reprogramming is not very difficult but on some cases it can be done by dealer service tools.

If the remote s faulty then key fob will not get programmed.

Insert the key in ignition. Turn the key to on position, and cycle the key three times off-on-off-on-off-on. Then with the key fob remote select your remote and then try to operate the vehicle with remote.

These are just the basic procedure, but sometimes it will not help.

On that case dealer is the only option.


---------

There are few much related troubleshooting links mentioned below for remote key fob reprogramming. I suggest you to go through the list and click the link below to go through its details and procedure: -------

2009 Toyota Highlander: Smart Key Not getting Detected?

http://whatisbyme.blogspot.in/2012/05/2009-toyota-highlander-smart-key-not.html


----------

2007 Toyota Prius: Reprogram Remote Keyfob?

http://whatisbyme.blogspot.in/2012/05/2007-toyota-prius-reprogram-remote.html

-----------

Pin that holds the flick key part to the key fob?

http://whoisbyme.blogspot.in/2012/07/pin-that-holds-flick-key-part-to-key-fob.html

-------------


2006 Toyota Hilux: Programming New Key?

http://technoanswers.blogspot.in/2012/04/2006-toyota-hilux-programming-new-key.html

----------

Where is Key chip memory located on 2004 ford Freestar?

http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html

----------

Ford Keyless Remote Fob Reprogramming?


http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html

----------

After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?

http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html

-----------

Audi A8 Key Fob Programming?


http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html

----------------

Oldsmobile Aurora Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html

-------------

Buick Lesabre Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html

---------------

Keyfob remote not working on 2003 Ford E350 Econoline?

http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html

-----------

KeyFob will open the doors but not start on BMW?

http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html

------------

Mitsubishi Car Key Not getting detected after replacing ECM

http://repairhelpcenter.blogspot.com/2012/11/mitsubishi-car-key-not-getting-detected.html

-----------

Key Fob will not lock and unlock doors?

http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html

-------------

2000 Jeep Cherokee Limited: KeyFob Remote Not Working?

http://schematicsdiagram.blogspot.in/2012/06/2000-jeep-cherokee-limited-keyfob.html

-----------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

-----------

Theft indicator not letting car to start?

http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html

-------------

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html

--------------


These details will help.

Thanks.

Nov 28, 2012 | Peugeot Cars & Trucks

1 Answer

Replaced chip on key on 91 DTS and car lost all power while driving. It shut down and nothing works.


There are 4 methods for programming key fobs. Up to 4 key fobs may be programmed to the remote control door lock receiver (RCDLR). Each programmed key fob is given a position of #1-#4 in the RCDLR memory.
Method 1 - Key Fob Quick Learn This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicles mechanical key.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4).
Place the replacement key fob in the console fob pocket with the buttons facing forward.
A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED.
If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion of the ignition switch to exit programming mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 2 - Key Fob Slot Programming

This procedure will add or replace a key fob. Method 2 allows you to choose which location (slot) the unprogrammed fob will be learned to. If you are replacing a key fob, this method will erase the previously known key fob programmed to that particular slot. This procedure requires that you have a known good key fob, a replacement key fob, the vehicle mechanical key, and a scan tool.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the DIC will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Install a scan tool.
Use the scan tool, to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 4-8, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 3 - Key Fob Auto Learn

This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming with Method 3. If the RCDLR recognizes a known good key fob during Method 3 programming, the programming mode will resort to Method 1.


The vehicle must be OFF.
Place the replacement key fob in the console pocket with the buttons facing forward.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time.
When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
Repeat steps 5-7 two more times, for a total of 30 minutes.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode.
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 4 - Service Programming System Fob Programming

This procedure is a 10-minute relearn procedure using the Techline Terminal with SPS software. Once the 10-minute timer has expired, the fobs can be programmed similar to Method 2 using slot programming. A scan tool, Techline Terminal, and a replacement key fob are required to perform this procedure.

Place the vehicle in the Vehicle On, Engine Off mode.
Connect a scan tool to the vehicle.
Insure that all power consuming devices are turned OFF on the vehicle.
With a scan tool, select Request Info under Service Programming System and follow the scan tool on-screen instructions.
Disconnect the scan tool from the vehicle and connect the scan tool to a Techline Terminal with the current Service Programming System (SPS) software.
Turn the vehicle OFF.
On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions. Ensure the correct programming procedure is selected based on component being replaced or programmed. See Important above.
Disconnect the scan tool from the Techline Terminal and re-connect the scan tool to the vehicle.
With a scan tool, select Program ECU under Service Programming System.
At this point the scan tool must remain connected for the duration of the 10 minute relearn procedure.
When the 10 minute relearn procedure has completed, use the scan tool to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 12-13, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.

Oct 26, 2011 | 2006 Cadillac DTS

1 Answer

My battery is dead and I was told of a key inside of the remote to get in above the license plate key hole, but I can't find the key inside the remote. How can I get into my car?


A key should have come with the key FOB used to open rear hatch, lock glove box and center console. If don't have that key, you can jack car up, apply power to positive terminal of starter and a chassis ground, and the FOB should work.

Aug 11, 2010 | 2006 Chevrolet Corvette

1 Answer

How to replace a battery on my 2004 Audi key fob


there is a little notch on key, insert screw driver from the rear of the key lift the handle of the screwdriver upwards towards the front of the key (levering the rear part of the key backwards) when you get the rear part of the key out the lift off the top part and you will find the battery,

May 29, 2010 | 2004 Audi A6

2 Answers

Key fob wont work on my Peugeot Expert


Does the battery need changing on the key fob?
you can check by using you'r mobile phone cam & pointing the key fob (ultra violet bulb) at the lens when pressing the button, you should see the light flashing on the key fob looking through the camera, you can use any camera, most of them will see the light as it's out of our sight range but cameras pick it up.
If not then unscrew the key fob & split it carefully (use an old credit card not a knife or screwdriver) & change the battery.
If the fob work's then the problem is with the receiver, usually up by the rear view mirror.
Hope this help's !

Sep 21, 2009 | 2005 Peugeot 405

1 Answer

Rear door on 97 bravada can't be unlocked to open


No easy way to do this - you need to remove the inside door panel from inside the truck and manually release the lock. You didn't say where the wiring was burnt, but when the door is open test for power at the lock solenoid - if not there when unlock is pressed, inspect the wiring (particularly at the two rubber wire casings connecting the door to the frame). If it is there, the lock solenoid is stuck and may have to be replaced.

Oct 02, 2017 | 1997 Oldsmobile Bravada

Not finding what you are looking for?
2007 Jaguar XKR Convertible Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...