Question about Cars & Trucks

Open Question

Honda odyessey timing belt issues - Cars & Trucks

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jturcotte
  • 8574 Answers

SOURCE: My balance shaft belt broke

see diagrams from autozone.com. Cam sprocket has an "UP" label, but also 2 scribes on the sides to align to upper head surface. The critical part of the job is keeping tension on the side of the belt that is opposite from the tensioner as the tensioner is released onto the belt. The timing marks must be aligned when the job is done.

2bd7a51.jpg
4256a1c.gif To install:

  1. Install the camshaft timing sprocket so that the UP mark is up and the TDC marks are parallel to the cylinder head gasket surface. Install the key and tighten the bolt to 27 ft. lbs. (37 Nm).
  2. Install the crankshaft sprocket so that the TDC mark aligns with the pointer on the oil pump. Install the spacers with their concave surfaces facing in. Install the key. If equipped, install the TDC sensor assembly back into position before installing the timing belt.
  3. Install and tension the timing belt. Use a 6 x 1.0 mm x 25 mm bolt threaded through the cam belt tensioner plate to temporarily hold the tensioner.
  4. Temporarily install the crankshaft pulley and rotate the crankshaft counterclockwise 5-6 turns to be sure the belt is properly seated.
  5. Set the No. 1 piston at TDC for its compression stroke.



WARNING If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.

  1. Rotate the crankshaft counterclockwise so that the camshaft pulley moves only 3 teeth beyond its TDC mark.
  2. Loosen, then retighten the temporary cam belt tensioner bolt.
  3. If the rear balance shaft sprocket/gear case assembly was removed, perform the following:
    1. If the rear balance shaft was moved, rotate the balance shaft until the 6 x 1.0mm x 100 mm bolt can be installed into the maintenance hole to the scribed line.
    2. Align the notch of the balance shaft sprocket edge with the pointer on the gear case. Install the rear balance shaft sprocket/gear case assembly using a new O-ring coated with fresh engine oil. The balance shaft sprocket should be installed in the TDC position. The pointer on the gear should align with the pointer on the oil pump housing plate.
    3. Tighten the mounting bolts to 18 ft. lbs. (25 Nm).

  4. If the front balance shaft sprocket was removed, perform the following:
    1. Install a suitable and sturdy screw driver or drift through the maintenance hole in the shaft behind the sprocket to hold the front balance shaft.
    2. Install the front balance shaft sprocket and mounting nut. Torque the nut to 22 ft. lbs. (29 Nm).

  5. Make sure the balance shafts and crankshaft are in the TDC position.
  6. Remove the crankshaft pulley, and if removed, install the balance shaft belt drive sprocket.
  7. Install the balance shaft belt, making sure the balance shafts and sprockets are still in the TDC position.
  8. If removed, install the balance shaft belt tensioner and tension the balance shaft belt.
  9. Loosen, then retighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm).
  10. Remove the 6 x 1.0mm x 100mm rear balance shaft holding bolt.
  11. Temporarily install the crankshaft pulley and rotate the crankshaft 2 revolutions counterclockwise, stopping at TDC.



WARNING If any resistance is felt, stop immediately and determine the cause.

  1. Recheck that all of the TDC marks align for both the camshaft and balance shafts.
  2. Loosen, then retighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm).
  3. Remove the 6 x 1.0 mm x 25 mm bolt used to secure the camshaft timing belt tensioner.
  4. Remove the crankshaft pulley and install the lower cover.
  5. Install the crankshaft pulley, lubricate the bolt threads and both sides of the crankshaft pulley bolt with fresh engine oil and tighten the crankshaft pulley bolt to 181 ft. lbs. (245 Nm). Do Not use an impact wrench.
See Figures 19 and 20


087aa27.gif

              Fig. Fig. 19: Holding the rear timing balancer shaft-4-cylinder Odyssey



            811a2fe.gif

            Fig. Fig. 20: Aligning the front timing balancer shaft-4-cylinder Odyssey

            1. Install the upper timing cover and the valve cover. Be sure the seals are properly seated.
            2. Install the side engine mount. Tighten the through-bolt to 47 ft. lbs. (64 Nm). Tighten the mount nut and bolt to 40 ft. lbs. (55 Nm) each.
            3. Remove the floor jack.
            4. Install and tension the alternator belt.
            5. Install the power steering pump and tension its belt.
            6. Install the splash shields.
            7. Reconnect the positive and negative battery cables. Enter the radio security code.
            8. Check engine operation.

            Posted on Sep 20, 2010

            Ad
            reaperautomo
            • 206 Answers

            SOURCE: I can't find wha the gap shold be on the spark plugs for my 2005 honda odyessey

            The recommended spark plug gap for a 2005 Honda Odyssey is .044"

            Posted on Oct 16, 2012

            Add Your Answer

            Uploading: 0%

            my-video-file.mp4

            Complete. Click "Add" to insert your video. Add

            ×

            Loading...
            Loading...

            Related Questions:

            1 Answer

            I have a 2003 Honda Odyessey, The speedometer stopped working. So far I've changed the instrument cluster and the speed sensor, and the fuses. still no change. Anybody have any ideas on this?


            Hi, your vechicle has whats called a "vss"sensor. I.e. a vechicle speed sensor. Usually down on the tranmission,its what gives the ecm its info. I would check that. Hope that helps.

            Oct 30, 2016 | 2003 Honda Odyssey

            1 Answer

            How do I get a gas tank out of a 1996 honda odyessey


            Filler pipe?

            Wiring?

            Maybe it is just stuck, being held in place with a paint/sealer/underseal bond...

            Feb 22, 2016 | 1996 Honda Odyssey

            1 Answer

            Electrical issues


            It sounds like your not getting your 12 volts past the battery Chris.
            Check connections at battery and the other ends of the battery wires for corrosion or loose connections.

            Feb 03, 2014 | Honda Odyssey Cars & Trucks

            1 Answer

            I can't find wha the gap shold be on the spark plugs for my 2005 honda odyessey


            The recommended spark plug gap for a 2005 Honda Odyssey is .044"

            Oct 15, 2012 | 2005 Honda Odyssey

            1 Answer

            My 98 honda odyessey ran hot today and it has water getting in my oil what do I do?


            The most likely source of your problem is a leaking head gasket. To check it remove all spark-plugs, pressurize the cooling system and inspect each cylinder for signs of coolant.

            Jul 21, 2011 | 2003 Honda Odyssey

            1 Answer

            Locate the evaporator canister on 2003 honda odyessey


            It is on the driver's side of the car directly underneath the spot the driver's right knee occupies while driving. It has a black plastic stone shield in front of it. If you get on the driver's side of the van and face forward parallel to line of travel and get down on your hands and knees with your head lined up with the steering wheel---then look under and to your right and you'll see it.

            Feb 05, 2011 | 2003 Honda Odyssey

            1 Answer

            1997 Honda Odyessey does not start; solenoid bad?


            Does the engine crank? any sound at all? U might want to jump start using jumper cable as the battery might be weak.

            Apr 13, 2010 | 1997 Honda Odyssey

            1 Answer

            The key is stuck in the ignition in the Honda Odyessey 1998


            make sure your vehicle is in park. if the dash indicator says that it is, check the transmition linkage and make sure it is shifting the transmition lever into park. Good Luck

            Nov 15, 2009 | 1998 Honda Odyssey

            1 Answer

            The TCS light comes on in my 2000 HOnda odyessey and the RPMs gauge seems to be sticking thus, no acceleration.


            have to get it checked out.. the computer needs to be scaned.. 9 out of 10 times the computer says it needs a transmission.

            Sep 08, 2009 | 2000 Honda Odyssey

            1 Answer

            My 2004 odyessey has the "D" in gear selector Blinking


            That indicates there's an issue with the A/T and more then likely a trans code is stored

            Nov 29, 2008 | 2004 Honda Odyssey

            Not finding what you are looking for?
            Cars & Trucks Logo

            Related Topics:

            13 people viewed this question

            Ask a Question

            Usually answered in minutes!

            Top Cars & Trucks Experts

            yadayada
            yadayada

            Level 3 Expert

            76846 Answers

            Colin Stickland
            Colin Stickland

            Level 3 Expert

            22246 Answers

            Randy Ohler

            Level 3 Expert

            14585 Answers

            Are you a Car and Truck Expert? Answer questions, earn points and help others

            Answer questions

            Manuals & User Guides

            Loading...