Question about 1999 Peugeot 406

1 Answer

Where is the door sensor on a peugeot 406 interior light are staying on and door on screen is showing open

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 25 Answers

The sensor is actually a small black pressure key on the front inside part of the door and it is covered with rubber

Posted on Oct 02, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: peugeot 406 central locking

you need to reprogram the fob

Posted on Oct 07, 2008

pippall
  • 1486 Answers

SOURCE: 406 hdi pass door lock wont lock so car wont lock

Remove the door pannel and spray releasing oil over the central locking solinoid.That should sort it for you good luck.

Posted on Sep 02, 2009

  • 205 Answers

SOURCE: what is the antipullution fault on peugeot 406?

If you drive your car more likely for short distances then the regenerating process couldn't be started to clean the cloged particulate filter and finally your car's ecu show you a antipollution fault. Drive your car to a motorway or dual carriage way.

The temperature meter should be showing above 70°C when you begin with this process. If this is the case, slow down place 3rd gear and drive at 3000-3500 rev /min to let the ecu to kick the regeneration process. Keep driving car 15 minutes in this state will be enough to solve this problem.

Posted on Oct 27, 2009

  • 17 Answers

SOURCE: peugeot 406 estate 2l hdi, anti polution light on

it would never be 1000 euros!!!!!!!!!!!! it will be part of the exhaust system it cuts out because its causing pollution

Posted on Nov 15, 2009

  • 1 Answer

SOURCE: peugeot 406 hdi wipers problem

i have the same problem.Have u had any luck with urs yet???

Posted on Feb 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is coolant sensor on a peugeot 406 hdi please


I know this sounds weird, but check on the mirror housing( pass. side) it should be located in the mirror.

Jan 25, 2015 | 1999 Peugeot 406

1 Answer

Peugeot 406 manual


reset the light using a scanner and if it comes back on then the sensor was not the problem

May 21, 2014 | Cars & Trucks

2 Answers

Why does Door ajar light on dash stays on when driver's door is closed


Usually a sign the sensor in the latch has failed. The sensor is telling the body computer the door is still open.

May 20, 2014 | 2004 Honda Odyssey

1 Answer

Peugeot 406 central locken locks then unlocks


Hi. usually caused by faulty drivers door lock motor. It controls the rest so if it fails then it will stop the rest operating properly. check the wiring in the door shut loom for broken wires. Jon.

May 03, 2014 | 1999 Peugeot 406

2 Answers

Door is showing open and interior lights stay on....when door is closed properly!!


This is because the switch mechanism on the door frame has failed and needs to be replaced. Hence the switch remains on and power will continue to flow to the interior lights until you switch them to full manual mode. The door warning light will also show as open because the warning light is operated off the same switch.

Dec 21, 2012 | 1999 Peugeot 406

1 Answer

My 406 peugeot shows oil pressure insufficient on display, what is the cause


My 406 peugeot always go off after on my A/C it we show me oil pressure insufficient! Please what can I do?

Mar 09, 2012 | 1999 Peugeot 406

2 Answers

I need a fuse layout diagram for a peugeot 406


Please can you tell me what the fuse rating is for my electric sun roof?
The car is a peugeot 406 98

Sep 24, 2010 | Peugeot 405 Cars & Trucks

1 Answer

Peugeot 406 - interior fan on constantly


change the switch / balast resister

Feb 24, 2010 | 2005 Peugeot 405

1 Answer

Peugeot 406


Most likely the ECU (Engine Computer Unit) is responding to some duff sensor / loose cable / whatever ..

All modern engines have more sensors than you can shake a stick at, some positioned in the most inaccessible places, that can cause the most obscure problems imaginable (remember the Oxygen Sensor in the Exhaust manifold that was 'poisioned' by some dufff supermarket petrol ??)

It's a Peugeot garage computerised diagnostics job I'm afraid...

Dec 28, 2008 | 1991 Peugeot 405

1 Answer

Peugeot 406 break lights stay on all the time


you need to pull out the socket from the brake switch which is located under the brake pedal. If the lights go off than the switch is faulty. if the lights dont go off than there must be a shot in the wire.

Sep 14, 2008 | Peugeot Liberte Cars & Trucks

Not finding what you are looking for?
1999 Peugeot 406 Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...