Question about 1993 Jeep Wrangler

Open Question

How to replace 93 2.5 wrangler camshaft sensor

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a camshaft position sensor 1995 jeep wrangler, 6 cyl, 5 speed stick


Remove the distributor cap and rotor, lift the sensor out and drop in the new one.

Aug 16, 2013 | 1995 Jeep Wrangler

2 Answers

93 camry v4 code 14


camshaft position sensor not working located at the end of camshaft.take care.

Sep 23, 2012 | 1993 Toyota Camry V6

1 Answer

1997 jeep wrangler has a long start. I have changed the fuel pump, camshaft sensor. any other suggestions


There is a head temp sensor and intake air temp sensor, either of which could make the mixture too lean. Check them with an ohmmeter. Not sure the exact reading, but bad ones usually go 0 or infinite.

Apr 08, 2011 | 1997 Jeep Wrangler

1 Answer

I need to replace the cam sensor on my 97 jeep wrangler were do i find it in the motor..


For 1997 Jeep Wrangler 4WD 4.0L MFI 6cyl the Camshaft Position Sensor is located: Under hood, passenger side, front engine area, mounted on front of intake manifold

Hope helps (remember to rate this).

Oct 12, 2010 | 1997 Jeep Wrangler

1 Answer

93 jeep temp gauge not working


not sure what your asking

Dec 25, 2009 | 1993 Jeep Wrangler

2 Answers

Camshaft position sensor failure on Saab 2003 93


replace it. there is a connection or a short in the sensor that's throwing the code. Get your Saab parts at Carquest Auto Parts, They have a WORLDPAC division for all hard to find(and easy) parts. trust me, you will save a fortune on Saab, Mercedes, Volvo and other high end parts.

Aug 29, 2009 | 1994 Saab 900

1 Answer

2007 Jeep Wrangler Unlimited Sahara


SUBJECT:
Long Crank Time Due To Possible Contact Of Camshaft Sensor To Camshaft Gear
OVERVIEW:
This bulletin involves the replacement of the engine camshaft sensor.
MODELS:
2007 (JK) Wrangler
NOTE: This bulletin applies to vehicles equipped with a 3.8L engine (sales code
EGT).
SYMPTOM/CONDITION:
The customer may experience one of the following conditions:
a). Long engine crank time.
b). Two engine start attempts prior to engine starting.
c). Due to the “TIP Start Feature” on automatic transmission equipped vehicles, once the
ignition key / switch has been released from the “START” position, the starter may stay
engaged for up to 10 seconds while the engine attempts to start.
The above conditions may be due to the position of the camshaft sensor to the camshaft
gear. The sensor spacer gasket may have come loose during engine assembly and
caused the camshaft sensor to be adjusted too close or in contact with the camshaft gear.
DIAGNOSIS:
If the above condition is present perform the Repair Procedure.
PARTS REQUIRED:
Qty. Part No. Description
1 04686353 Sensor, Camshaft

Jul 12, 2009 | 2007 Jeep Wrangler Unlimited Rubicon 2...

1 Answer

My fuel ecu fuse keeps blowing?


Unplug the O2 Sensor and see if it blow again. If it does not the sensor is faulty. Replace with a new one. BTY its in the exhast system.

Jun 13, 2009 | 1993 Jeep Wrangler

1 Answer

93 wrangler no spark


I'm certain that there is an "official" test for this sensor. I generally quick check by attaching a volt meter set to millivolts to the sensor leads and check for a pulse voltage when cranking. If in doubt and you don't want to spend big$ on the part, you can get an entire distributor at a scrap yard likely for half of the price of the new sensor.

Jun 11, 2009 | 1993 Jeep Wrangler

Not finding what you are looking for?
1993 Jeep Wrangler Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...