Question about 1999 Ford Windstar

Open Question

Rear license plate light not working - 1999 Ford Windstar

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

stormbrewin
  • 426 Answers

SOURCE: Rear license plate lights not working.

Have you checked to see if you have power to the bulbs?A cheap test probe/light will tell you wether its a power supply issue or wether the problem is at the lights.Usualy your problem is simply blown bulb/s.Have you replaced it/them to check?Good luck with it and if you need more let me know

Posted on Dec 28, 2008

michigan man
  • 3533 Answers

SOURCE: how to remove the rear light on my Freestar license plate

in most cases you have to open the rear tailgate remove the panel and then you have access to everything in the door

Posted on Jan 04, 2009

  • 12 Answers

SOURCE: Need to change license plate light on 2004 F150

Try turning the socket that holds the bulb to the left and pull it out to get to the bulb some times these get so hot that they start to melt so it might be hard to turn

Posted on Mar 13, 2009

c17hydro
  • 2984 Answers

SOURCE: how to change the license plate light on 2001 ford focus zx3

Take a thin blade screw driver and gently pry between the rubber seal and the metal and pop the light out, replaced the bulb and pop the light back in. works fine.

Posted on Mar 22, 2009

Danniboi
  • 1098 Answers

SOURCE: I tried changing the license plate bulb on my 2001

Sounds like something is connecting to the car body, I would inspect the bulb you changed make sure the metal clips or wires are not touching anything.

Posted on Jan 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MRear license plate light Or fuse on a 2001 Ford Ranger


The license plate lights get B+ power from headlamp switch . No seprate fuse for those lights , Bulb's good ? Headlamps , park lamps all work ?

Aug 21, 2016 | Ford Cars & Trucks

1 Answer

Plate light does not work, but lights are good and sockets seem good


check bulb the number plate light runs on the same circuit as the side lights so if they are working its got to be a bad earth on the plate light

Jan 24, 2016 | Cars & Trucks

1 Answer

My rear wiper, defroster and licence plate lights stopped working on my 2007 suzuki swift but when I open the rear hatch the licence plate lights come on . Any ideas what's wrong?bad ground?


[PDF]Wiring Diagram.pdf - Ken Gilbert

ken-gilbert.com/wrx/mans/99.../Wiring%20Diagram.pdf
Each connector number shown in the wiring dia- ... Rear defogger cord (Ground). Fuel tank cord,. Roof cord, ... circuit. Then check the switch, relay, fuse, ground, etc. 4. .....Rear wiper motor. Rear wiper ... License plate light RH. Tail light LH.

#? license plate light - Circuit Wiring Diagrams

circuitswiring.com/tag/license-plate-light/
2008 Volkswagen Newbeetle Main Fuse Box Diagram 2008 Volkswagen Newbeetle ...Parts: rear window defogger, shift lock, battery positive voltage, interior light, A/C clutch, ... brake light, daytime driving light, wiper and washer system, vacan, fuel pump, central ... 1997 Suzuki Geo Tracker Left Dash Fuse Box Diagram.

#? license plate light - Circuit Wiring Diagrams - Page 3

circuitswiring.com/tag/license-plate-light/page/3/
Audi A4 Engine Fuse Box Diagram Audi A4 Engine Fuse Box Map Fuse Panel ... mirror control, wiper, washer, horn, brake light, cruise control, heated rear window, ... 2003Suzuki Aerio Dash Fuse Box Diagram 2003 Suzuki Aerio Dash Fuse Box ... rear defroster, fuel injection controller, radio, A/T controller, hazard light, ...

Jan 05, 2016 | Suzuki Cars & Trucks

1 Answer

My license plate lights are not working. I have voltage at the trunk light (11.48 VDC), but not from the two license plate sockets when I turn the headlights on. I uncliped and removed the sockets in order...


could have poor ground wire use 12 volt test light check probe socket positive wire could be grey green wires and touch ground if test light works you have bad ground to license plate lights.and license plates lights have fuse control circuit.

Oct 22, 2013 | 2001 Jaguar S-Type

1 Answer

Replace license plate light


what country? ( export below means , NOT USA)
its in the FSM
quote:
A single standard equipment rear license plate lamp unit is integral to the
license plate mounting bracket just below the left rear lamp unit on vehicles manufactured for domestic
markets. A bracket with two rear license plate lamps is located on the rear bumper directly below the
spare tire on vehicles manufactured for export markets.
and HOW TO: quote
1. Disconnect and isolate the battery negative cable.
2. Remove the license plate from the rear license plate bracket.
3. Remove the four screws (4) that secure the rear license plate bracket and lamp unit (3) to the four spring
nuts (2) in the rear body sheet metal (5).
4. Pull the bracket and lamp unit away from the rear body sheet metal far enough to access and disconnect
the body wire harness connector (1) from the connector on the back of the bracket and lamp unit housing.
5. Remove the bracket and lamp unit from the vehicle.
unquote the FSM.
Buy one for $20-

Aug 19, 2013 | 2010 Jeep Wrangler

1 Answer

Tag light is not working. is there a fuse that will get the light turned back on?


The fuse labeled REAR PARK LP 15A in the right instrument panel fuse box powers the rear park lamps, and the tag lamps. If your rear park lamps are working then you most likely need to replace the tag lamps (bulbs). Use the following procedure to replace the lamps.

To Remove:
  1. Remove the two mounting screws from the license plate lamp.
  2. Remove the license plate lamp from the rear bumper fascia.
  3. Remove the license plate lamp socket by turning it counterclockwise.
To Install:
  1. Install the license plate lamp socket by turning it clockwise.
  2. Position the license plate lamp to the rear bumper fascia.
  3. Install the license plate lamp mounting screws.

Feb 17, 2011 | 2004 Chevrolet Impala

1 Answer

License plate light wires


Well if you can see that you have 2 black wires on No plate light and you can see the rear lights then get a test light and turn on the parking lights with test lighttest light to earth and the point stick into wires on rear light till it lights then run wire from there to No plate...1 wire will go to light and 1 to Earth put earth to earth screw and other to No plate lisht good

Sep 23, 2009 | 1996 Chevrolet Blazer

1 Answer

How do I change the rear license plate light bulbs?


License Plate Lights Removal & Installation License plate lamp retainer clips
a555c7b.gif
To Remove:
Remove or disconnect the following:
  1. License plate
  2. Pin-type retainers and the luggage compartment lid trim panel
  3. License plate lamp electrical connector
  4. Lamp socket from the license plate lamp
  5. Using a suitable tool, through the access hole, release the clips and remove the license plate lamp
To Install:
  1. Install or connect the following:
  2. License plate lamp
  3. Lamp socket to the license plate lamp
  4. Electrical connector
  5. Luggage compartment lid trim panel
  6. License plate

Jun 06, 2009 | 2000 Lincoln LS

2 Answers

License plate bulb on 1997 Cadillac deville


this is straight out of the book ok



  1. Open the rear compartment lid.
  2. Remove the rear compartment lid trim.
  3. Pull back on the rear compartment trim panel.
  4. Unplug the lamp connector from the rear compartment lid wiring harness.
  5. Press the grommet out of the rear compartment lid.
  6. Remove the nuts retaining the lamp assembly to the rear compartment lid.
  7. Remove the bulb.

Mar 07, 2009 | 1997 Cadillac DeVille

Not finding what you are looking for?
1999 Ford Windstar Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...