Question about 1999 Lincoln Navigator

Open Question

Where is 2000 lincoln navigator compressor relay located

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 740 Answers

SOURCE: 2000 lincoln Navigator air suspension

There are level control sensors they look like little arms (with joints like your elbows) mountesd on lower control arms. They may be at fault they control the height and turn the pump off when the height is reached. try adjust height first before you replace, they can be adjusted. Good Luck

Posted on Dec 17, 2008

  • 82 Answers

SOURCE: 99 lincoln town car air suspension compressor

the compressor is in the left front fender behind bumper cover, there is a retrofit kit to go to hard coils, only like 130 bucks..... best bet some one prob charge 50 bucks to install and prob solved easily

Posted on Jan 20, 2010

  • 1757 Answers

SOURCE: diagram 2000 lincoln navigator 5.4 firing order

My apologies for the delayed response.
I am going back to answer - unanswered questions. I have only been on this site for the past 4-months. Questions Posted have exploded (+55%) since joining.
I do not know if you still need this information, but I am answering it either way.


For the 5.4L:
Firing Order:
1-3-7-2-6-5-4-8
Cylinders:
(back of engine)
4-----------8
3-----------7
2-----------6
1-----------4
(front of engine)

Again my sincerest apologies....

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Posted on Mar 04, 2010

  • 3911 Answers

SOURCE: need to know the location

those airbag suspension systems are junk. you are going to spend more than the value of the car fixing it and then it will just go bad again in a few years.

take a look at this site, permanent fix for the whole system.

www.strutmasters.com

Posted on Sep 01, 2010

  • 62 Answers

SOURCE: 2003 lincoln navigator. The

I know you stated you checked all fuses and relay and they're ok but The 2003 Lincoln Navigator had two differently (wired) air ride systems. A early production and a late one, and I think I may have a good Idea of what your problem may be and will walk you through how to properly test the system. The early production navigators used a solid state compressor relay and the later production units used a standard style relay. The early ones with the solid state type has been known to have some problems and working for a Ford, Lincoln Dealer for 21 years I have replaced a good number of these solid state relay for a air ride compressor inoperative concern. There seems to be some confusion on the location of the solid state relay. I would advise you to look behind your front bumper on the passengers side of your vehicle (and below your headlight) and see if you have a 4 wire relay that's aluminum and finnd ribs on the front of it and I believe a black base where the wiring connector plugs in. (this will be mounted to the radiator support) if so, you Have got the early production style. I will walk you through how to test this relay and also help you to isolate the cause of your problem. I highly recommend using a volt ohm meter for these tests. I do not recommend using A TEST LIGHT due to the fact that you will be testing a circuit that is wired to the air ride control module, and there is a possibility of you damaging the module with a test light !!! I have been there, done that, NOT GOOD.
Ok with that said: your wire colors should be as follows:
one that's( gray and red)
another that's (light green and red)
another that's (dark blue and yellow)
and one that (light blue and pink).
Disconnect the connector at the relay and you'll be testing the wires in the connector (THAT HOOK UP TO THE RELAY). The air ride compressor and the air ride solid state relay share the same ground which is the light green and red wire.
Turn your volt ohm meter to dc volts scale and attach the black wire (NEGATIVE) lead of the volt ohm meter to the light green and red wire.
Hook the red lead of the volt ohm meter to the light blue and pink wire.
Here your volt meter should read battery voltage (of your car's battery) if not check the (F2-111) 50 amp designated fuse in the fuse box under the the dash on the passengers side (KICK PANEL).
If this fuse is ok, make sure you were making good contact with your test leads into the compressor relay connector.
If you're comfortable with the fact that you have a good connection at the relay connector and your fuse tested ok, then you have a ground problem at ground point G101 which is located right near the mounting location of the air ride relay.
If you had battery voltage when you tested between the (light green and red) and the light blue and pink wires, you have confirmed the power source and ground to the relay.
I should clarify myself at this point. The wires at the relay are as such: The ground is the light green and red wire, the light blue and pink is the fused power source to the relay, the dark blue and yellow wire is the relay trigger source from the air ride module to the air ride relay, and the grey and red is the relay output (battery +) to turn on the compressor. OK.
So now we're down to checking the trigger source to the relay and the relay output. At this point I want you to re-hook up the volt ohm meter with the meter still set at volts d/c scale and reconnect the (red lead) of the volt ohm meter to the (light blue and pink wire) and connect the (black) lead of the volt ohm meter to the dark blue and yellow wire (again at the relay connector).
Now this next step is best done with the help of an assistant!!
While watching your volt ohm meter, have your assistant turn on the key and open and close the drivers door two -to- three times. After cycling the door, you for a short time should see at least 5 volts minimum, if not battery voltage at your meter.
(this is a little bit unclear to me due to the fact the air ride module shows that the dark blue and yellow wire, as a ground from the air ride module to the relay. but does not clarify exactly what value that ground signal should be). I am referencing Fords own wiring diagram.
A solid state relay usally is allowed a trigger source of a lower voltage then a standard relay. If you find you have no voltage reading at your volt ohm on this test, you'll first want to check fuses F2-20 which is a 30 amp fuse and F2-27 which is a 5 amp fuse in the same fuse box as the F2-111 fuse you checked earlier.
The last test you need to make at the relay is checking the relay output to the compressor. This will be done by again using the volt ohm meter. This time you'll want to hook the black lead of the volt ohm meter to the light green and red wire at the reay connector and hook the red lead of the volt ohm meter to the grey and red wire at the relay connector. Again for this test, you'll need to have a assistant turn on the key, then recycle the drivers door again.
If the relay is working properly you should have battery voltage, aproximately 12 volts showing on your meter. If not and all other test procedures results were correct, you have a bad relay.
If you have 12 volts on this test we have confirmed the relay is good and the trigger signal from the air ride module is operating as designed.
If the pump runs like you said (when it is straight wired ) the remaining possiblity is a broke wire between the air ride relay to the air ride pump (this being the grey and red wire) which you can test by switching the volt ohm meter to the ohms scale and touching one lead of the meter to the grey and red wire at the relay connector and the other to the grey and red wire at the compressor (with the compressor and the relay both disconnected). Your reading here should be 0.5 ohms or less. If you have under 1.0 ohms you're ok but specs are 0. 5 or less.
If you have an auto ranging type ohm meter, be sure your reading in ohms and not kilo ohms or mega ohms.
If you find while performing the test from the air ride module to the air ride relay (dark blue and yellow wire) referenced as the trigger signal, incorrect and all fuses all checked o.k. then it is possible the air ride control module is defective. But, before condemning the module, there are a multitude of input signal;s to the module that would have to be checked.
WARNING: Make sure your tests are accurate. Good to check and re-check each test. Be confident of your results.
Inaccurate tests and inaccurate test results= unnecessary parts replacement. Results are large dollars spent when unneeded.
Hope this helps you out.thanks for using fixya

Posted on Jan 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHERE IS THE REAR HEIGHT SENSOR ON 2004 LINCOLN NAVIGATOR


Usually between the frame and the rear axles. A lever type device, should be fairly easy to locate. Check that the compressor is building air pressure and storage tank. Air bags not leaking and etc.

Feb 13, 2013 | 2004 Lincoln Navigator

1 Answer

Compressor powering up while car is off


Replace the AC compressor relay, it may be sticking on. Check the owners manual for location in the under hood fuse and relay center.

Jul 15, 2012 | 2004 Lincoln Navigator

1 Answer

2000 navigator: sit higher on one side than the other. replaced both air springs, front air struts, compressor, levelers, compressor relay. now the passenger side sits about two inchs higher than the...


make sure you don't have an air leak at the springs or the compressor. but you may want to have the air suspension module checked for fault codes. the module itself may be the issue not processing the inputs correctly and mis-leveling the vehicle.

Aug 03, 2011 | 2000 Lincoln Navigator

1 Answer

Wheres the air ride compressor relay located


The 2003 Navigator COMPRESSOR module is located under the dash on drivers side above the parking brake pedal.

Read more: http://wiki.answers.com/Q/Where_is_the_air_ride_suspension_relay_on_a_2003_lincoln_navigator_located#ixzz1AWFpFFoj

Jan 09, 2011 | 2003 Lincoln Navigator

1 Answer

Air suspension


In the Passenger Compartment Fuse Panel (below and to the left pf the steering sheel by the brake pedal), remove the panel cover t access the fuses and check the position 20, 5AMP for AIR SUSPENSION MODULE...

3edba24.jpg

This and other details canfind in the Navigator-Owner-s-Manual

Hope this help (remember comment and rated this).

Apr 29, 2010 | 2000 Lincoln Navigator

2 Answers

I have a 2000 lincoln navigator. I have had


have ur body control mogual checked ....... thay are known to do that ...has nothing to do with the main brain . it is located under the dash drivers side black box

Apr 26, 2010 | 2000 Lincoln Navigator

1 Answer

2000 Lincoln Navigator. Rear suspension is all the way down and compressor will not run. Thanks Scott


the place to start is the suspension shut off switch
located behind the right rear panel.
hope this helps if not gimme a shout and we will take it to next level good luck

Jan 13, 2010 | 2004 Lincoln Navigator

Not finding what you are looking for?
1999 Lincoln Navigator Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...