Question about 2003 Audi A4 Cabriolet
Need to find out how to disassemble the glove box door to expose the latch assembly
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Very easy - the car is designed to have these parts as being removable for the timing belt service. Opening the car is called the "service position" and involves taking these parts nearly off the car. Use the link below (it's a link to a DIY procedure for doing the timing belt on the car) - it'll show you what to do in order to remove the front clip of the car and remove the core support and radiator.
Posted on Feb 10, 2009
SOURCE: electrical fault Audi A4 2002
PRISE OUT THE TRIM PANEL AT THE BASE OF THE ARMREST WITH A FLAT-BLADED TOOL UNDO 2 SCREWS(DRIVERS DOOR) SINGLE SCREW ACCESSIBLE THOUGH THE ARMREST ON PASSENGER SIDE ,NOW GO TO THE BASE OF THE DOOR TRIM UNDO THE SCREW IN THE CENTRE,ONTO THE TOP TRIM NOW ABOVE THE RELEASE HANDLE,STARTING AT THE FRONT EDGE(DOOR HINGE SIDE) CAREFULLY PULL THE TRIM PANEL AWAY FROM THE DOOR TO RELEASE THE CLIPS,THEN SLIDE IT TO THE FRONT TO UNHOOK THE REAR EDGE OF THE TRIM PANEL,UNDO THE 4 SCREWS YOU CAN SEE,UNHOOK CABLE FROM REAR OF INTERIOR DOOR HANDLE,DISCONNECT WIRING PLUGS SPEAKER ,WINDOW MOTOR CONTROL UNIT AND THERE YOU HAVE IT ..EASY... IF YOU START NOW YOU WILL HAVE IT FINISHED IN 2 DAYS...ONLY JOKING....SHOULD TAKE 1 HOUR..HOPE THIS WILL BE OF SOME HELP TO YOU...LET ME KNOW HOW YOU GOT ON
Posted on Feb 10, 2009
FIRST CHECK THE CABLES THAT RUN INTO THE DOOR BECAUSE THEY CAN GET CUT THOUGH COMMON PROBLEM (JUST WERE THE DOOR HINGES INSIDE RUBBER BOOT.) DOOR PANEL REMOVAL...... PRIZE OUT THE TRIM PANEL AT THE BASE OF ARMREST UNDO TWO SCREWS (DRIVERS SIDE) OR ONE SCREW ACCESSIBLE THROUGH THE ARMREST UNDO THE SCREW AT THE BASE OF THE DOOR TRIM IN THE CENTRE. STARTING AT THE FRONT EDGE CAREFULLY PULL THE TRIM PANEL (ABOVE THE INTERIOR RELEASE HANDLE ) AWAY FROM THE DOOR TO RELEASE THE CLIPS, THEN SLIDE IT TO THE FRONT TO UNHOOK THE REAR EDGE OF THE TRIM PANEL.UNDO THE 4 SCREWS IN THE TRIM PANEL RECESS NOW PULL THE DOOR PANELAWAY FROM THE DOOR FRAME RELEASING THE RETAINING CLIPS, SOME FORCE WILL BE NEEDED PREPARE FOR SOME CLIPS TO BE BROKEN THEN LIFT THE DOOR PANEL UP SQUARELY NOW YOU CAN EASILY GAIN ACCESS TO ELECTRIC MOTOR.HOPE I WAS SOME HELP TO YOU THANKS STAN
Posted on Feb 23, 2009
SOURCE: Audi A4
Not sure if they've changed it but this is what i do for my 99 a4
First remove the screw in the handle pull, it should be next to where your fingers go.
Pull down on the black piece of plastic and remove the screw form the door
Then remove the screws on either end of the door, one near the door jam on top and one near the other side, same place.
Finally pull up then out and the door panel should come out
Hope that helps
Posted on Jun 17, 2009
Tips for a great answer:
Mar 05, 2017 | 2007 Volkswagen Beetle
Feb 01, 2015 | 2011 Nissan Murano
Dec 11, 2014 | 2006 Buick LaCrosse
Apr 03, 2014 | 2006 Honda Accord
Sep 15, 2011 | 2000 Chevrolet Blazer
Jan 07, 2011 | 1997 Cadillac Catera
Oct 16, 2009 | 1994 Volvo 850
Jun 07, 2009 | 2002 Volkswagen Jetta TDI
Sep 29, 2008 | 1998 Cadillac DeVille
Sep 14, 2008 | Subaru Outback Cars & Trucks
108 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: