Question about 1999 Buick Century

Open Question

Where is the oil pressure switch located on a 1999 Buick Century Custom with a 3.1 v.6 engine?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 1998 buick century custom

necesito diagrama electrico de las luces

Posted on Aug 11, 2008

Ad
  • 341 Answers

SOURCE: How to change a water pump on a 1999 Buick Century 3100?

the water pump on the 3.1 isnt to hard to change ...

  1. Disconnect the negative battery cable.
  2. Partially drain the cooling system into a suitable container.
  3. Remove the drive belt guard.
  4. Loosen the water pump pulley bolts before removing the drive belt. This should help keep the pulley from turning as the bolts are loosened.
  5. Remove the drive belt. Remove the water pump pulley bolts and remove the pulley.
  6. Remove the water pump bolts and separate the pump from the engine front cover.

Posted on Dec 09, 2008

  • 1779 Answers

SOURCE: how do I change the fuel filter in a 1999 Buick Century Custom?

Philly, the fuel filter is attached to the frame in front of the gas tank, under the driver side of the car. You must relieve the pressure in the fuel line before you start, and it is also recommended that you disconnect the neg. battery cable. After disconnecting the neg. cable, remove the gas cap. Next, look under the hood on the fuel rail for a shrader valve (like the type on a bicycle tire). Place a rag under the valve, remove the cap, and press the valve in with a plastic pen to relieve the pressure in the line. You can now go under the car to remove the filter. You can disconnect the fuel lines easily with an inexpensive plastic disk made for this purpose (only a few $ for several sizes at a parts store). Be careful of fuel in the line that will drain out, no smoking or sparks during this procedure. Should be 1 bolt securing filter to frame. Note arrow on new filter, and install in the correct direction. Replace cap on shrader valve, put gas cap back on, reconnect battery cable. The low coolant light is probably a faulty sensor signaling that it's low, when it's actually ok. Look for wires coming from the reservoir bottle, you should be able to find the sensor at the end of the wires to replace it. If you change the fuel filter in a garage, leave the door open for air circulation, gas fumes can explode easily, having the door open will help dissipate the fumes.

Posted on Apr 05, 2009

ZJLimited
  • 17970 Answers

SOURCE: where do I find a diagram of the fuse boxes in a

Visit gmownercenter_buick (1993-present. Must have a Yahoo ID to log in.) for acces to the Owners Manual.

Good luck (remember rated this help).

Posted on Mar 13, 2010

Testimonial: "Absolutely fantastic. Had searched the internet for days to find an answer to my question. Posted it on FixYa.com and got my answer in 30 minutes. "

ZJLimited
  • 17970 Answers

SOURCE: : where is the thermostat located on a 2002 buick

For 2002 Buick Century 3.1L SFI OHV 6cyl

zjlimited_444.jpg

Fig. The thermostat on this 3.1L is mounted horizontally and uses an offset housing/water outlet

  1. Disconnect the negative battery cable.
  2. Partially drain the cooling system into a suitable container, to a level below the thermostat.
  3. It is usually possible to leave the radiator hose attached and simply remove the thermostat housing (also called a water outlet) and flex the radiator hose enough to service the thermostat. It is good practice, however, to remove the radiator hose so the thermostat housing can be given a thorough cleaning. Debris on the thermostat housing sealing surface can cause leaks.
  4. Some applications may have electrical connections to sensors which mount in the thermostat housing. Use care when detaching these connectors.
  5. Unfasten the thermostat housing bolts and remove the housing.
  6. Remove the thermostat by simply pulling out. Discard the gasket.
To install:
  1. Clean all parts well. Make sure the sealing surfaces on both the thermostat housing gasket flange and the intake manifold are clean and free of corrosion damage. It is good practice to run a thread cutting tap or a clean bolt into the threaded holes in the manifold to clean out old sealer and dirt. The threads should be clean so the thermostat cover clamps the gasket evenly at assembly.
  2. Position the thermostat in the intake manifold. Make sure it is seated.
  3. Position a new gasket over the thermostat. If no gasket is used, apply a 0.125 in. (3mm) bead of RTV sealer to the thermostat housing and install the housing. Lightly lubricate the bolts with clean engine oil. Torque to 18-20 ft. lbs. (23-27 Nm).
  4. If removed, attach the radiator hose to the thermostat housing.
  5. Refill the engine with the proper mix of DEX-COOL®and water. Connect the negative battery cable, start the engine and check for leaks.

Good luck (remember to rate this answer).

Posted on Jan 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locating the knock sensor on a 1999 Buick LeSabre Custom


the knock sensors are threaded in to the block on either side of the engine. One is located near where the oil dipstick tube goes into the oil pan. The starter will need to be removed to see/replace. The other is in he same place on the opposite side of the engine.

Oct 06, 2016 | 1999 Buick LeSabre Custom

2 Answers

Will the oil sensor switch shut the engine down


Well, yes and no.
If the red oil pressure light comes on, yes the engine could stop running. You could actually lose oil pressure, or the switch could fail.
A "change oil" notice would not cause the engine to stop.

Jan 05, 2016 | 2004 Buick Century

1 Answer

Where is the oil sending unit on a 1995 Buick Skylark 3.1 V6?


OIL PRESSURE SWITCH

1995 Buick Skylark 2.3L MFI DOHC Quad 4 4cyl

The Oil Pressure Switch is located:

OIL PRESSURE SWITCH

1995 Buick Skylark 3.1L SFI OHV 6cyl

The Oil Pressure Switch is located: Under hood, center, front engine area, front driver side of engine, mounted in engine block

Jan 05, 2013 | 1995 Buick Skylark

2 Answers

I have a 1995 buick century custom and all of a sudden all the oil leaked out of the engine with no warning signs


You might have crushed the oil crank and poured all the oil. Have you looked at the oil seals as well on the engine? It should not have spilled oil all over it. If so, then attend to them, but check out the first one at the bottom of the engine.

Dec 02, 2010 | Buick Century Cars & Trucks

2 Answers

Valves ticking in my 1999 buick century


Did you check your oil level? Is the oil light on? (No oil pressure) try changing oil & install an engine additive for noisey lifters, If none of this works need to place lifters

Sep 12, 2009 | 1999 Buick Century

1 Answer

My car is jerking while accelerating and reaching certain RPM


clean mass air flow sensor check for mil light

Jun 01, 2009 | 2002 Buick Century

2 Answers

Radiator Plug Location


It should be on the right lower side of the radiator when looking at the engine .

Jan 08, 2009 | 2001 Buick Century

3 Answers

98 buick centry 3.1 6 cyc one owner family owned


Unfortunately, you've got serious problems. The GM 3.1 and 3.4 engines have a nasty habit of breaking camshafts. For some reason, which I have yet to determine, the cam bearings seize on the cam and the camshaft ends up breaking in half. The engine will continue to run, albeit very poorly since all the cylinders are not working because the rear half of the camshaft, which runs the oil pump, is not spinning.

Aug 29, 2008 | 1999 Buick Century

Not finding what you are looking for?
1999 Buick Century Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6910 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...