Question about 2001 Mazda 626

1 Answer

How 1996 mazda 626 front axle shield broken - 2001 Mazda 626

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Mazda Master
  • 2,432 Answers

The drive shaft has to be removed to replace the rubber boot .you will have to dismantle the CV joint , clean and repack the joint with special grease and fit a new boot.

Posted on Jun 16, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 196 Answers

SOURCE: sounds like the axle popping

well turn the wheel to the right or left and look at the boots on the cv shafts if the are torn open the shaft will need to be replaced.

Posted on Jan 08, 2009

motor1258
  • 6674 Answers

SOURCE: cost to replace waterpump on mazda 626 1996

Go to (repairpal.com) and enter all your info & pick repairs for pricing in your area.

Posted on May 03, 2009

  • 30 Answers

SOURCE: transmission in 1996 mazda 626 slow to shift high rpm

if its reving high then shifting then your trannys going

Posted on Jun 27, 2009

  • 1348 Answers

SOURCE: How to remove drive axles

the lower ball joint has to be undone.cotter pin and castle nut
the axle nut 36mm has to be undone.
.the control arm swung away from the end of the axle shaft.
using a pry bar,pry the knuckle away from the transmission,as just pulling out will not release it.
installation is done by lining up the shaft in the transmission and using wood or a brass drift to hit the shaft to seat it in place.
the lower conrol arm is a little tricky to move so that the hub fits over the axle .on average about 50 lbs force is needed to move it out of the way.
be sure to replace the cotter pin with the head fully inserted into the castle nut slot.
cheers and good luck.if you run into problems,get a haynes manual,it clearly explains and has pictures,and then you have a service book for your car.

Posted on Jul 12, 2009

  • 288 Answers

SOURCE: how long does it take to replace a timing belt on

about 5.5 hours

Posted on Jan 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can the full front axle be exchanged from a 02 mazda 626 to a 97 mazda 626?


You install a complete reman front drive axle

If you like, you can buy a new one,for more money

The CV Joints (2) are part of the axle assy,you
will see that in the pictures your ordering from

You order parts that are application specific

No need to worry what fits another vehicle

Have to get the correct side,they are different lengths
& part numbers

Sep 30, 2014 | 1997 Mazda 626

1 Answer

Popping rattling noise in front slipping and leaking tranny


Rebuild the transaxle & check the CV Axle Joints for problems,
as well as replace all motor & trans mounts

May 10, 2014 | 1996 Mazda 626

1 Answer

Popping sound from left front when taking off but sound disaprears at about 25 to 30 mph cv axle is good


it could be the bearing it should have been replaced when the cv joint was

Dec 19, 2010 | 1996 Mazda 626

1 Answer

1996 mazda 626 se V6 2.5 firing order south african model with a mitsubishi distributor


looking from the front of the engine back towards the gearbox,left bank 135..right bank 246...Firing order 135624.

Oct 01, 2010 | 1996 Mazda 626

1 Answer

Spark plug wire diagram position from distributor to engine on mazda 626 4 cylendar


For the 1996 Mazda 626 2.0L DOHC In-Line 4-Cylinder:

Firing Order:

1 - 3 - 4 - 2

Cylinders:
.........(back).........
|..1....2....3....4...|
........(front)

Distributor:
__________
/////////////////| <---2
_______________
//////////////////////////| <------1
___________
///////////////////| <----C
_______________
//////////////////////////| <-------3
__________
/////////////////| <----4

Let me know if this helped and thanks for using Fixya!

Aug 18, 2010 | 1996 Mazda 626

1 Answer

Mazda 626 popping noise in front driver side when turning and or body shifting


Your Constant velocity joints have gone bad. the Boot that holds th grease has leaked out all the grease and the bearing inside are not being lubicated and thats where the poping comes from. Have someone look at the axle (CV) to determine if repairable or you might have to replace the axle. Hope this helps

Jun 27, 2009 | 2000 Mazda 626

1 Answer

Transmission in 1996 mazda 626 slow to shift high rpm


if its reving high then shifting then your trannys going

Jun 27, 2009 | 1996 Mazda 626

1 Answer

Mazda 626


First put a jackstand under the car have it jacked up fairly high where you can get under it easily then take a really strong regular screw driver or a small pry bar slide up between tranny and the axle piece you are trying to get out and tap with your hand or a rubber mallet the bottom of the pry bar or the handle of the screw driver towards the opposite side of the car of what you are working on.

May 18, 2009 | 2000 Mazda 626

1 Answer

Engine parts Cylinder head


Check the casting number on the two heads and see if they are the same. If not, your best bet is to call a machine shop and give them the casting numbers and see if they are interchangable...

I hope this helps

Aug 21, 2008 | 1996 Mazda 626

Not finding what you are looking for?
2001 Mazda 626 Logo

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...