Question about 2003 Mazda Protege

1 Answer

Front axle popped out and broken now tranny slipping?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 38 Answers

Tranny fluid is low,,,top it up and check fore leaks.,you may need a new axle seal on the tranny

Posted on May 10, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What do you have to take off to get the alxe out of a 1998 olds 88


Tire, Caliper and bracket, tie rod to spindle, lower strut bolts, remove brake caliper hose from bracket on strut, remove axle nut, Pull spindle away from strut, push axle out of hub, use pry bar and pop axle from Tranny. Make sure when you reinstall axle into tranny your careful not to rip tranny axle seal.Make sure it is fully seated also.

Nov 07, 2014 | Cars & Trucks

1 Answer

Popping rattling noise in front slipping and leaking tranny


Rebuild the transaxle & check the CV Axle Joints for problems,
as well as replace all motor & trans mounts

May 10, 2014 | 1996 Mazda 626

3 Answers

My front driver side axle popped out. Can i drive it?


Yes, you can replace the front axle on a Mercury Grand Marquis. All cars have two axles whether they are front wheel or rear wheel drive.------------------------------------------------------------------------------------
Tacho Pro 2008

Feb 22, 2013 | 2004 Nissan Titan

1 Answer

Can't get axle to pop out of transmission. Any suggestions?


the way i found thats best. is use a crow bar between axle and tranny or similar, to remove it. on end of axle is only a slip ring to hold it in. when putting back on just push axle into tranny until you hear it lock in place. or it is in there firmly. have a good one !

Jan 30, 2011 | Plymouth Voyager Cars & Trucks

3 Answers

I need to remove my front axel on my 1989 toyota camry


Jack up car and apply e-brake. car will roll if one of the front tires leaves the ground. remove tire , spindal nut and lower ball joint bolts. remove axle from hub then use a prybar to pop it out of trans. the passenger side will have a braket holding axle to engine , remove bolts from braket or squeeze snap-ring to rmove axle from braket.

Jan 11, 2011 | 1989 Toyota Camry

1 Answer

I have a 1998 Pontiac Sunfire coupe. The car runs amazing has alot of get up and go but the transmission seems to slip alot while making turns, or at complete stops. it does leak fluid alot. I'm curious as...


it sound to me that the tranny needs to be resealed that the seals and gaskets are worn. There are many places the tranny fluid can come out of like where the front axles go into the tranny or the front seal or the pan gasket

Sep 02, 2010 | 1998 Pontiac Sunfire

1 Answer

Changing cv axle on passenger side


axle nut, bottom ball joint. pop the axle out of the hub and let it hang. pry bar between the inner joint of the axle and tranny. a quick pry should pop it out

Apr 11, 2010 | 2001 Dodge Neon

1 Answer

I just want to know what holds the axle to the flange on this car to figure out wethere i can replace my self as long as its only a few bolt i shouldnt have a problem


1-remove wheel2-remove axle center bolt.3-undo bolt of sway bar link on lower control arm.4-undo bolt of lower ball joint and separate lower control arm from steering knuckle,move knuckle aside while slipping cv axle out of knuckle.5-use pry bar to pop inner cv out of tranny.

Apr 17, 2009 | Hyundai Motor 1999 Elantra

Not finding what you are looking for?
2003 Mazda Protege Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...