Question about 1998 Toyota Sienna

Open Question

How to remove transmission on 1998 toyota sienna

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 12 Answers

SOURCE: change ignition lock cylinder

put the lock cylinder in the acc position and with a small screwdriver depress the pin retaining the cylinder then pull it sttraight out

Posted on Dec 24, 2008

Ad
  • 1861 Answers

SOURCE: toyota 1998 sienna foot break light indicator on

The brake fluid level in your master cuylinder reservoir is low.

Posted on Jan 17, 2009

  • 1 Answer

SOURCE: The sliding door handles of my 1998 Toyota Sienna have both broken.

I replaced both of my sliding door handles this weekend. It was actually pretty easy. Cheapest I could find the handles was a little over $70 each. The interior panel is held on with one screw and 10 nylon clips. The one screw is in the cup holder. Put you hand in the cup holder and push out at the bottom. It pops right off exposing the one screw. I started on the clips from the top at a corner. Seemed to be the easiest place to slide a screw driver under. Once I got the screw driver in, I started working my fingers under the panel. The clips run mostly along the top and bottom about 6 inches from the edge. I made an effort to apply the force as close to the clips as I could to reduce flexing the panel. Once I got the first clip to pop out the other followed pretty easy and the panel lifted right off. Carefully peel back the plastic barrier. The exterior handle is held on with two 10mm bolts. Connecting the short cable was pretty obvious once you could see everything. Now I have to teach everyone to open the side doors very gently! Hope this helps.

Posted on Mar 09, 2009

  • 8 Answers

SOURCE: My 1998 Toyota sienna will not start

The battery may be dying and does nothave the juice to turn the crank.

Posted on Aug 31, 2009

wireguy212
  • 1627 Answers

SOURCE: HOW MANY BELTS ARE THERE ON 1998 TOYOTA SIENNA. I

Three

Posted on Nov 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The rear bumper cover came off how can I reinstall it


2000 Toyota Sienna rear Bumper cover replacement (1998 ...

? 3:40
https://www.youtube.com/watch?v=AY1BBdg3q74
Sep 20, 2013 - Uploaded by SergSpace
2000 Toyota Sienna rear Bumper cover replacement (1998-2003) .... Automotive Bumper Repair Specialist- How to repairyour plastic bumper cover ... Toyota Sienna Rear Shock Installation 2003, 2004, 2005, 2006 - Duration: ... 2015 Toyota Sienna XLE - Duration: 28:13. by MikesCarInfo 35,234 views.

Fixing My Mom's Prius: Loose Rear Bumper Cover - YouTube




Nov 29, 2015 | 2005 Toyota Sienna LE

1 Answer

Location of 1998 toyota sienna shift soleniod A


Should be mounted on a bracket located on the very top of the transmission

Feb 18, 2015 | 1998 Toyota Sienna

1 Answer

What to do for sienna to reverse


It may be that you are low on the transmission fuied if it still doesn't work it may be your the filter in the transmission.

Jan 24, 2015 | 1998 Toyota Sienna

1 Answer

Where can I find a cheap shift solenoid for a 1998 Toyota Sienna


google it by punching in 1998 toyota sienna shift solenoid

Jun 25, 2014 | 1998 Toyota Sienna

1 Answer

How do you remove the frt turn signal assembly on a 1998 sienna


Here's a great video that will show you exactly how to remove the turn signal from your Toyota Sienna.

">

Dec 05, 2010 | 1998 Toyota Sienna

1 Answer

I changed transmision fluid of toyota sienna 1998,after ten days reverse gear not working only forward gears working,what is cause,no check light on dash board.


Changing the fluid will never harm your trans unless you do not fill it back up.

Reverse is all hydrolic. There is no electrical that could cause it. If you have park and forward, you don't have a lincage problem.

As much as I feel for you, (I satarted rebuilding transmissions in the 80's) you will have to get it rebuilt.

Sorry

Sep 03, 2009 | 1998 Toyota Sienna

1 Answer

My 1998 Toyota sienna will not start


The battery may be dying and does nothave the juice to turn the crank.

Aug 13, 2009 | 1998 Toyota Sienna

1 Answer

98 Toyota Sienna will "bog down" and get sluggish during acceleration. Idles fine and usually runs well when cold. Not fuel system or transmission-already checked by mechanics. Could it be the 02 sensor?


If you had an Oxygen Sensor issue, you would have the check engine light on at your dash. Have your guy hook up a scan tool to the car, and see if there are any codes stored.

Jul 17, 2009 | 1998 Toyota Sienna

1 Answer

Change ignition lock cylinder


put the lock cylinder in the acc position and with a small screwdriver depress the pin retaining the cylinder then pull it sttraight out

Dec 06, 2008 | 1998 Toyota Sienna

Not finding what you are looking for?
1998 Toyota Sienna Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...