Question about 2005 Mazda B2300 Regular

Open Question

23 timing marks

97 mazda truck 2.3 what timing specs for a timing light say when testing

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 58 Answers

SOURCE: what is the marks for timing a 3.0

a52cd8f.jpgthis is the left cam


6f1e269.jpgthis is the right cam


b9da80d.jpgthis is the crank.

on your tensioner you will have to remove the spring tensioner 2 bolts and put it in a vise thigten it down until you pin hole on it lines up with the pin hole on the tensioner and put a small drill bit etc in the whole to hold it compressed and reinstall it then put your belt on. hope this helps

if you are confused you can go to autozone.com and create an account with them and its free enter your car in it. and you can view the repair manual for free online and will tell you step by step with pics etc.

Posted on Mar 12, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set the ignition timing on mazda b2600 1994.




  • ADJUSTMENTS







  1. Check engine condition (spark plugs, leaks in hoses, etc.).


  2. Turn all electrical loads OFF.


  3. Warm up engine and run for three minutes at 2500 - 3000 rpm.




Test Connector For Tachometer
Test Connector


  1. Connect tachometer and timing light to engine (white check connector).


  2. Ground test connector (green: 1-pin) with a jumper wire.


  3. Check that idle speed is within specification.

M/T: 750 ±20 rpm in neutral

A/T: 770 ±20 rpm in park

Timing Mark







  1. Check that timing mark (YELLOW) on crankshaft pulley and the mark on timing belt cover are aligned.



5°±1°BTDC



  1. If timing is not within specification, loosen lock bolt and rotate distributor housing to adjust.


  2. Tighten lock bolt to 14 - 19 ftlb (19 - 25 Nm).


  3. After adjustment, disconnect jumper wire from test connector.

Mar 25, 2015 | Mazda Cars & Trucks

1 Answer

Mazda protige 1997 overheating


Some restrictive pulley tension usually is what causes a good belt to wear prematurely. Sounds like the water pump may be the culprit all along...(one of 2 belts) Be sure to have the alternator itself tested (free) at most parts stores...could be a combination of concerns. Hope this helps.

Jul 11, 2012 | 1997 Mazda Protege

1 Answer

Im replacing the timing chaine and I need to know what the timing specs are.


You don't need to know timing specs unless your installing a high performance cam and you have an adjustable timing chain set. You didn't spec the moter and there's more than one that comes in your car 3.9, 4.0,4.7, 5.2, 5.9. Tell what motor your working on and what kind of timing componants your trying to install. and I'll help you more. Stock or replacement stock you just line upp the marks. tell the engine I'll tell you where the marks are. If in doubt the intake valve opens between10 and 3 degrees before top dead center about on any engine some racing engines open the intake as much as 23 degrees before TDC but they don't idel smooth and their drivers don't care either.

Oct 01, 2010 | 2006 Jeep Grand Cherokee

1 Answer

What is the timing specs for a 97 toyota celica 2.2 engine


Cylinder #1 at top dead center. Mark on the camshaft gear is straight up,as referenced to engine. Note that the engine tilts to the rear so reference the flat line of the head for 12'oclock positioning of cam timing mark.Distributor rotor points to #1 cylinder. If you have crankshaft pulley off, and can see the timing mark there, it should be straight down with #1 at TDC. After reassembly, start engine and jumper E1 and TE1 in the diagnostics box. This gives a smooth steady idle. Use timing light pointed at crankshaft pulley and hooked to #1 cylinder spark plug wire to check. Loosen distributor's 2 mounting bolts enough to turn it. Adjust as necessary. If you are having trouble seeing the notch on the crank pulley, get a white paint pen to increase it's visibility. Reference the rotating pulley mark to the stationary mark on the lower timing belt cover.

Mar 28, 2010 | 1997 Toyota Celica

1 Answer

How to set timing on 97 ford probe gt


This is the specs...not too sure on what else you are asking about:

d23bf61.gif
Save to desktop and then zoom.

Jun 23, 2009 | 1997 Ford Probe

1 Answer

Timing settings


you should have timing marks that are lined up on your engine. You have your crank to line up at a certain point as well as the two cams. I don't know off the top of my head where these might be for this car but you can find it in a Haynes or Chilton manual if you so desire to also learn more about your overall car and take care of this or i can find these specs and send them your way. Up to you?

Feb 28, 2009 | 1992 Mazda 323

1 Answer

How to do ignition timing ford 2.8 mk2 granada


remove and plug vacume line on the distributer and find timing specs on the motor in the vehicle using timing light hook transducer cable to no# 1 cylinder set the idle to manufacturers specs make shure motor is warmed up to operating temp now point thr timing light at the timing plate on crankshaft pulley start the engine and watch for the mark on the harmonic pulley see where it is at when running now if the mark is not lining up with sugested degrees from manufacturer then u must loosen bolt on distributer only loosen 1/4 turn now rotate distributer clockwise or counterclockwise this will make the mark on the harmonic ballancer allign with manufactures required timing specs after aligning marks tighten distributer and unplug distributer vacume line and plug it back into distributer. and test if u need anymore specifics plz read manual carefully good luck

Jun 30, 2008 | 1978 Ford Granada

Not finding what you are looking for?
2005 Mazda B2300 Regular Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...