Question about 2007 Toyota Avalon

1 Answer

Connector location of driver side junction block behind center instrument panel

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 20,706 Answers

Not sure what is being asked here,
where is junction box.
or how it is wired?
FSM book or alldata.com has this.
may I ask what dont work? so we can know what boxes , apply?
the FSM is not layed out by geology but function, so i flounder.
there are many

INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (MULTIPLEX NETWORK BODY ECU) (POWER SOURCE)


connector location of driver side junction block b - 3e6de788-ba86-42e8-8f6a-e526505d100f.jpg

Posted on Jun 25, 2014

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 7353 Answers

SOURCE: where exactly is fuse box

its going to be easy to access.near the drivers left knee.

Posted on Sep 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse for Windows 1998 Pontiac Bonneville


RH Maxi fuse Block , 30amp circuit breaker PWR WDO/SR. There is also a relay -Power window / sunroof , instrument panel junction block ,position H .
IP Junction Block
Under the right side of the instrument panel, near the rear of the instrument panel compartment
IP Fuse Block
Under the left side of the IP, on the left IP sound insulator
RH MaxiFuse® Block
In the center rear of the engine compartment, near the cowl
I would check the relay ! circuit breakers don't go bad !
I wo

Jan 19, 2016 | Pontiac Cars & Trucks

1 Answer

1999 explorer smart junction box location


1999 explorer has Fuse Junction Panel
Left side of vehicle, below instrument panel not SJB . This vehicle also has a ( GEM ) generic electronic module.
Generic Electronic Module (GEM) C280
Behind center of I/P C281
Behind center of I/P C282
Behind center of I/P C283
Behind center of I/P Hope this helps ! what type of a problem are you having ?

Jan 25, 2015 | 1999 Ford Explorer

1 Answer

Junction box


match colour codes On plugs and cables

May 10, 2014 | 2007 Toyota Avalon

1 Answer

Driver side junction box


I suggest you purchase a factory wiring manual for the car. It will have all kinds of info like this for you to refer to. Ebay is a good place to find cheap manuals.

May 10, 2014 | 2007 Toyota Avalon

1 Answer

How many fuse box does a 2004 nissan infinity QX56 has


There is an Intelligent Power Distribution Module (IPDM), a Fuse & Relay Box, a Fusible Link Box, and a Fuse & Fusible Link Box, all of which are located at the right side of the engine compartment.
Then there is the Instrument Panel Junction Block, which is located behind the driver's side kick panel.

Feb 11, 2012 | 2004 Infiniti QX56

1 Answer

Hi I,ve got a 2000 Jeep Grand Cherokee, the problem I,m having is when I turn on the heating fan i get a mist or steam coming out of the vents smells like coolant could this be a heater core problem ,...


Yes, your core is leaking. The core is in the box under the dash. The procedure is quite involved. I will attempt to paste from autozone.com below:
  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Disconnect and remove the negative battery.
    CAUTION After disconnecting the negative battery cable, wait 2 minutes for the driver-s/passenger-s air bag system capacitor to discharge before attempting to do any work around the steering column or instrument.
  3. Drain the cooling system into a clean container for reuse.
  4. Remove the instrument panel by performing the following procedure:
    1. Turn the steering wheel in the straight-ahead position.
    2. Remove the A-pillar trim from both sides of the vehicle.
    3. Remove the top cover from the instrument panel.
    4. Near the windshield line, remove the 4 instrument panel-to-chassis nuts.
    5. Remove the scuff plates from both front door sills.
    6. Remove the trim panels from both sides of the inner cowl.
    7. Remove the floor console.
    8. Remove the fuse cover from the junction box.
    9. Remove the instrument panel cluster bezel.
    10. Remove the steering column opening cover from the instrument panel.
    11. Remove the steering column bracket from the instrument panel column support bracket.
    12. Remove the lower steering column shroud cover-to-multifunction switch screw; then, unsnap both halves of the shroud cover from the steering column.
    13. Disconnect the instrument panel wiring harness connectors from the following steering column components:
      Both lower clock spring connector receptacles Left multifunction switch receptacle Right multifunction switch receptacle Both ignition switch receptacles Shifter interlock solenoid receptacle Sentry Key Immobilizer Module (SKIM) receptacle, if equipped
    14. Turn the ignition switch to ON position; then, release and remove the shifter interlock cable connector from the ignition lock housing receptacle.
    15. Turn the ignition switch to OFF position; this will prevent the steering wheel from turning and the loss of the clock spring centering following steering column removal.
    16. Remove the 4 steering column-to-instrument panel steering column bracket nuts.
    17. Remove the steering column from the instrument panel.
    18. Disconnect both side body wiring harness bulkhead connectors, the Ignition Off Draw (IOD) wiring harness connector and the fused wiring harness connector from the junction block connector receptacles.
    19. Disconnect the instrument panel wiring harness-to-floor console component connectors:
      Air bag control module connector receptacle Parking brake switch terminal Transmission shifter connector receptacle
    20. Remove the 2 instrument panel wiring harness-to-floor console ground terminals located behind the air bag control module.
    21. Disconnect the instrument panel wiring harness-to-floor console retainers.
    22. Remove the instrument panel-to-floor console bracket screws and the bracket.
    23. Remove the driver-s side floor duct-to-heater/air conditioning housing assembly screw and remove the duct.
    24. If equipped with a manual heating-air conditioning system, disconnect the vacuum harness connector from behind the driver-s side floor duct.
    25. Remove the instrument panel steering column support bracket-to-driver-s side of the heater/air conditioning housing assembly screw
    26. Remove the instrument panel steering column support bracket-to-intermediate bracket screw.
    27. Remove the instrument panel steering column support bracket-to-driver-s side cowl plenum panel nut.
    28. Remove the 2 instrument panel-to-driver-s side cowl side inner panel screws.
    29. Remove the instrument panel end cap.
    30. Remove the lower right center bezel from the instrument panel.
    31. At the passenger-s side cowl side inner panel, disconnect the instrument panel wiring harness bulkhead connector from the lower cavity of the inline connector.
    32. Near the right side cowl inner panel, located under the end of the instrument panel, disconnect both halves of the radio antenna coaxial cable connector.
    33. Disconnect the 2 instrument panel-to-heater/air conditioning assembly wiring harness connectors.
    34. At the passenger-s side, remove the 2 instrument panel structural duct-to-heater/air conditioning housing assembly screws.
    35. At the passenger-s side cowl side inner panel, remove the 2 instrument panel-to-passenger-s side cowl side inner panel screws.
    36. With the help of an assistant, lift the instrument panel from the vehicle.
  5. Discharge and recover the air conditioning system refrigerant.
  6. Disconnect the air conditioning system lines at the evaporator. Plug the openings to prevent contamination.
  7. Disconnect the heater hoses from the heater core. Plug the openings to prevent coolant loss.
  8. If equipped with a manual temperature control system, unplug the heater/air conditioning system vacuum supply line connector from the T-fitting located near the heater core tubes.
  9. From the passenger-s side inner fender shield, remove the coolant reservoir/overflow bottle.
  10. From the passenger-s side in the engine compartment dash panel, remove the PCM; DO NOT unplug it, just move it aside.
  11. In the engine compartment, remove the heater/air conditioning housing-to-chassis nuts.
  12. At the center of the dashboard, remove the rear floor ducts from the floor heat duct outlets.
  13. Disconnect the heater/air conditioning housing wire harness connectors.
  14. In the passenger compartment, remove the heater/air conditioning housing-to-chassis nuts.
  15. Place covers inside the vehicle to catch any spilt coolant.
  16. Remove the heater/air conditioning housing assembly from the vehicle.
  17. Remove the foam gasket from around the heater core tubes.
    NOTE Note the position of the irregular shaped gasket so that it may be reinstalled in its correct position.
  18. Remove the heater core retainers and screws.
  19. If necessary, remove the mode door actuator for clearance to remove the core.
  20. Remove the heater core from the heater/air conditioning housing assembly.

    0996b43f8022fa8a.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of the instrument panel assembly-Grand Cherokee

Sep 16, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Where is the fuel pump relay located in a 1999 saturn sc1?


Hello! The fuel pump relay is located on the bottom right of the instrument panel junction block...the junction block is beneath the center of the instrument panel...

Guru.............Saailer

Jul 02, 2010 | 1997 Saturn SC

1 Answer

Replacing heater core on 2000 durango


  1. Disconnect the negative battery cable.CAUTION
    After disconnecting the negative battery cable, wait 2 minutes for the driver's/passenger's air bag system capacitor to discharge before attempting to do any work around the steering column or instrument

  2. Remove the instrument panel by performing the following procedure:
    1. Remove the trim from the right and left door sills.
    2. Remove the trim from the right and left cowl side inner panels.
    3. Remove the steering column opening cover from the instrument panel.
    4. Remove the 2 hood latch release handle-to-instrument panel lower reinforcement screws and lower the release handle to the floor.
    5. Disconnect the driver's side air bag module wire harness connector.
    6. If equipped, disconnect the overdrive lockout switch harness connector.
    7. Do not disassemble the steering column but remove the assembly from the vehicle.
    8. From under the driver's side of the instrument panel, disconnect or remove the following items:
      • The screw from the center of the headlight/dash-to-instrument panel bulkhead wire harness connector and disconnect the connector.
      • The 2 body wire harness connectors from the 2 instrument panel wire harness connector that secure the outboard side of the instrument panel bulkhead connector.
      • The 3 wire harness connectors from the 3 junction block connector receptacles located closest to the dash panel; 1 from the body wire harness and 2 from the headlight/dash wire harness.
      • The plastic park brake release linkage rod-to-rear parking brake release handle lever. Disengage the linkage rod from the handle lever.
      • The stoplight switch connector.
      • The vacuum harness connector from the left side of the heater/air conditioning housing assembly.
    9. Remove the instrument panel center support bracket.
    10. Remove the instrument panel wire harness ground screw located on the left side of the air bag control module (ACM) mount on the floor panel transmission tunnel.

Nov 08, 2009 | 2000 Dodge Durango

1 Answer

How to Replace a Heater Core


Removal & Installation

  1. Disconnect the negative battery cable.
    CAUTION After disconnecting the negative battery cable, wait 2 minutes for the driver-s/passenger-s air bag system capacitor to discharge before attempting to do any work around the steering column or instrument
  2. On diesel models, remove the passenger side battery and battery tray.
  3. Remove the instrument panel by performing the following procedures:
    1. Remove the air bag control module (ACM) and bracket from the floor panel tunnel.
    2. Remove the trim from both cowl side inner panels.
    3. Remove the steering column-to-instrument panel opening cover.
    4. Remove the 2 hood latch release handle-to-instrument panel lower reinforcement screws and lower the handle to the floor.
    5. Disconnect the driver-s side air bag module wiring harness connector from the lower instrument panel reinforcement.
    6. Place the wheels in the straight-ahead position and lock the steering wheel. Remove the steering column without disassembling it.
    7. From under the driver-s side of the instrument, disconnect or remove the following items:

      Parking brake release handle linkage rod from the parking brake mechanism located on the left cowl side inner panel. Instrument panel wiring harness connector from the parking brake switch located on the parking brake mechanism. Three wiring harness connectors (body wiring harness, headlight, dash) from the 3 junction block connector receptacles located closest to the dash panel. Head light/dash-to-instrument panel bulkhead wiring harness connector screw and disconnect the connector. Instrument panel-to-door wiring harness connector located directly below the bulkhead wiring harness connector. Infinity sound system wiring harness connector (if equipped), located at the outboard side of the instrument panel bulkhead connector. Stop light switch electrical connector. Vacuum harness connector located near the left side of the heater/air conditioning housing.
    8. Under the passenger-s side of the instrument panel, disconnect the radio antenna coaxial cable connector.
    9. Loosen both sides of the instrument panel cowl side roll-down bracket screws about 1 / 2 inch (13mm).
    10. Remove the 5 upper instrument panel-to-upper dash panel screws; remove the center screw last.
    11. Roll down the instrument panel and install a temporary hook in the center hole on top of the panel. Attach the other end to the center hole in the top of the dash panel. The opening should be approximately 18 inches (46cm).
    12. Disconnect the instrument panel-to-heater/air conditioning housing assembly wiring harness connectors.
    13. Using an assistant, remove the instrument panel from the vehicle.

  4. If equipped with air conditioning, perform the following procedure:
    1. Discharge and recover the air conditioning system refrigerant.
    2. Disconnect the refrigerant lines from the evaporator. Plug the openings to prevent contamination.
    3. Disconnect the refrigerant lines from the accumulator. Plug the openings to prevent contamination.
    4. Remove the accumulator.

  5. Drain the cooling system into a clean container for reuse.
  6. Disconnect the heater hoses from the heater core tubes.
  7. Remove the PCM from the dash panel and move it aside. Do not disconnect the PCM harness connector.
  8. In the engine compartment, remove the heater/air conditioning housing assembly-to-chassis nuts.
  9. In the passenger-s compartment, remove the heater/air conditioning housing-to-dash panel nuts.
  10. Pull the heater/air conditioning housing assembly rearward far enough to clear the studs and air conditioning drain tube holes.
  11. Remove the heater/air conditioning housing assembly from the vehicle.
  12. Remove the upper-to-lower heater/air conditioning housing screws and remove the upper housing.
  13. Remove the heater core from the lower housing.


    Fig. View of the heater/air conditioning housing assembly


    0900c15280225dc3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. View of the heater core

Apr 07, 2009 | 1997 Dodge Ram

Not finding what you are looking for?
2007 Toyota Avalon Logo

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...