Question about 1984 Chevrolet Corvette

1 Answer

How do i disconnect air-bag (passenger side )

Have to transport granddaughter to gymnastics no other car

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 124 Answers

Back seat? If no backseat there should be a switch on the dash, sometimes a key hole to disable it. (On/Off) If you want to permanently disconnect it you have to remove the dash and look for a yellow wire, only airbags have yellow wiring and remove the plug for that side. This will also cause the SRS light to come on and stay on until you take it to a certified airbag repairman. Meaning no airbags will work.

Posted on May 10, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air bag light flashing,two pause five.It dose this five times and then stays on


You have a code 25 which is a side curtain air bag passenger side. Most likely the connection disconnect the airbag and reconnect it. First disconnect the battery

Oct 28, 2015 | 1998 Ford Ranger SuperCab

1 Answer

How to remove the steering wheel for replacement


SIR DISABLE:
DRIVER SIDE
Many service procedures require the air bag system to be disabled to prevent accidental deployment. The air bag system can maintain sufficient voltage to cause deployment for up to 2 minutes after the ignition switch is turned off, the battery ground cable is disconnected or the DERM fuse is removed. If the inflator module is disconnected from the deployment loop by the following procedure, service can begin immediately without waiting for the 2 minute time period to elapse.
  1. Turn steering wheel so that vehicle wheels are pointed straight ahead.
  2. Turn ignition switch to Lock position and remove key.
  3. Remove air bag fuse from fuse block.
  4. Remove steering column filler panel.
  5. Remove Connector Position Assurance (CPA) and disconnect yellow two-way connector at base of steering column, Fig. 1.
PASSENGER SIDE
  1. Remove air bag fuse from fuse block.
SIR ENABLE:
Driver Side
  1. Turn ignition switch to LOCK and remove key.
  2. Connect yellow two-way connector and install connector position assurance (CPA).
  3. Install steering column filler panel.
  4. Insert air bag fuse into fuse block.
  5. Turn ignition switch to RUN and verify that the air bag warning lamp flashes seven times then turns off.
Passenger Side
  1. Turn ignition switch to LOCK and remove key.
  2. Insert air bag fuse into fuse block.
  3. Turn ignition switch to RUN and verify that the air bag warning lamp flashes seven times then turns off.

remove-steering-wheel-replacement-rfvykuizssn2qn2mhtsbw2yl-3-0.png

Apr 10, 2015 | 1996 Chevrolet K1500

1 Answer

Air bag light on passanger side


More than likely, since the wiring for the passenger side air bag is located right where you were working, you may have disconnected a wire. Start by wriggling the plug in to the air bag.

Apr 19, 2014 | 2000 Lincoln LS

1 Answer

Pcm location 96 passport


old post i do up to 3 months,
with air bags is different than with.
USA answer, LHD , left hand drive, not Right.
no bag, left toe is PCM
yes bags, point finger to radio ,now down past the pocket shelf to store Cassettes or what-nots. bingo PCM and bag brain below
do not fiddly he PCM ever on this bag car, until you read the air bag defeat section in FSM. it can KILL.
here is the quote off the online page.
after key out.


  1. Disconnect the negative and positive battery cables. Wait at least five minutes before working around the Air Bags.
  2. Disarm the Air Bag system. DO NOT SKIP THIS !!!!!
  3. Remove the glove box door and the passenger's Air Bag lower cover.
  4. Disconnect the yellow 2-way Air Bag harness from the passenger's side Air Bag.(the danger point)
  5. Remove the four console screws. Remove the console.
  6. Unscrew and remove the trim panel located below the dashboard cubby hole.
  7. remove the PCM. screws and PCM.

Sep 08, 2013 | 1996 Honda Passport

1 Answer

How do I remove the front soft cover/air bag on a 2003 Chevy Cavalier steering wheel to gain access to the horn components? Does this require a special tool?


Disarming the System

Print

CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before performing many in-vehicle service procedures. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.

  1. Turn the steering wheel so the vehicle's wheels are pointing straight-ahead.
  2. Turn the ignition switch to the LOCK position.
  3. Remove or disconnect the following:

    Ignition key AIR BAG fuse from the instrument panel fuse block Left-hand sound insulator Connector retainer and yellow 2-way connector at the base of the steering column. Right-hand sound insulator, if equipped with passenger side air bags Connector retainer and yellow 2-way connector from the passenger inflator module pigtail, if equipped with passenger side air bags

    0996b43f80208efb.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Driver-s side Yellow 2-way air bag connector retainer location

May 24, 2012 | Chevrolet Cavalier Cars & Trucks

1 Answer

How do I disengage the passenger side air bag on a Lexus 2005 RX 330 SUV for just the day. It's so I can put our granddaughter in the front seat with her car seat.


check in the owners manual. there should be a switch on the dash IF it has one. I recommend the rear seat, its the safest place.

Sep 01, 2011 | 2004 Lexus RX 330

1 Answer

HOW DO I TURN OFF OR ON THE PASSENGER SIDE AIR BAG ?


I don't believe there is a switch, but if you locate the air bag module or air bag box, then disconnect it, then I think that will disable the air bag.

Feb 18, 2011 | Volkswagen New Beetle Cars & Trucks

1 Answer

Need to remove heater A/C dash control , what is proper procedure?


Look at fig. 4 for the heater a/c dash control: HEATER CORE Altima REMOVAL AND INSTALLATION
  1. Position the steering wheel in the straight-ahead position.
  2. Turn the ignition switch OFF.
  3. Disconnect the negative (() battery cable; then, the positive (+) battery cable. NOTE: Wait for a least 3 minutes after disconnecting the battery cables for the charge in the air bag circuit to dissipate before working on the air bag module(s).
  4. Remove the driver's side SRS and steering wheel by removing or disconnecting the following:
    • Lower lid from the steering wheel and disconnect the driver's air bag module connector
    • Left and right side lids from the steering wheel
    • Special bolts from both side of the steering wheel using a tamper resistant Torx wrench (T50)
    • Air bag module and store it face up
    • Horn's electrical connector and remove the steering wheel nut
    • Steering wheel from the steering column using a suitable puller
  5. Remove the passenger's side SRS by removing or disconnecting the following:
    • Glove box door and the glove box
    • Front passenger's air bag module connector
    • 2 special bolts using a tamper resistant Torx wrench (T50)
    • 4 passenger's air bag-to-instrument panel nuts
    • Front passenger's air bag module and store it face up.
  6. Drain the cooling system into a clean container for reuse.
  7. Discharge and recover the air conditioning system refrigerant.
  8. Working in the engine compartment, disconnect the heater hoses from the heater core tubes.
  9. Remove the instrument panel by removing or disconnecting the following:
    • Kick plate and dash side finisher on the driver's side
    • 2 lower panel-to-instrument panel screws and the lower panel on the driver's side
    • 2 lower reinforcement panel-to-instrument panel screws and the lower reinforcement panel
    • 6 steering column cover screws, the covers, the spiral cable and combination switch
    • 2 cluster lid "A" screws and the cluster lid "A"
    • 3 combination meter screws, disconnect the electrical harness connector and remove the combination meter
    • Switch panel
    • Instrument panel lower covers
    • Snap out the transmission shifter finisher (boot)
    • 4 cluster lid "C" screws and the cluster lid "C"
    • 4 audio and deck pocket-to-instrument panel screws and the audio and deck pocket
    • 5 center console screws and the center console
    • 2 center instrument panel screws and the center panel
    • front defroster grilles
    • Front pillar garnish
    • Instrument panel 3 nuts/4 screws and the instrument panel
    • 8 instrument stay assembly nuts and the stay
    • Steering member assembly 5 nuts/1 bolt and the steering member
  10. Remove the air conditioning housing assembly by removing or disconnecting the following:
    • Refrigerant lines from the air conditioning housing assembly
    • Thermo control amp
    • Air conditioning housing assembly
  11. Remove or disconnect the following:
    • Heater unit
    • Heater core from the heater unit Fig. 1: Exploded view of the steering wheel and air bag module 93112gd9.gif
      Fig. 2: Exploded view of the passenger's side air bag module 93112gd0.gif
      Fig. 3: Exploded view of the instrument panel assembly 93112ge1.gif
      Fig. 4: Exploded view of the heater housing assembly and related components 93112ge2.gif
      Fig. 5: View of the heater core and heater housing 93112ge3.gif
    To install:
  12. Install or connect the following:
    • Heater core to the heater unit
    • Heater unit
  13. Install the air conditioning housing assembly by installing or connecting the following:
    • Air conditioning housing assembly
    • Thermo control amp
    • Refrigerant lines to the air conditioning housing assembly
  14. Install the instrument panel by installing or connecting the following:
    • Steering member assembly and the steering member 5 nuts/1 bolt
    • Instrument stay assembly and the 8 stay nuts
    • Instrument panel and the instrument panel 3 nuts/4 screws
    • Front pillar garnish
    • Front defroster grilles
    • Center instrument panel and the 2 center panel screws
    • Center console and the 5 center console screws
    • Audio and deck pocket and the 4 audio and deck pocket-to-instrument panel screws
    • Cluster lid "C" and the 4 cluster lid "C" screws
    • Snap in the transmission shifter finisher (boot)
    • Instrument panel lower covers
    • Switch panel
    • Combination meter, connect the electrical harness connector and install the 3 combination meter screws
    • Cluster lid "A" and the 2 cluster lid "A" screw
    • Combination switch, the spiral cable, the covers and the 6 steering column cover screws
    • Lower reinforcement panel and the 2 lower reinforcement panel-to-instrument panel screws
    • Lower panel and the 2 lower panel-to-instrument panel screws, on the driver's side
    • Kick plate and dash side finisher, on the driver's side
  15. Working in the engine compartment, connect the heater hoses to the heater core tubes.
  16. Install the passenger's side SRS by installing or connecting the following:
    • Front passenger's air bag module
    • 4 passenger's air bag-to-instrument panel nuts
    • 2 new special bolts and torque using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm)
    • Front passenger's air bag module connector
    • Glove box door and the glove box
  17. Install the driver's side SRS and steering wheel by installing or connecting the following:
    • Steering wheel to the steering column
    • Steering wheel nut and torque the nut to 22-29 ft. lbs.
    • Horn's electrical connector
    • Air bag module
    • New special bolts to both sides of the steering wheel and torque the bolts using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm).
    • Both the left and right side lids to the steering wheel
    • Lower lid to the steering wheel and connect the driver's air bag module connector
  18. Refill the cooling system.
  19. Connect the positive (+) battery cable; then, the negative (() battery cable.
  20. Evacuate, charge and leak test the air conditioning system refrigerant.
  21. Operate the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Nov 19, 2010 | 2002 Nissan Sentra

1 Answer

How do you remove or replace the passenger airbag on a 99 contour , Is it a whole dash unit? What holds the drivers bag in the steering wheel? I assumed it was a tork but not sure. Where is the control...


Please rate as fixya if this helps.
the air bag control module is under the console.

  1. Disconnect the battery ground cable.
    1. Wait one minute.
  2. Remove the center console. For additional information, refer to Section 501-12 .
-----------------------------------------------------------------
  1. Disconnect the battery ground cable.
  2. Wait one minute.
  3. NOTE: Contour shown, SVT similar.
    Remove the rear floor console screws.
    1. Move seat fully forward.
  1. Fully apply the parking brake.
  1. Detach the shift indicator selector bezel.
  1. Detach the shift bezel from the selector housing.
    1. Remove three bolts.
    1. Detach shift bezel from the console.
  1. NOTE: The rear floor console must be raised to disengage the front retaining clips.
    Raise and remove the rear floor console.
  1. Remove the four front floor console retaining screws.
  1. Detach the front floor console.
    1. Set the gearshift lever into position 1.
      Partially remove the front floor console.
  1. Disconnect the cigar lighter electrical connections and remove the front center console
-----------------------------------------------------------
  1. Disconnect the air bag control module electrical connectors.
    1. Depress the locking tang.
    1. Slide the locking bar back.
    • Disconnect the connector.
  1. NOTE: The air bag control control module is grounded by the retaining bolts.
    Remove the air bag control module.
    • Remove the three bolts.
--------------------------------------------------------------------------------------------
driver air bag module

  1. Disconnect the battery cables.
  1. Rotate the steering wheel 90 degrees to access and remove the Torx screw. Rotate the steering wheel 180 degrees to access and remove the Torx screws.
  1. Remove the driver air bag module.
    • Disconnect the electrical connector.
    • Remove the air bag module.
------------------------------------------------------------------------------------------
  1. Disconnect the battery cables. For additional information, refer to Section 414-01 .
  1. Open the glove compartment, press the sides inward and lower the glove compartment to the floor.
  1. Remove the passenger air vent duct.
    1. Disconnect the duct from the heater box housing.
    1. Disconnect the duct from the instrument panel register and remove.
29e093f.gif
  1. Disconnect the passenger air bag module electrical connector.
  1. Remove the two retaining bolts securing the rear of the passenger air bag module to the cross-vehicle beam.
14df419.gif
  1. sxp~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the passenger air bag module when removing the retaining nuts.
    Remove the two nuts from the front of the passenger air bag module.
4a697c8.gif
  1. Remove the passenger air bag module.
    • Lower the front edge of the passenger air bag module, roll the passenger air bag module around the cross-vehicle beam lowering it into the passenger footwell.
82a0ae0.gif

Mar 15, 2009 | 1999 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...