Question about 2005 Fiat Palio Weekend

Open Question

Timming marks on cams - 2005 Fiat Palio Weekend

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4jx1 camshaft marks on isuzu trooper 2001 3,0 dohc engine


the timming gear that the belt runs on has a mark (V cut in gear) to rear cover at about 12 o clock and crank pulley has timming mark for top dead centre, both cams have cut outs in rear that a special tool (camshaft stopper 5-8840-2592-0) locks into to hold cams in correct position, but can do without this, if the cam belt gear is off, the keyway should be at 12 o clock. the marks in the camshaft gears (dots) is for assembly of sissor gears to solid gears on camshafts that run together and they should match up only if you had this appart.

stevenhurc_12.jpg no.1 is timming mark

stevenhurc_13.jpgthis is the locking plate tool

Apr 19, 2011 | 2001 Isuzu Trooper

1 Answer

Cam timming marks to set up the timming chain and cam timming.


Should be a dimple or dot on each gear crank one points up cam one points straight down they should line up perfecly.

Nov 09, 2010 | Jeep CJ7 Cars & Trucks

1 Answer

Hey guys I need to get changed the timming belt on my hyundai accent 1995 and I can do it myself but don´t have the timming marks diagram, can you please help me?


if its a single cam the marks should be on the backing plate and if it is twin cam the two marks should face each other on the compression stroke of the number 1 cylinder and the same goes for single cams line the mark up with the backing plate in the compression stroke of number 1 cylinder.

May 27, 2010 | 2001 Hyundai Accent

1 Answer

I have a 2002 dodge stratus..the timming chain was


Something is obviously not proper in the timing case.
Pick up a Chilton's manual,which should give you all the info needed,to rectify your situation. Good luck.

Apr 01, 2010 | 2002 Dodge Stratus

1 Answer

Can not find timming marks on cam gears


Ther are none. It takes a tool to hold the cams in place while the valve cover is removed. Get a chilton book from the library.

Nov 03, 2009 | 2001 Ford Focus

1 Answer

2002 Hyundai Acent 1.5 sohc,need info on cam timming


didnt you mark it before you removed the old belt??

Nov 01, 2009 | 2002 Hyundai Accent

1 Answer

Cam shaft timming marks 1999 Daewoo 1.6 liter


there is a special tool to hold gears in correct place on some of these models, but you can hold one cam at a time with a spanner then feed belt on exhaust cam then inlet cam gear
get someone to hold gears in place while you feed belt on.
the inlet cam is more prone to turn off mark more than exhaust.
if you have tensioner that needs retaining pin in when installing
you fit belt while aligning timming marks
fit tensioner as last spot to feed belt on with retaining pin in adjuster
get correct tension on belt by turning water pump so that you can flex (turn) belt 90 degrees only just while using finger and thumb
tighten water pump check flex
check all timing marks are correct
remove retaining pin from auto tensioner
turn motor over a couple of turns by hand observing tensioner arrow should hover around V mark and that all timing marks align up again(after one complete turn)

Aug 02, 2009 | 1999 Daewoo Lanos

1 Answer

I need to know how to set the timming marks on the 1.6 double over head cams to replace timming belt


timming marks on cams face each other 3 and 9 o clock crank mark at about 6 o clock mark in cover and sump auto adjuster arrow should be in v mark to set this requires turning water pump by loosening water pump bolts slightly be warned some times this causes pump o ring seal to leak if turning.

May 19, 2009 | 2000 Daewoo Lanos

Not finding what you are looking for?
2005 Fiat Palio Weekend Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fiat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Fiat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...