Question about 1998 Jeep Wrangler

1 Answer

Jeep wont start after i replaced crank pos. sensor

Any clues

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 288 Answers

Two things to check first there is an adjustment on that sensor small piece of paper on end of sensor has to contact fly wheel and be torn off at start up adjust to just touch flywheel should do the trick.second is the connector snapped tight. and the wires on those motors are know to have problems just un hook sensor and disconnect battery cable and use a self powered cheap conuity tester on both wires to pcm . u dont need a diagram for this test because the tester will find the wires at pcm if there ok. if you find a open wire open the harness and follow the wire to pcm keep checking along the way with cheap tester dont use a test light ask for connuity tester. hope this helps.it may also need to be resncyed with cam sensor.

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Jeep Grand Cherokee will turns over but wont start


Replace your crank shaft pos sensor. It is located on the driverside top of the bell housing on your tranmission, where the engine meets your ******

Mar 30, 2012 | 2000 Jeep Grand Cherokee

1 Answer

1998 Jeep Cherokee -- car won't start. Turns over


have scanned to find problem code to get an idea of what it is. .it may either be the crank or cam sensor, check the crank sensor first. if it is bad it sends wrong timing info to pcm. therefore jeep will not start!! It is either the camshaft or crankshaft positioner. I would check the crank pos. first. Zach Cabot, AR
It is either the camshaft or crankshaft positioner. I would check the crank pos. first. Zach Cabot, AR
It is either the camshaft or crankshaft positioner. I would check the crank pos. first. Zach Cabot, AR

May 31, 2010 | 1998 Jeep Cherokee

1 Answer

99 Jeep Cherokee Sport, 4.0L -won't start


you need to have it connected to an OBD2 machine and watch if you are missing the cam sensor showing RPMs
or if your missing crank sensors RPMs,
it could be a wiring problem or computer if your seeing the RPMs from both sensors,and the last thing i would check is hooking up a fuel gauge to the reed valve and watch what fuel pressure you have while cranking,if the cam sensor is the culprit it will turn the fuel off after the cranking.

Jan 11, 2010 | 1999 Jeep Cherokee

2 Answers

2001 jeep cherokee cranks but wont start and has


If all the fuses are good,replace the crank shaft sensor,this is the problem.

Jan 04, 2010 | 2001 Jeep Cherokee

1 Answer

Jeep wont start


The crank position sensor is on the bell housing of the transmission, very hard to see, on passenger side, below the valve cover, depending if it is an early 2000 or a later 2000 model.

Mar 31, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Jeep Cherokee won't start, turns off, etc.


Did you have the same cranking with no start problem with original engine or did the problem begin when you changed it? I would check codes if you have not already, and would also clean business end of idle air valve (next to tps) DO NOT turn the end plunger while cleaning or it may not seat properly. Do not loose the rubber "o" ring while working either!

Mar 02, 2009 | 1988 Jeep Cherokee

2 Answers

Starts ok, but if turn of, will not restart


Try replacing the coolant temp switch. The one that sends signal to the ECU. I hope this helps

Nov 14, 2008 | 1994 Jeep Grand Cherokee

3 Answers

1999 jeep tj cranks but wont start


replace the crankshaft position sensor

Aug 16, 2008 | 1999 Jeep Wrangler

Not finding what you are looking for?
1998 Jeep Wrangler Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...