Question about 2003 Suzuki Grand Vitara

Open Question

How can I remove gear shifter knob? - 2003 Suzuki Grand Vitara

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 Buick Riviera


Most likely it's threaded on. Pull the selector all the way down, First gear. If there are any screws they will be visible then. If not, twist off

Apr 07, 2014 | 1995 Buick Riviera

1 Answer

Need to remove a gear shifter from a 2003VW passat


gear shifter as transmission inside it. well best replace transmission or you'll need a pulley and few sockets. as the shift. the shift you pull the knob or act as if you are prying it out it stay out. once out far enough push down on the bottom sparkling part of the stick. once down pull knob. then fallow the screw on side for removal.

Mar 15, 2014 | 2003 Volkswagen Passat

1 Answer

Replace gear shifter knob on s-10 manuel


Most gear shift knobs are just screwed on. Try turning it anti clockwise if yu can not see any screw holding it

Jun 22, 2012 | Cars & Trucks

1 Answer

Having a hard time putting my car in gear. It has to warmm up in order to engage the button on the shifter to put the car in gear.


The shifter knob that houses the button may be worn out or the shifter mechanism may need to be lubricated. You can try spraying a little WD-40 around the shift button and into the shift knob using the straw provided with the spray can.
To lubricate the shifter, the shift knob will have to be removed and the shift plate removed to gain access to the shifter mechanism.
Good luck.

Jan 17, 2011 | 1998 Chevrolet Malibu

1 Answer

Remove shifter knob 1998 pontiac grand prix


Hello! It's best to put the gear shifter all the way back into the 1st gear. After you do this look on the front of the shift knob, just above where it meets the shifter's shaft you will see a horizontal slot - inside this is a clip. You will need a small flat-bladed screwdriver, or a mechanic's pick to pull this clip out, but once it is removed the shift knob will come off by pulling it straight up.


Thanks for using FixYa!

Oct 31, 2009 | 1998 Pontiac Grand Prix

2 Answers

Replacing deawoo kalos gear shifter/ gear knob


do not know the car. but some screw off and others just pull off ask at halfords. they know.

Mar 26, 2009 | 2002 Daewoo Lanos

1 Answer

Gear shifter will not go into park


There is a plastic actuator stick under the shift knob. Remove the "horse shoe" clip from the shift knob and remove knob by pulling strait up. You can twist it right and left a very small amount to loosen the knob, but not much.
Once you have the shift knob removed you will see the plastic actuator stick. Push down on the stick and put shift lever in park. If that works, the shift knob or stick is worn out.
Let me know.
Regard,

Feb 12, 2009 | 2004 Pontiac Grand Am

1 Answer

Gear knob removal bmw 318 ci


It's very simple. Involves a bit of fore arm strenght.
It should pull straight off. Just put one hand around the gear knob & your other hand supporting or gripping with both.
Just pull straight up. It shouldn't need much force. A small amount of glue may have been used to help hold it in place.
The knob might come off leaving the plastic sleeve/insert in the shifter. Same again, just grip that & try pull it off. A vice grips should not be neccessary but if you need it be carefull not to apply too much pressure as you don't want to break the sleeve into pieces.
The new knob should have a sleeve with it. Normally it will be inserted & you should be able to just pop it straight on.
Make sure it's lined up properly. You probably noticed on the bare metal shifter that it has a notch normally running across from left to right. Well inside the knob if you can see in you will notice it has a plastic or metal piece that will fit into this notch. This is to stop the knob from spinning around or slipping!
Just push down on the top of the knob & try slide it over the shifter. It might not go down all the way with pushing so a few taps with you palm may be enough if you have big strong hands but if not be carefull & only use a rubber head hammer or something you can hold but won't mark or break the knob.
Put a towel or old t-shirt over the knob & use anythink heavy that you can hold easily with one hand & that has no sharp edges!
I don't think any glue should be neccessary but if you feel it needs a little & the knob is comming off or going on too easy then just a few drops on the sides of the bare metal shifter before sliding the knob back on should suffice!
Good luck!

Dec 14, 2008 | 1999 BMW 318 ti

1 Answer

Removal of gear shift knob


There are two types of shift knobs. One that unscrews and one that the lower trim of the shift knob separates from the knob using a trim stick. After separating the lower trim from the knob pull upward to release the knob from the shift lever. If a new shifter assembly is being installed, unscrew the original shift knob or separate the lower trim from the knob and pull up to remove the knob from the shift lever. Screw the knob onto the new shifter assembly's lever no more than 14 turns or install the lower trim onto the shift lever then push the knob onto the shift lever and install the lower trim piece onto the shift knob.

Jul 02, 2008 | 2007 Dodge Magnum SRT8 Wagon

Not finding what you are looking for?
2003 Suzuki Grand Vitara Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...