Question about 1987 Toyota Corolla 2 Door

2 Answers

Starter i can,t locat the starter wear would it be

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 2,984 Answers

Starter REMOVAL & INSTALLATION

  1. Disconnect the negative battery cable.
  2. Disconnect the cable which runs from the starter to the battery at the battery end.
  3. If necessary, remove the air cleaner assembly in order to gain access to the starter. NOTE: On some models with automatic transmissions, it may be necessary to unfasten the throttle linkage connecting rod.

Posted on Jun 23, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 366 Answers

Frt of motor where tranny mates with motor.

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do U locate the starter on a 08 Dodge avenger? How do you replace the starter on an 08 Dodge avenger?


Under the car, beside the engine, on the drivers side. Disconnect the battery first. Three bolts hold it on. Two wires to remove. It is a tight area to work and is a pain to get it out, but it will come out. Watch as it comes out because that is the only way to get it back in. Also there is a shim that HAS to go back between the starter and transmission. If not, the starter will wear out fast. Could take out the flywheel also.

Feb 20, 2016 | Dodge Cars & Trucks

1 Answer

Can anyone tell me where I can locate the starter? A picture would be extremely helpful. Thank you


The starter motor is always attached to the gear box at the end wear it connects to the Engine, depending on you care transmit ion system, if it's manual it's on the clutch end sometimes on older cars called the bell end due to it's shape , the Automatic gear box is the same but contains a fluid torque converter, the starter motor locates into the large ring gear that sit around the outer edge of the clutch flywheel assembly on both types of gear box's, hope this is of some help to you.

Good Luck

Mar 06, 2015 | Cars & Trucks

1 Answer

My starter make this grinding noise when i crank it


Usually, this means you have a worn gear on the starter, the starter is loosely mounted, the starter solenoid is malfunctioning, or the flywheel has a worn spot on it. First check to see that the starter is mounted correctly (and all bolts are tight). If tight, and you can remove the starter, check the teeth on it for wear. If no wear is present, have the starter tested for the solenoid functionality. While the starter is removed, check the flywheel for a missing gear tooth or for obvious wear.

Feb 16, 2014 | 1999 Mercury Villager

1 Answer

Shim location


Shims can be where the starter case meets the bell housing. There are not many models using shims anymore, they were used a lot in GM vehicles, not so much in Ford products.
The gear on the starter drive needs to mesh with the flywheel teeth. Sometimes a starter would rock loose in its mount and wear the starter case or the bell housing. When you try to align the 2 parts, it would throw off the mesh of the gears and teeth. The shims are usually patterned after the shape of the facing of the parts. You may need to go to the Dealer for these shims.

Jun 09, 2013 | Mercury Cougar Cars & Trucks

1 Answer

1994 Camry 4 Cylinder-Starter spins fine but does not seem to engage the flywheel. I have a new starter and battery. Im not ready to get into the flywheel. What else can I test to see why its not engaging...


Well, the easiest solution is to pull the starter and bench test it. Likely areas for your issue is the starter drive, and flywheel teeth. You need to inspect the teeth of the flywheel.

one quick test would be to manually turn the engine to another location and fresh teeth on the flywheel, and try starting again. Engines tend to stop at some spots, and that can cause unusual wear on teeth in one small location.

Sometimes rebuilt starter do not get all new parts, but only what is failing, so it is possible to get a malfunctioning starter drive. Starter drive failure usually turns the engine over briefly, then the starter disengauges....

Feb 05, 2011 | 1994 Toyota Camry

1 Answer

Starter won't turn but lights stay bright when ignation is activated


With the ignition off, locate the starter, use a handle from a broom or hammer and give the starter a whack. Try this a couple of times, it may get it going. Over time the "brushes" wear and the resulting dust coats the little copper contacts, this in turn insulates it so no current will pass and the starter will not turn. It may work a few times before it plugs again, so look into getting ready to purchase a rebuild or new starter.

Dec 28, 2010 | 2000 GMC Safari

1 Answer

Lol where abouts is the starter motor located for a cc lancer located


most starters are located on engine wear it mounts to transamision//or go to auto zone .com look 4 a pic.or if it runs take it in a quick lube tech. could point it out.if you would like more info please feel free to ask with more detail .thank you 4 using fix ya.

Jun 10, 2010 | Mitsubishi Lancer Cars & Trucks

1 Answer

Replaced starter now grinds


Loosen the starter bolts and push it away / reposition it farther from the flywheel (circumference) then retighten the bolts. Then try it again. It is rare that a rebuilt starter is defective but... it does happen.

Kelly

Mar 11, 2010 | 1995 Nissan Altima

1 Answer

Got spark and fuel put a new starter in car wont start. Could it be a cam sensor if so where is that located on the car?


Unless the cam sensor is totally shattered which is rare that won't have a lot of effect.(it wears yes) On the 3800 90-94 models it is located bottom of motor left side as you face motor (very difficult location)
On the starter its possible your solenoid was the culprit in the first place.Did the starter come with solenoid attached ?

Mar 02, 2010 | 1986 Buick Regal

2 Answers

Changing the starter in a 1994 Toyota Corrolla


you need to remove one bolt from the top and the other from the bottem. also the wires are removed from the bottem. most likey the starter if factory is still good the starter contacts wear out they are under the cover on the back of the starter.

Apr 18, 2009 | 1994 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...