Question about 1993 Daihatsu Applause

Open Question

93 applause wont go into overdrive

Car drives fine, tends to shift up early but cable adjustment on throttle to gearbox has little effect. Pressing overdrive button shows up on dash but simply wont go into overdrive, oil level ok and fully warmed up. any ideas?

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Shifted fine changed motors now won't shift to drive or overdrive


check that you have connected correctly the cables for the torque converter solenoid / servo unit as it may not be making good contact after the engine change . Also as the battery was disconnected for a time I would use a scanner to reset the CPU program as the program may be corrupted from the lost battery power.

Mar 22, 2014 | 1983 Chevrolet Silverado

1 Answer

Overdrive


Check detent cable adjustment at throttle body.

Mar 20, 2014 | 1992 Ford Mustang

1 Answer

2003 Ford ZX2 automatic transmission will not drive in drive or overdrive when at a stop light. But will move is first gear.


check your linkages from your gear stick to the gearbox .need adjustment.and check the kick down cable ,at the throttle needing adjustment.

Oct 02, 2012 | 2003 Ford ZX2

1 Answer

Crown victoria 1989 kick down assembly


There a tab at the linkage you unlock it and slid the cable till it is just a little loose the snap the tab back in, drive the car and make a note when the car shifts into overdrive, it should do it at about 55 miles per hour at half throttle, if it shifts to fast tighten the cable if it stays out of overdrive loosen it

Aug 22, 2012 | Ford Cars & Trucks

1 Answer

Transmission wont go into 3rd or overdrive but shifts fine from first to second


Sounds like the direct clutch is bad. But first make sure the transmission control cable is still attached to the throttle body. If it isn't replace the bushing that holds it on, they tend to break. If it is hooked up the transmission will need rebuilt.

Mar 08, 2011 | 1988 Mercury Grand Marquis

2 Answers

93 Mitsubishi 3000gt overdrive problem


I think rebuild try and service it if you find any lining material in the pan bad news

Jun 06, 2010 | 1993 Mitsubishi 3000GT

1 Answer

1990 f150 transmission up shift to early


Sounds like the passing gear cable is out of adjustment. Get a shop manual and see what the specs are on how to adjust it properly. It is a pretty simple fix.

May 27, 2009 | 1990 Ford F150

1 Answer

Drive or overdrive dont engage


sounds like you need the gearbox looked at.... the adjuster pulleys in the in the gearbox are loose.. hope this helps

Apr 07, 2009 | 1994 GMC Sierra

2 Answers

Dodge ram p/u overdrive issue


Grinds as in slowly creeps? or grinds as in metal noise?
Not shifting into overdrive,could be the kick down bands need adjusted.Or the kick down cable.

The cable is on the Throttle body side and should be lined up perfectly with the lug it goes on. Make sure you are not pulling on the cable or you will get a false indication of where it is. It has to be lined up with in a 32nd of an inch.. This is the baseline of where it would be in stock form. If you have it set like this and it wont shift until you let of it a little bit, then you need to loosen the cable a little bit. If you loosen it too much, you will have other problems..such as shifting too soon/late. It takes a while to get it how you want it. Start with making bold adjustments, you wont hurt anything, and see what it does. After you have a grasp as to what it doesn when you move the cable in either direction, make smaller adjustments..

You dont need a "tranny guy" to do this for you. If you dont know how to adjust the cable let me know and I or someone else on here will let you know how to do it, its.

Please rate this a fixya with the blue button

Feb 09, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

1999 ram auto trans wont shift into park


you could need a throttle linkage adjustment. first check to see if your ram will start in "park" and "neutral" only. if it starts in any other gear=faulty neutral safety switch. replace. ok, now check linkage for proper adjustment...with engine off and in park...remove intake housing..disconnect cableend from attatchment stud on your throttle body..slide cable off the stud (carefully)..verify that the transmissionthrottle lever is fully forward (idle) position..and verify that the lever on the throttle body is at curb idle pos..insert small screwdriver under edge of the retaining clip and remove..center the cable end on attatchment stud to within 0.04", or 1mm. install retaining clip onto cable housing..check cable adjustment..be sure trans throttle lever and throttlr body lever move in sync with each other.

Jan 11, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
1993 Daihatsu Applause Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...