Question about Chevrolet Venture

1 Answer

97 venture van. Manual front door window cranks up crooked.I have to pull it up straight by hand while cranking! is there a repair? I have the panel off already. Thanks a bunch:)

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Chevrolet Master
  • 3,854 Answers

Your window track could be loose or misaligned. You have the panel off already so that's good, crank the window up and down and look at the window going up and down the side tracks and look for any broken, loose or misaligned window track. If the track's are broken or worn, replace them and realign the tracks if needed. Good luck and hope this helps. 

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to replace the passengers side, front door window crank and assembly, the window will not roll up, I pulled the door panel and seen the cable laying in there, it appears to have a broken plastic...


The mechanism is called a window regulator and you have to replace the entire unit if a plastic piece broke that supports the cable. The mechanism is bolted to the door. alldatadiy.com is a great pro grade shop manual.

Jul 27, 2017 | 2003 Dodge Neon

1 Answer

How do i remove the wing mirror (power adjust & power fold) on the ford f250 super duty?


Roll the window down first, you will need 2 hands. Pull the small cover off that is at the top front of the door pannel. You will then disconnect the wire connector and remove the three 11mm nuts that are holding the mirror in place. Pull mirror out and replace.

If you dont have just that little pannel you will have to remove the door pannel. If you dont have power windows pull the cover out on the window crank and move it to the side, there will be a screw holding the crank in place. Remove it. If you do have power windows remove the window control switch plate (it will just pop up using a small screwdriver) and disconnect the wires. If equipped, remove the front door trim panel reflector or the courtesy lamp lens. Then remove the screws. DO NOT pull directly outward on the door pannel, something will brake. Remove the front door trim panel by pulling it straight upward.Lift and remove the front door trim panel. Then the nuts holding the mirror will be visible, remove and replace the mirror.

Dec 07, 2010 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

How do i remove the front door panels without damaging them?


There's a few tools you'll need:
panel removal tool $7-$10 (forked)
hand crank windows you'll also need a window crank removal tool
screw drivers - philips and small straight
Note pad and pen or pencil
zip lock plastic bag
May need:
socket set
allen and torx drivers

Use the note pad to make notes where everything goes.
Open the door all the way.
Use the straight screw driver to pop any small plastic covers off.
remove any screws that are holding the panel or arm rests or anything else attached to the door (this is where the socket, allen or torx drivers may come in handy)
put all the small part in the plastic bag.
starting at the bottom back corner start gently pulling the panel, you'll soon find spots where it's sticking, here you'll find plastic panel attachment pins. Using your panel removal tool, slide it under the panel and find the panel pins, slide the tool around the pins and pry them loose, You may find an extra screw you missed or a few panel pin toward the center, remove as before.
The panel should now be hanging by where it clips over the window edge (if working indoors, putting the window down ahead of time helps here) gentle lift and pull the panel up and off where it's hanging.
All that's left is disconnecting any wires, there will be clips molded into the sides to hold them in place, gently lift the clip and disconnect them.
Your panel should be loose.
Reverse to reinstall.


Jun 13, 2010 | 2008 Pontiac Grand Prix

1 Answer

How to remove a door panel on a 1995 pontiac grand


I have info on a 96 power door glass.....should be very simular. the triangle piece at the top front is just clipped on, the plastic piece around the opener handle is just clipped on. in the pull handle there are two screws, and the plastic piece just pops up. under the red reflector the is a screw. There is a "U" clip behind your window crank, remove this clip and the crank will pull straight out. (use a screw driver to open the gap between the crank and the door panel, to see the clip, Use a hook tool too remove the clip...you can also use a cloth or panty-hose in the gap and turn the crank, the cloth will grab the edge of the clip and pop it off)
after removing all the clips and screws the door panel is held on with plastic plugs, just pull the panel sraight out toward youself.
hope this helps.


14e9333.jpg
4604e0c.jpg

Apr 01, 2010 | 1995 Pontiac Grand Am

1 Answer

Stuck crank window, drivers side, 97 honda civic


1996-00 Civic 2-doors had a problem with the front windows binding or coming out of the run channel. The window regulator needs replaced and the rubber run channel needs inspected for damage and to make sure its properly seated into the window channels. note: make sure you install the window crank in the 10 o'clock position, so your not tempted to use the window crank as a door handle to pull the door shut. This can break the crank and/or the regulator. -Hope this helps:)

Jan 24, 2010 | 1997 Honda Civic

1 Answer

How to remove rear door panel on 95 taurus


According to the Haynes book, remove window crank or pry off electronic control assembly. With a large screwdriver or pry bar, disengage the clips along the bottom. Once clips are disengaged, swing panel out from bottom and then pull the panel front edge straight out of the door so it clears the molded-in guide pins. Lift the panel straight up and disconnect any electrical connections. Should be done.

Nov 18, 2009 | 1995 Ford Taurus

1 Answer

I'm looking for a picture of the front window track. I don't know how it's supposed to look the window goes down when you turn crank a little bit then have to pull it back by hand


There is a plastic tab on the window that keeps it on track and straight. Sometimes they snap off. So if it's going up crooked this would be the first thing I check. Hope this helps.

Jul 31, 2009 | 1990 Chevrolet Lumina

1 Answer

Removing door panel of manual crank 2000 VW Beetle


Your window crank is held on by a clip at the base of the crank handle. You need a small hook (kind of like a knitting needle) to get behind the base and pull the clip off of the crank.

I hope this helps you, and I wish you luck on your repair.

May 13, 2009 | 2000 Volkswagen Beetle

2 Answers

Remove door panel on a Ford Van


For a 1999 Ford Econoline 150 (assume the same or very similar), remove triangular plastic cover over mirror assembly by prying straight out, remove plastic door handle cover by prying up from the front side, remove electronic door switches by prying up from back side, remove round plastic cover at bottom rear of door panel. Four screws are now revealed, remove them. Lift door panel straight up, clips are hooks (not snap in). Work door switch assembly out of door panel. Set door panel aside. Reassemble in reverse order.

May 09, 2009 | 2000 Ford Econoline

1 Answer

Change window gear on 99 civic


this is from a 97 civic should be the same. remove the door panel. remove 1 screw and pull handle, remove 1 screw and plastic cover over door opener handle. remove speaker cover and three screws underneath. remover window crank. then remove the door panel (held on with plastic plugs...just pull panel toward youself).
8e9dc4a.jpg
e838839.jpg
to remove the regulator ("window crank gears") Remove the glass held in with two 10mm bolts. The regulator itself is held in with six 10mm bolts. Remove these bolts and remove the regulator. (installation is reverse). Note: pay attention to the Idler arm track (highlighted in green) I think this one is directional (the front has to be at the front and the back has to be at the rear)

5a5e384.jpg

Feb 23, 2009 | 1999 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

326 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...