Question about 2006 Dodge Ram 3500 Truck

Open Question

DODGE DURANGO HOW TO RESET TIPM - 2006 Dodge Ram 3500 Truck

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2011 dodge caravan no front turning signals after tipm replaced

Hello Howard,

Is the TIPM a new unit, or salvaged from another vehicle? If salvaged, there may be corrosion (very common) with the PDC (Power Distribution Control). This can prevent proper power distribution to lighting, among other things.

If the TIPM is new, then we will have to look elsewhere.


Feb 17, 2018 | Dodge Cars & Trucks

2 Answers

My 2011 ram big horn 4x4 automatic indicator won't go to drive function. Goes to 4.engine light scans a po882 and po883 code. Tipm problem reset to fix?

codes refer to transmission control module problems === causes wiring --poor connections ---short to ground -- wiring short to positive - TCM
check the condition of the wires at the box and the connections for loose, water and corrosion , then replace the TCM unit

Sep 10, 2016 | Dodge Ram Cars & Trucks

2 Answers

I have a 2007 dodge caliber 2.0L the low beam headlights work but the high beams do not cant find a relay or a wiring digram how to fix them

There isn't a relay , headlamps are controlled by the TIPM - totally intergraded power module (electronic module ) Dodge TIPM low beam repair Same for high beam

Aug 25, 2016 | Dodge Cars & Trucks

1 Answer

Why does my 2012 dodge ram 1500 fuel pump stay on...

About 117,000 results (0.73 seconds) Search Results

    TIPM Repair & Bypass Solutions for 2007-2014 Dodge ...
    2011-2012 Dodge Ram 1500; 2011-2012 Dodge Ram 2500; 2011 Chrysler Town ... test your fuel pump relay, and bypass a bad fuel pump relay to stay on the road. .... Mytesting/bypass device will often narrow down your problem to the TIPM ...

    Dodge Ram 1500 Questions - fuel pump keeps running ... > Questions > Dodge > Ram 1500

    CarGurusNov 1, 2013 - fuel pump keeps running when key removed - 2011 ram 1500 slt quad ...fires right up but will not stay running unless I keep my foot on the gas.

    I Changed The Fuel Pump On My 97 Dodge Ram 1500. Ran ... > Questions > Dodge > Ram 1500

    CarGurusI changed the fuel pump on my 97 dodge ram 1500. Ran great for 2 days then stopped running. I can hear pump working, replaced fuel system relay, engine tur... ...Jun 24, 2012 at 03:48 PM about the 1997 Dodge Ram 1500 2 Dr ST 4WD ... The truck fires right up but will not stay running unless I keep my foot on the gas.

    2011 Dodge Durango Fuel Pump Relay Stays Engaged ...

Feb 03, 2016 | Dodge Cars & Trucks

1 Answer

Location of Ac compressor relay on 2010 dodge avenger

The A/C compressor relay is an integrated circuit within the Totally Integrated Power Module (TIPM). The TIPM is located in the left front corner of the engine compartment and contains serviceable fuses only. If the A/C compressor control circuit inside the TIPM is found to be faulty it can only be repaired by replacing the entire TIPM assembly.


I’m happy to assist further over the phone at

Aug 26, 2015 | Dodge Cars & Trucks

1 Answer

I have no voltage coming out of the TIPM for the left rear turn signal. Can this problem be remedied by having the TIPM reset

Had the same problem. Resetting the TIPM will not solve your problem. Your TIPM can only be reset 5 times, after that that you will have to buy another one for $1200.00 + $400.00 for the instal which include the re-flashing.

The circuitry portion of the TIPM that control your left turn signal is dead. You will have to have a mechanic by-pass it or you will have to buy a new TIPM.

Sep 08, 2010 | 2006 Dodge Ram 2500

1 Answer

Where is the tipm located on teh 2004 dodge ram 1500?

I quote from the service manual:

"The Totally Integrated Power Module (TIPM) is a combination unit that performs the functions of the Power Distribution Center (PDC) and the Front Control Module. The TIPM is a printed circuit board based module that contains fuses, internal relays and a microprocessor that performs the functions previously executed by the FCM. The TIPM is located in the engine compartment, next to the battery and connects directly to the B+ cable via a stud located on top of the unit. The ground connection is via electrical connectors."

This link also provides interesting info on reflashing (re-programming) Dodge Ram TIPM module.


Jul 25, 2009 | Dodge Ram Pickup 1500 Cars & Trucks

1 Answer

2000 Dodge Durango

All you need to do is Remove the POSATIVE cable from the battery for about 25 seconds then reconnect it. This will reset the computer and everything else!

Jan 18, 2009 | 2000 Dodge Durango

1 Answer

Tail light is not working.

if you have a trailer that you tow it has a short and the tipm will shut off power to that circuit. you can only have this reset 3 times by the dealer and if the problem is not corrected the tipm will need to be replaced and its expensive. make sure the short is repaired before having the dealer reset the tail lamp circuit

Jan 08, 2009 | 2005 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides