Question about 2003 Ford Ranger Regular Cab

Open Question

Where is the egr pressure feedback sensor located on a 1999 ford ranger xlt 2.5l

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: O reading for O2 sensors on 98 Ranger XLT

Yes the 98 ranger has 3 02 sensors,they are located in the exhaust system under vehicle,2 of them
are in front of the cataletic converter and 1 behind it.I replaced mine ,reset the codes and the check
engine light still comes on?

Posted on Jan 19, 2009

Ad
the recycler
  • 22 Answers

SOURCE: need location of the erg sensor 2000 ford ranger

The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Posted on Feb 25, 2009

the recycler
  • 22 Answers

SOURCE: location of the egr sensor on 2000 ford ranger

The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Posted on Feb 27, 2009

seans46
  • 161 Answers

SOURCE: location low pressure port a/c 2000 ford ranger 3.0

I am not sure I thought some of them were on the back of the compressor which makes it hard to see . but one thing for sure follow the low press line towards the evap and you will find it

Posted on Jun 09, 2009

  • 532 Answers

SOURCE: I need to locate the canister purge valve and the

look above the spare tire under the back of the box

Posted on Oct 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where egr dpfe sensor is located on a 2000 ford taurus


The EGR is on the Differential Pressure FEedback system. The EGR is located on top middle of the backside of the engine It is round and has a hose attached to it.

Sep 03, 2014 | 2000 Ford Taurus

1 Answer

How do i replace a egr pressure feedback sensor on a 1999 ford ranger


it maybe a metal sensor, which has been replaced with a plastic sensor. not hard to change, however make sure the two hoses are in good shape, no cracks etc. may mount with two 7 mm screws. be careful...jim

May 09, 2014 | 1999 Ford Ranger SuperCab

1 Answer

1401 egr code


P1401 FORD - DPFE Sensor Circuit High
Faulty Differential Pressure Feedback Electronic (DPFE) sensor
- Differential Pressure Feedback Electronic (DPFE) sensor harness is open or shorted
- Differential Pressure Feedback Electronic (DPFE) sensor circuit poor electrical connection. This is not likely the EGR but the EGR pressure sensing valve.

Oct 19, 2012 | Cars & Trucks

2 Answers

Need to find and replace the DPFE-15 sensor. Dealership diagnosed when service engine light came on and saaid this is what needed replacing. Problem is I do not know where to find it on the engine.


Exhaust Gas Recirculation (EGR) System The exhaust gas recirculation (EGR) system is designed to:
  • reintroduce exhaust gas into the combustion cycle.
  • lower combustion temperatures.
  • reduce the formation of oxides or nitrogen (NOX).
The amount of exhaust gas reintroduced and the timing of the cycle varies by calibration. Timing and volume are controlled by the following:
  • engine rpm
  • engine vacuum
  • exhaust system back pressure
  • engine coolant temperature
  • air charge temperature
  • throttle position
The EGR valve (EGR valve) (9D475) is vacuum-actuated. The vacuum hose routing diagram is shown on the Vehicle Emission Control Information (VECI) decal. The EGR system is a differential pressure feedback EGR Sensor system. Differential pressure feedback EGR Sensor is a subsonic closed loop EGR system. The differential pressure feedback EGR system:
  • monitors EGR flow rate by the pressure drop across the metering orifice located in the EGR tube.
  • uses a differential pressure feedback EGR sensor as the feedback device.
  • uses the EGR valve only as a pressure regulator, rather than a flow metering device.
  • controlled pressure is varied by the valve movement using vacuum output of the EGR vacuum regulator solenoid (9J459).
  • allows for a more accurate assessment of EGR flow requirements.


Differential Pressure Feedback EGR Flow Diagram


aa3104a.gif

Differential Pressure Feedback EGR Sensor Removal
  1. Disconnect engine control sensor wiring (12A581) from Differential Pressure Feedback EGR Sensor.
  1. Disconnect Differential Pressure Feedback EGR Sensor hoses from EGR valve to exhaust manifold tube (9D477).
  1. Remove retaining nuts or bolts (depending upon application) and EGR Differential Pressure Feedback transducer.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten retaining nuts or bolts (depending upon application) to 5-7 Nm (45-61 lb-in).


    Differential Pressure Feedback EGR Sensor, 3.0L (2V) Engine


    aa0036a.gif



    Differential Pressure Feedback EGR Sensor, 3.0L (4V) Engine


    a23840a.gif


    Item Part Number Description 1 6049 RH Cylinder Head 2 - Differential Pressure Feedback EGR Sensor 3 - Nut (2 Req'd) 4 - Stud Bolt 5 - Bolt (2 Req'd) 6 - Differential Pressure Feedback EGR Sensor Bracket A - Tighten to 5-7 Nm (45-61 Lb-In) B - Tighten to 8-12 Nm (71-106 Lb-In)

    Engine Emission Control Component Location-3.4L SHO Engine


    a25013a.gif


    Item Part Number Description 1 95607-05200 Nut 2 - EGR Sensor Hose 3 - EGR Sensor Hose 4 95027-08016 Bolt 5 - Differential Pressure Feedback EGR Sensor 6 9J433 Differential Pressure Feedback EGR Sensor Mounting Bracket 7 9D474 EGR Solenoid Vacuum Valve (2 Req'd) 8 A4670 Vacuum Tube Assembly 9 9424 Intake Manifold 10 9J459 EGR Vacuum Regulator Solenoid A - Tighten to 5-7 Nm (45-61 Lb-In)
Hope this helps

Aug 14, 2011 | 1999 Ford Taurus

1 Answer

I have 1999 ford ranger 3.0 flex fuel. 109,000 miles. i get a code reading of p1400. is that a sensor problem or some kind of valve. and can you give a cost for repair estimate. thanks ...


The code P1400 reads "DPFE Sensor Voltage Low" (Ford, Mazda). Often it's caused by a bad DPFE sensor or clogged EGR passages. DPFE stands for (Differential Pressure Feedback EGRI) I would clean the EGR valve which cost nothing. If that does not cure the problem, you may need to replace the DPFE sensor, which does cost, and it may not fix the problem. If you want to be sure you replace the correct part, then visit your local Ford dealer.

Feb 14, 2011 | Ford Ranger Cars & Trucks

2 Answers

EGR DP sensor location on a 1999 mercury sable 3.0 engine


This sensor delta pressure feedback sensor for the egr is located on the top right side of the intake manifold, heres a diagram that will also help in locating this sensor, hope this is helpful. johnjohn2_12.gif

Nov 07, 2010 | 1999 Mercury Sable

2 Answers

I need to locate the canister purge valve and the


look above the spare tire under the back of the box

Oct 21, 2009 | 1996 Ford Ranger SuperCab

2 Answers

Need location of the erg sensor 2000 ford ranger


The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Feb 24, 2009 | 2000 Ford Ranger SuperCab

2 Answers

Location of the egr sensor on 2000 ford ranger


The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Feb 24, 2009 | 2000 Ford Ranger SuperCab

1 Answer

O reading for O2 sensors on 98 Ranger XLT


Yes the 98 ranger has 3 02 sensors,they are located in the exhaust system under vehicle,2 of them
are in front of the cataletic converter and 1 behind it.I replaced mine ,reset the codes and the check
engine light still comes on?

Jan 16, 2009 | 2004 Ford Ranger

Not finding what you are looking for?
2003 Ford Ranger Regular Cab Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...