Question about 2000 Mitsubishi Eclipse

1 Answer

I need to change my quater panel and are no how

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

Front or rear? The front one is easy and can be done with a ratchet and a 10mm and 13mm socket. there are bolt all along the top edge where it meets the hood, the hood hinge will have to come off along with the headlight and front bumper. there is alson a couple of bolts that are on the very bottom of the fender and the inner splash shield inside the wheel well will have a bunch of plastic clips that will have to be taken out. As for the rear one, it is welded on and will have to be cut off. I would not recommend you do this yourself unless you have experiance with cutting and welding

Posted on Jun 23, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Have problem with sender unit,it sticks at quater full,gives false reading miles left,

most likely you will need to pull fuel pump assembly. might as well change the whole thing once in there and it was save time later

Oct 15, 2014 | 2005 BMW X5

1 Answer

My 2002 vx cabrio top wont go down or up but the motor works and im told it might be the hydraulic fluid that needs to be filled, where in the car is that located so i can properly fix the problem without...

pump is in trunk on drivers side.remove side panel.reservoir has level indications.unscrew brass cap and refil with 10w30 oil.if a hose is leaking it will cost you 325.00 cdn.for a new hose with fittings. however i changed one for 30.00 bucks by sijver soldering one quarter inch steel pipes 4 inches long to existing fittings at both ends of the hose and installed one quater inch 300 lbs clear plastic hose.Works number one.

Aug 04, 2011 | 2001 Volkswagen Cabrio

1 Answer

I need initial setting for idle mixture adjustment for Motorcraft 4180C carburator

one and a quater to one and half turns out ,or so i was taught at college 40 yrs ago and they never changed much till the advent of fuel injection

Feb 04, 2011 | Ford F-250 Cars & Trucks

1 Answer

1994 toyota carolla with big dent on driverside back quarter panel, is it one big piece or is it a quater panel?

Quarter panel , it's quite a job. Ask the body guy to show you your car when he's in the middle of the job.. You will have a better understanding ..

Jan 03, 2010 | 1994 Toyota Corolla

1 Answer

I have a need for interior side panel for a 1998 dodge durango. The part is needed for the panel below the far rear window but I'm not sure what I should be asking for.

you ask at a junk yard for the inner rear quater pannel insdie below rear window passenger side or driverside so they get the correct side.

Aug 14, 2009 | 1998 Dodge Durango

1 Answer

2007 quarter panel

Any body shop has a great big book with those pics in it. Say pretty please.

Jun 15, 2009 | 2007 Cadillac SRX

1 Answer

How to replace 1997 Toyota Camry dashboard lights?

Not a quick job. You need to remove the instrument panel. once removed the bulbs simple twice a quater turn and you can replace them. removing the instrument panel varies on different cars, often you can do it without removing the steering wheel. You would normally take off the plastic under the steering wheel. lower the steering wheel as far as it will go. there should then be screws holding in the plastic around the instrument panel.

Jun 15, 2009 | 1997 Toyota Camry

1 Answer

How do I pacth a quater and rocker panel?

Believe it or not, autosupply places now sell replacements, that are sheet metal, already formed to the shape you need for easy installation in this case, and are very reasonably priced for quick low cost repairs. If yoou want to do it on the cheap, rivet them on.

Feb 28, 2009 | 1990 Dodge Dynasty

1 Answer

1999 corvette c

Very easily, take off the passenger side tailight (outter) two screws/torque bit. Once you have done that reach in on the inner quater panel you should be able feel the antenna....... (To remove anntenna). From the outside of the anntenna on top where the actual anntenna comes out there is a ring silver or balck. You should be able to twist (unscrew) that ring to loosen the antenna and two more on the in side of quater panel. The anntenna should drop from the inside of the quater panel. Hope this helps!!

For visual instructions go to: #17

Aug 02, 2008 | 1999 Chevrolet Corvette

1 Answer

Remove Driver's door and quater panel

Hey you can do it by the following the instruction given in this link:,1965001/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c15280038475

PS Dont forget a fixya rating!

Have a good day...

Jul 17, 2008 | 1995 Mitsubishi Diamante

Not finding what you are looking for?
2000 Mitsubishi Eclipse Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides