Question about 2007 Chevrolet Uplander

Open Question

Position capteur vilebrequin - 2007 Chevrolet Uplander

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a csmshsft sensor on a 2008 cadillac srx


Before you replace a part you may or may not need . Why ? What code ? Does the vehicle run ? There has been a lot of confusion on these vehicles with variable valve timing , mixing up cam sensors with camshaft actuators
DTC P0008: Engine Position System Performance Bank 1

DTC P0009: Engine Position System Performance Bank 2
The presence of DTCs P0008 and P0009 along with P0016, P0017, P0018, and P0019 indicates a possible condition with the primary timing chain and the alignment between both intermediate sprockets and the crankshaft. Or, the crankshaft reluctor wheel has moved and is no longer referenced to top dead center (TDC).


?€¢
Observe the scan tool CMP Desired, Actual, and Angle Variance parameters before a DTC sets. This may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.



DTC Descriptors
DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0020: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P0023: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P2088: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2089: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2090: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2091: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2092: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2093: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2

DTC P2094: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2095: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0342: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0343: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0346: Intake Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0347: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0348: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0367: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0368: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0391: Exhaust Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0392: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0393: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
I'm sorry but when dealing with these problems your best bet is to take your vehicle to a qualified repair shop , I have never see a DIY'ER correct the problem with these , an in the end always end up taking it to the dealer .

Jul 24, 2016 | 2008 Cadillac Srx

1 Answer

Where is the crankshaft position sensor on my 2010 srx 3 liters


Camshaft/Crankshaft Position Sensor Replacement - Cadillac Forums

www.cadillacforums.com/.../261074-camshaft-crankshaft-position-senso...

May 29, 2012 - 8 posts - ‎4 authors
I have a 2004 CTS - 3.6L and am trying to get the camshaft position ... at my local Auto Zone and it simply shows camshaft position sensor A. Code P0340 Camshaft Position Sensor
14 posts
Mar 23, 2013
How to change the camshaft and crankshaft position ...
6 posts
Oct 9, 2011
Where is camshaft position sensor on 2003?
7 posts
Dec 28, 2009
Crankshaft Position Sensor 3.6L 04 CTS
5 posts
Jul 15, 2008
More results from www.cadillacforums.com

2004 Cadillac DTS crankshaft position sensors - YouTube

? 3:22
https://www.youtube.com/watch?v=jbjLJZzF3xA
Sep 16, 2013 - Uploaded by Rogelio Cervantes
Quick overview crankshaft position sensor replacement for a 2004 Cadillac DTS 4.6 liter North Star. ... 2003 Cadillac CTSCrank Position Sensor Part 3 Done!!! - Duration: 8:21. 2LateIWon 8,433 views. 8:21. How To Check .

Jan 16, 2016 | Cars & Trucks

1 Answer

Where is the crankshaft position sensor?


    Pontiac G6 Crankshaft Position Sensors - AutoZone

    www.autozone.com/1/.../pontiac-g6-crankshaft-position-sensor...
    AutoZonePontiac G6 Crankshaft Position Sensors including Crankshaft Position Sensor - Duralast (SU8213), Crankshaft Position Sensor - Duralast (SU9540), Crankshaft ... images for pontiac g6 crankshaft position sensor

Oct 28, 2015 | 2006 Pontiac G6

2 Answers

My truck sonoma gmc 2001 dont past the emission test


Definition of Diagnostic Trouble Code P1345 Audi: Ignition Coil Power Output Stage 3 Short to Ground BMW: Misfire Cylinder 2 with Fuel Cut-Off Buick: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Cadillac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Chevrolet: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Ford: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) GMC: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Isuzu: Crankshaft Position - Camshaft Position Correlation Kia: No SGC Signal (1.6L) Lexus: Variable Valve Timing / CMP Sensor Range / Performance Lincoln: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Mazda: Cylinder Discrimination Signal (from CMP sensor) Mercury: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Oldsmobile: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Pontiac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Saturn: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Toyota: Variable Valve Timing / CMP Sensor Range / Performance Volkswagen: Ignition Coil Power Output Stage 3 Short to Ground

Jul 19, 2015 | GMC Cars & Trucks

2 Answers

Wipers sticking in upright position on 1999 vw passat


It sounds like they are in the "service position" If memory serves correctly do this to get them out of the service position:

Service position To get into service position:
  • After you turn your car off, tap the wiper stalk down. The wipers will move into the service position.
To get out of service position:
  • To move the wipers back, switch on the ignition and tap the wiper stalk down.

Jan 11, 2013 | 1999 Volkswagen Passat

1 Answer

Troubleshoot crank position sensor location


For testing crank sensor,check the help link below:---How to test Crankshaft Position Sensor? http://fordrepairhelp.blogspot.in/2012/03/how-to-test-ford-focus-crankshaft.html
----------

How to test Crankshaft Position CKP Sensor?

---------------
Crankshaft Position Sensor Operation?

----------------
Replace Camshaft position sensor and Crankshaft Position Sensor? http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
----------
GMC Crankshaft Position (CKP) Sensor Replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html

------------
These details will help.
Thanks.

Nov 25, 2012 | 2000 Cadillac Escalade

1 Answer

I have a 93 chevy c3500 that wont shift into high gear I belive it is in the transmission control module but can't locate the box Where is it?


  • GO TO NAPA AND BUY A SENSOR CAPTEUR PART # VSS220 ITS AN THROTTLE MODULE SENSOR, SAME PROBLEM HAPPENED TO ME HOPE IT SOLVES YOUR PROBLEM

Nov 01, 2010 | 1993 Chevrolet C1500

1 Answer

Mon nuisant ne veut pas aacellerer lorse que il


clean MAF sensor with carb cleaner and disconnect battery for 2 hours. drive 10 miles to relearn computer.


go here

http://groups.yahoo.com/group/villagerquest/

Fench guys on team too

Jan 09, 2010 | 1994 Nissan Quest

2 Answers

1997 Chevy Tahoe will crank but will not start.


check the fuse for the injetor. if is bad

Apr 17, 2009 | 2000 Chevrolet Tahoe

1 Answer

1997 mercury sable camshaft sensor replacement


do you have 3.L 2v or 4 valve?

3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder blocks (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (12270) (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder blocks.
Installation
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be used to position the synchronizer assembly prior to installation of the camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs. Locate camshaft position sensor electrical connector in the pre-removal position.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (14-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.

Feb 22, 2009 | 1997 Mercury Sable

Not finding what you are looking for?
2007 Chevrolet Uplander Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...