Question about 2005 Volkswagen Jetta

Open Question

Jetta wont start afeter wiper motor replaced

Changed wiper motor now car wont start.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 89 Answers

SOURCE: steps for replacing wiper motor for 1998 VW Jetta

remove wipers. remove plastic covering by loosening plastic screws first. unplug wiper motor wires. there are about three 10mm nuts at the motor location and you also have to unscrew the big nuts that were below the wipers when you unscrewed them. replacement is reversal.

Posted on Mar 26, 2009

Ad
  • 105 Answers

SOURCE: 2005 jetta wiper motor not working. Washers not

central locking relay its conected to all these could be the culprit

Posted on Dec 17, 2009

steve_e_uk
  • 1675 Answers

SOURCE: 2000 VW jetta VR6 windshield wipers wont work

first try the fues box see if you have a blown fues, next if you put your wipers on can you hear the motor running for them? if you can the linkage has poped off from the motor, its a bit awkward to get it back on and no gaurentee that it will saty on, you might have to replace linkage, or, it might be the cogs on the actual wiper arms have splayed and are now smooth so they dont grip to move, you can take them off by the nut on the arm , get a can (coke can or simular) cut a rectangle out of it the hight and width if the cog, rap it round the cog, (make sure it does not overlap on the ends) and force the arm back into place and then do the nut up, this is just a short quick fix if that is the case you will have to replace the motor, also you can check the relay to the motor in the fues box, give it a tap a couple of times it might work again if not replace it...hope you find these sugestions helpful

Posted on Feb 08, 2010

  • 12 Answers

SOURCE: The winshield wiper on my 2007 Jetta its no

You likely don't need a new motor. You just have to get your wipers repacked with grease.

Posted on Feb 19, 2011

sambo59
  • 74 Answers

SOURCE: 2002 Jetta - Replaced the

Need only adjustment.Open again the plastic covers to rich the viper blade mechanism then loose the nut of the motor and make it in 180degreace.Before that make sure that viper blades are again in the middle of the windscreen.Thats not easy but you can do it.Never happening from first time.

Posted on Jun 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 vw jetta wiper still not working after changing the wiper motor and wiper switch ? help


Did you check the fuse? Have power at the plug? could be a bad ground.

Dec 06, 2015 | Evan Cars & Trucks

1 Answer

2000 jetta wipers wont work


Washer fluid is probably frozen, have you checked the fuse for the wipers? There should be an overload protection in case the blades stick

HTH

Jan 15, 2013 | 2000 Volkswagen Jetta TDI

1 Answer

Just replaced the wiper motor on Jetta and wipers still won't work


Have you replaced only the motor or including the gear box (where the input shaft to the linkages is located)?

Oct 23, 2012 | 1999 Volkswagen Jetta

1 Answer

How to replace wiper motor on 2001 jetta


YOU NEED TO TURN OFF RADIO FIRST THEN DISCONNECT NEGATIVE BATTERY CABLE. YOU NEED TO MARK POSITION OF THE WIPER ARMS ON THE WINDSHIELD YOU CAN USE WHITE OUT LIQUID PAPER TO MARK WIPER ARMS LOCATION.THEN REMOVE WIPER ARMS,REMOVE THE COWL COVER,REMOVE THE WIPER MOTOR LINKAGE MOUNTING BOLTS.REMOVE ASSEMBLY, DISCONNECT THE ELECTRICAL CONNECTOR AND UNBOLT THE MOTOR FROM THE LINKAGE.

Sep 20, 2011 | 2001 Volkswagen Jetta TDI

2 Answers

VW Jetta 4 cylinder, 4 door. Why are the wipers get stuck straight up when i start the car? I push them down to drive.


there is a loose nut to the little electric motor, same thing happened to me or maybe your wiper motor went out if you can hear it moving then its just the loose nut

Apr 27, 2010 | 1999 Volkswagen Jetta

1 Answer

Windshield wipers on 2007 VW jetta not swiping


wiper gears may be broken, got to junk yard and buy motor and gear assembly for windshield wipers, should only take an hour to change out.

Feb 15, 2010 | 2007 Volkswagen Jetta 2.5 Sedan

2 Answers

2000 VW jetta VR6 windshield wipers wont work


first try the fues box see if you have a blown fues, next if you put your wipers on can you hear the motor running for them? if you can the linkage has poped off from the motor, its a bit awkward to get it back on and no gaurentee that it will saty on, you might have to replace linkage, or, it might be the cogs on the actual wiper arms have splayed and are now smooth so they dont grip to move, you can take them off by the nut on the arm , get a can (coke can or simular) cut a rectangle out of it the hight and width if the cog, rap it round the cog, (make sure it does not overlap on the ends) and force the arm back into place and then do the nut up, this is just a short quick fix if that is the case you will have to replace the motor, also you can check the relay to the motor in the fues box, give it a tap a couple of times it might work again if not replace it...hope you find these sugestions helpful

Feb 08, 2010 | 2000 Volkswagen Jetta TDI

1 Answer

The winshield wiper on my 2007 Jetta its no


You likely don't need a new motor. You just have to get your wipers repacked with grease.

Dec 27, 2009 | 2000 Volkswagen Jetta TDI

1 Answer

Wipers wont work wiper motor humms but wipers wont move i can move them with my hand very easy and fuse is ok


tighten the wiper arm nuts vw know for loosenign up. don't wipe ice off or it will happen again

Jun 30, 2009 | 1998 Volkswagen Jetta

2 Answers

Steps for replacing wiper motor for 1998 VW Jetta 4 cyl.


remove wipers. remove plastic covering by loosening plastic screws first. unplug wiper motor wires. there are about three 10mm nuts at the motor location and you also have to unscrew the big nuts that were below the wipers when you unscrewed them. replacement is reversal.

Mar 23, 2009 | 1998 Volkswagen Jetta

Not finding what you are looking for?
2005 Volkswagen Jetta Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...