Question about 2004 Chevrolet Avalanche

2 Answers

Where is the fuse for the drivers power window switch

Posted by Anonymous on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 16 Answers

Watch this video, This will definitely help you.
Video is on this link http://www.carcarekiosk.com/video/2005_Chevrolet_Avalanche_1500_LS_5.3L_V8_FlexFuel/fuse_interior/replace

Posted on Jun 02, 2015

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

If i'm not mistaken it is a 25a silver fuse in the box next to the drivers door. Should say LT Door on the cover.
Also check the DDM 10a fuse.

Posted on Jun 02, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can't find the window fuse for 2003 caddy cts


Check inside trunk under carpet on rear seat back support.

Nov 12, 2016 | Cars & Trucks

1 Answer

How do you remove the right front door panel on a 2004 buick le saber


Did you test it or are you guessing just because it won't open or close ? How To Install Remove Front Door Panel Buick Lesabre 00 05 1AAuto com both right an left are the same .
Power Windows System Components
The following components are used to control the power windows:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Front Door Module (PDM)


?€¢
LH Rear Door Module (LRDM)


?€¢
RH Rear Door Module (RRDM)


?€¢
Driver Door Switch Assembly (DDSA)


?€¢
RH Front Power Window Switch


?€¢
LH Rear Power Window Switch


?€¢
RH Rear Power Window Switch


?€¢
LH Front Power Window Motor


?€¢
RH Front Power Window Motor


?€¢
LH Rear Power Window Motor


?€¢
RH Rear Power Window Motor


?€¢
Class 2 serial data circuit


?€¢
Power door serial data circuit


?€¢
PWR WDO 30 Amp Circuit Breaker


?€¢
DRVMDL Fuse (10 amp)


Driver Door Switch Assembly and Driver Door Module logic, Driver Door Module internal driver operation


?€¢
PASS MDL Fuse (10 amp)


Front Passenger Door Module logic and internal driver operation


?€¢
RRDR MDL Fuse (10 amp)


Left Rear Door Module and Right Rear Door Module logic and internal driver operation


Do you know about computer controlled power windows ?
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.

Oct 30, 2016 | Buick Cars & Trucks

1 Answer

The windows on my crv wont work


at all stations?
all fuses, in both boxes. (did you read the operators guide to find them,
some cars have a circuit break (thermal) for windows,
and is located in the fuse box.
all this info is at alldata.com
ill look. ill respond , as you are a pro DIY person, can read schematics. if not , its just a guessing game.
IT IS a FUSE, not a breaker. but each motor in door has CB.
UNDER HOOD 40am Fuse #13
then fuse 23 underdash and fuse 8 same.
then the relay.same place.
and the relay is controlled by, master station (drivers)
the driver location doesnt need the relay to work.
the relay feeds power to all other window controls
so the master station is unique.
log in to alldata.com and see the pages on power windows.
here are some tid bits.
battery pull warning

Resetting the power window control unit is required after performing the following procedures: Disconnecting the battery, Removing the No. 6 (7.5 A) and/or the No. 23 (20 A) fuses from the under-dash fuse/relay box or disconnecting the driver's door wire harness.
and
window relearn/reset.
Control Unit Reset
  1. Turn the ignition switch ON (II).
  2. Move the driver's window all the way down by holding the driver's switch firmly down; when the window reaches the bottom, hold the driver's window switch firmly down for 2 seconds.
  3. Move the driver's window all the way up by holding the driver's switch firmly up; when the window reaches the top, hold the driver's window switch firmly up for 2 seconds.
  4. If the window does not work in AUTO, turn the ignition switch OFF and repeat the procedure.
  5. Check the window and power door lock operations

Jan 12, 2014 | 2006 Honda CR-V

1 Answer

Both power windows will not close on my 1996 chev tahoe


1. Check power window fuse
2. Check and or replace drivers door power window switch. The passengers power window gets it power through the drivers door switch so if the drivers door switch is out it will take out the passenger window power.

Apr 17, 2011 | Chevrolet Tahoe Cars & Trucks

1 Answer

Is there a power window relay or a re-setable breaker on a toyota t-100. I replaced the master power window switch (drivers side) and still have no power. Where would it be located. I checked all...


When you turn the key on the power flow this way
1 to integration relay ( behind fuse box)
2 integration grab power and give to door control ecu (by the driver compartment fuse box)
3 the ecu gets activated and transfer power from POWER FUSE to power window master switch.
4 Master switch does what you command.

Jan 10, 2011 | Toyota T100 Cars & Trucks

1 Answer

All power windows don't work do I need to get new motors or fuses?


check all fuses and relays first if good check main controll switch on driver door remove passenger door cover remove plug to window switch get a test lite check to see if you have power to pass door window switch have friend move passenger window up and down from main switch on driver door while you check for power on pass window switch plug.if you have no power the main switch on driver could be bad. good luck j.f

Apr 26, 2010 | 1996 Plymouth Voyager

6 Answers

Windows won't roll down


Does the rear window work from the passenger switch?

Oct 07, 2009 | 2003 Cadillac CTS

1 Answer

2003 F250 Power Windows won't work


check fuses 35 & 41 (10 amp, red).
it also shows an accesory delay relay in the fuse panel.
And fuse 601? 30 amp.

make sure you don't have lock-out on driver switch panel activated.

Power Window System
Features and Operation
NOTE: The accessory delay feature will allow power window operation up to 10 minutes after the ignition is off or until a door is opened.
If equipped with power windows, the window control switch (14529):
  • will operate the power windows only when the ignition switch is in the RUN or ACC position.
  • is located on each front door trim panel, and Crew Cab and Excursion rear door trim panel.
  • may be used to raise or lower the driver side, passenger side and rear windows from the LF control on the driver side, or the passenger window from the passenger switch.
  • includes a one-touch down (OTD) feature for the driver door window.
  • can partially lower the driver side window when the LF window control switch is depressed half way (first detent).
  • will completely lower the driver side window when the LF window control switch is fully depressed and then released (second detent).
Power Window System — Modes of Operation
There are two modes of operation for the power window system.
Manual Mode
When the LH window control switch is pressed to the first down position, the window will move down until one of the following conditions are met:
  • The LH window control switch is no longer in the first down position.
  • The LH window control switch is pushed to the OTD position, causing the windows to enter auto mode.
Auto Mode
Auto mode provides the OTD feature. The OTD feature is activated when the LH window control switch, for the LH window, is pressed to the second down position.
Auto mode will be terminated when any of the following conditions are met:
  • The LH window control switch is pushed to the UP position.
  • The LH window control switch is released (OFF position) and then moved to the DOWN position (first detent) or OTD position (second detent).
  • Note: Delayed accessory feature must be active.
The OTD feature is controlled by the window control switch.

---------------------------------------------------------
Condition Possible Sources Action
  • All power windows are inoperative
  • Fuse(s).
  • Circuitry.
  • LF window control switch.
  • Accessory delay relay.

May 23, 2009 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

Possible window fuse blown?


if the fuse is blown none of the windows will work,it sound wierd but all the power to the window motors runs through the drivers side switch. the drivers side switch may be your culprit.to be sure check to see if you have power goin in to the other switches before you replace the drivers side switch.

Jul 31, 2008 | 2002 Toyota Sequoia

1 Answer

Rear wiper


It is the power window relay for feeding power to all the windows except the drivers. If the drivers works the other three don't it is time to replace the power window relay.

Another quick test is to see at each window if the switch works then try it at the driver master switches for each window. If you notice a difference then it is either the power window relay or the master switch.

You can post further feedback based on what you find so I can pinpoint exactly. If all windows are not working then it is the 30a power fuse

Jun 20, 2008 | 1998 Toyota RAV4

Not finding what you are looking for?
2004 Chevrolet Avalanche Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...