Question about 2005 Jeep Liberty

1 Answer

I need to change the tail light on the driver's side of my Jeep Liberty. I got the screws out but cannot get the cover off. What do I do?I tried to pry it off, pull it off, and move it around to get it off, but cannot.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 25 Answers

If you can get to the back side via an access panel for jack or something, you can get to the back bulb sockets. But I do believe there are metal clips that help hold the light assembly in the body as well as the screws.

Posted on Jun 22, 2009

  • LadyPhoenix9 Dec 28, 2010

    You just have to pull hard and shimmy it around. It might be especially hard to get it off if it's never been off before. Good luck!

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace rear brake light 2007 jeep liberty


Open tailgate and use a #20 Torx screwdriver to remove two screws located on the inner side tail light assembly. On the driver's side, the screws are accessable through the tailgate hinge area with the gate open.Pull taillight assembly straight back from the vehicle to get it off. You may need to utilize a wedge to gently work the top and bottom of assembly away from vehicle on outer side. If so, be careful to use plastic wedge or a protective layer (such as a thin piece of cardboard) next to the body to prevent scratching the paint.Once removed, twist applicable light cover counter clockwise and pull to access lightbulb.You may want to apply a small amount of lithium grease to the two plastic stud holes before reinstalling the cover to make it easier to remove the next time.

Mar 05, 2011 | 2007 Jeep Liberty Sport

1 Answer

How do i change the brake light on jeep liberty 2006?


1) You will need to open the rear swing door.

2) On the inside jam there are two torx headed screws (T-15's if I remember correctly).

3) Unscrew the two torx screws.

4) The light is now held by two mounting tabs (small spherical headed plastic sets that go through a rubber grommet).

5) You will need to pry the light casing off (easy pressure with a good size flat head screw driver will do the trick).

6) The light bulbs are twist mount settings inside the light casing.

7) Twist out the mount setting, change the bulbs, and reset the light mountings.

8) To put the light casing push the light casing back on and put in the screws. Everything else will work in reverse when it comes to assembling the whole unit.

2006 Jeep Liberty Replacement Light Bulb Sizes
Low Beam Headlamp Bulb Size: 9007
High Beam Headlamp Bulb Size: 9007
Parking Light Bulb Size: 2825 or 3157
Front Turn Signal Light Bulb Size: 3157
Rear Turn Signal Light Bulb Size: 3757ALL
Tail Light Bulb Size: 3157
Stop Light Bulb Size: 3157
High Mount Stop Light Bulb Size: 921
Fog/Driving Light Bulb Size: 9145 or H3-55W
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 3157
Front Side Marker Light Bulb Size: 168
Ash Tray Light Bulb Size: 161
Map Light Bulb Size: 578
Dome Light Bulb Size: 578
Step/Courtesy Light Bulb Size: 906
Trunk/Cargo Area Light Bulb Size: 578

Thank you for using fixya, and good luck

May 08, 2010 | 2006 Jeep Liberty

1 Answer

Replace tail light 2005 jeep liberty


REPLACING THE BULB IS EASY. OPEN THE LIFT GATE, LOOK TO THE SIDE THAT YOU ARE REPLACING. RIGHT BESIDE THE TAIL LIGHT THE ARE TWO SCREWS. REMOVE THEM AND TAIL LIGHT SHOULD JUST PULL OUT. MAKE SURE TO UNPLUG IT AFTER IT IS LOOSE TO MAKE IT EASIER TO REPLACE THE BULB.

Feb 26, 2010 | 2005 Jeep Liberty

2 Answers

How do i replace tail light bulb on the driver side?


Unscrew the cover, unscrew the bulb, buy a new one, and put it in.

Oct 22, 2009 | 2003 Jeep Liberty

2 Answers

I'm trying to change the brake light on the driver's side of my 06 Jeep Liberty but the rear door is in the way of the screws to remove the tail light assembly. Any solutions?


Open the tailgate all the way. From the inside, use a #25 star bit on a socket wrench with about a 6 or 8 inch extention.

Aug 06, 2009 | 2006 Jeep Liberty

1 Answer

How do I replace a rear brake light on a 2002 jeep liberty sport


Use a #20 Torx screwdriver to remove two screws located on the inner side tail light assembly w/ trunk open.Pull taillight assembly straight back from the vehicle to get it off. You may need to utilize a wedge to gently work the top and bottom of assembly away from vehicle on outer side. If so, be careful to use a protective layer (such as a thin piece of cardboard) next to the body to prevent scratching the paint. A wooden kitchen spatula works with out scratching.Once removed, twist applicable light cover counter clockwise and pull to access lightbulb.You may want to apply a small amount of lithium grease to the two plastic stud holes before reinstalling the cover to make it easier to remove the next time.

Jul 09, 2009 | 2002 Jeep Liberty

1 Answer

Replacing tail light on Jeep Liberty


So you already have the screws out. You simply have to pull it out. It probably have a small plug or *** on the back side to help hold it in place. YOu can pull the unit fairly hard on it with out breaking it, just be firm with it and it should come right out. I'm not sure about the 3rd light, how it is mounted as well. Are you just changing the light bulb in it or changing the cover? If your just changing the bulb or cover you should just be able to take the screws out of the cover and use a small screwdriver to gnetly pry it off.

Apr 28, 2009 | Jeep Liberty Cars & Trucks

2 Answers

Changing brake bulbs


Open the back gate of the jeep. There chould be 2 screws that hold in the light assembly. Remove the screws and pull out the assembly. Replace the bulbs and replave the housing.

Jul 20, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
2005 Jeep Liberty Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...