Question about 2012 Jeep Grand Cherokee

Open Question

How to istall rear door glass - 2012 Jeep Grand Cherokee

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear door glass removal


After you get the regulator assembly out of the way try removing any tracks inside the door that can be removed and see if you can then rotate the glass.

Jan 16, 2014 | 2009 Dodge Journey

1 Answer

Sebring window


Look into window guide clips. These push the glass against the rubber

Oct 28, 2013 | Cars & Trucks

1 Answer

1998 ford explorer rear window removal


Hi there:

  1. Remove the door trim panel and speaker if applicable.
  2. Remove the screw from the division bar. Remove the inside belt weatherstrip(s) if equipped.
  3. Remove the 2 vent window attaching screws from the front edge of the door.
  4. Lower the glass and pull the glass out of the run retainer near the vent window division bar, just enough to allow the removal of the vent window, if equipped.
  5. Push the front edge of the glass downward and remove the rear glass run retainer from the door.
  6. If equipped with retaining rivets, remove them carefully. Otherwise, remove the glass from the channel using Glass and Channel Removal Tool 2900. Remove the glass through the belt opening if possible.

To install:
  1. Install the glass spacer and retainer into the retention holes.
  2. Install the glass into the door, position on the bracket and align the retaining holes.
  3. Carefully install the retaining rivets or equivalent.
  4. Raise the glass to the full closed position.
  5. Install the rear glass run retainer and glass run. Install the inside belt weatherstrip(s).
  6. Check for smooth operation before installing the trim panel.



Hope this helps.

Feb 28, 2013 | 1998 Ford Explorer

1 Answer

Cable system on passenger door power window, 1999 dodge Caravan, has slipped off track. Need exploded diagram to restore to original.


REMOVAL

1. Remove the watershield. (Refer to 23 - BODY/DOOR - FRONT/WATERSHIELD - REMOVAL)

2. Remove door glass retaining clips and secure the window in the up position using masking tape or equivalent(FRONT DOOR GLASS CLIPS).

3. Disconnect wire connector from power window motor, if equipped.

4. Loosen screws attaching front and rear window guide rails to inner door panel (FRONT DOOR MANUAL WINDOW REGULATOR - TYPICAL).

5. Remove screw heads on guide rails from key hole slots in inner door panel.

6. Loosen screws attaching regulator to inner door panel.

7. Remove regulator from inner door panel.

8. Extract rear guide rail through inner door panel rear access hole (FRONT DOOR POWER WINDOW - TYPICAL).

9. Extract front guide rail through front access hole.

INSTALLATION

1. Insert front guide rail through front access hole.

2. Insert rear guide rail through rear access hole.

3. Place window regulator in position on inner door panel.

4. Place screw heads on guide rails in position through key hole slots in inner door panel.

5. Tighten screws to attach front and rear guide rails to inner door panel.

6. Connect wire connector into power window motor, if equipped.

7. Install door glass.

8. Verify door glass alignment and operation.

9. Install sound shield and door trim panel


DIAGRAMS CAN BE FOUND ON JUSTANSWER,COM

Sep 02, 2012 | 1997 Dodge Grand Caravan

1 Answer

The left rear door window fell off the track. How do I remove the door panel to access it.


This is the complete procedure you stop when you see the problem.



1. REMOVE REAR DOOR INSIDE HANDLE BEZEL


(a) Remove the screw.


(b) Using a screwdriver with its tip taped, disengage the 2 claws A.


(c) Pull out the the rear door inside handle bezel in the direction indicated by the arrow, disengage the claw B, and remove the rear door inside handle bezel.


2. REMOVE DOOR PULL HANDLE


(a) Using a screwdriver wrapped with the protective tape, disengage the 2 clips and remove the door pull handle.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


(a) Remove the screw.


(b) Disengage the 7 clips.


(c) Disconnect the connector and pull up on the rear door trim board sub-assembly to remove it.


4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


(a) Remove the bolt.


(b) Disengage the 2 claws and separate the rear door inside handle sub-assembly.


(c) Disconnect the 2 cables and remove the rear door inside handle sub-assembly.


5. REMOVE REAR SPEAKER


6. REMOVE REAR DOOR SERVICE HOLE COVER


(a) Disconnect each connector and remove the rear door service hole cover.


HINT:


Remove the remaining tape on the door side.


7. REMOVE REAR DOOR GLASS RUN


(a) Connect the window regulator switch assembly.


(b) Fully lower the door glass.


(c) Remove the rear door glass run.


8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


(a) Remove the 2 bolts, the screw and rear door window division bar sub-assembly.


9. REMOVE REAR DOOR QUARTER WINDOW GLASS


(a) Pull out the direction indicated by the arrow, remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit.


10. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


(a) Remove the rear door glass sub-assembly as shown in the illustration.


(b) Disconnect the window regulator switch assembly.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


(a) Disconnect the connector.


(b) Loosen the temporary bolt.


NOTICE:


If the temporary bolt is removed, the rear door window regulator may fall and become deformed.


(c) Remove the 3 bolts and the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.


(d) Remove the temporary bolt from the regulator.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


(a) Using a "torx" driver (T25), remove the 3 screws and power window regulator motor assembly rear.


14. REMOVE REAR DOOR LOCK ASSEMBLY


(a) Disconnect the connector.


(b) Remove the bolt.


(c) Using a "torx" socket wrench (T30), remove the 3 screws.


(d) Slide the rear door lock assembly downward, pull out the link from the outside handle frame, and remove the rear door lock assembly and cables as a unit.


(e) Remove the door wire harness packing.


(a) Using a "torx" socket wrench (T30), loosen the screw.


(b) Disengage the 2 claws and remove the rear door outside handle cover.


(a) Disengage the 2 claws and remove the rear door outside handle pad rear.

Jan 03, 2011 | 2006 Toyota Highlander

1 Answer

How do I remove and install a rear passenger side window (manual) in a 1997 Saturn SL1?The window was smashed, and I need to replace it. Thank you so much for your time and help!


Saturn Coupes/Sedans/Wagons 1991-1998 Repair Guide
Door Glass and Regulator - REMOVAL & INSTALLATION
(see Figures 1, 2, 3 and 4)
  1. Remove the outer door panel assembly. Refer to the sub-procedure under Door Locks, earlier in this section.
  2. For rear doors, loosen the bottom fastener of the rear door stationary window assembly, in order to provide clearance, then apply tape to the lower half of the outboard exposed portion of the stationary window channel. The tape must be applied in order to prevent damage to the paint surface.
  3. Lower the door glass, then use SA9148B, or an equivalent tool, to remove the glass nuts. Push the glass upward and rotate slightly, then remove the glass from the vehicle.
  4. If the regulator is also to be removed, proceed as follows:
    1. Remove the inner door trim panel. Refer to the procedure earlier in this section.
    2. If applicable, unplug the wiring harness from the power regulator.
    3. Except for the rear door, remove the regulator cam bolts.
    4. Drill out the regulator rivets and remove the regulator from the vehicle.
To install:
  1. If removed, install the regulator to the door assembly:
    1. Position the regulator to the door and secure using rivets.
    2. Except for the rear door, install the cam bolts.
    3. If applicable, connect the wiring harness to the regulator.
    4. Install the inner door trim panel to the vehicle.
  2. Install the door glass into the door and over the regulator studs.
  3. Install the glass nuts using tool SA9148B, or equivalent.
  4. Check the door glass for proper operation and alignment.
  5. If necessary, adjust the glass alignment. For rear doors, fore/aft adjustments are made after loosening the B bolts, while in/out adjustments are made when the A bolts are loosened.
  6. Except for the rear doors, glass which is not running parallel to the door header may be adjusted after loosening the inner panel cam attachment bolts and adjusting the cam. If the glass is floating in the opening, lower the glass 3 / 4 downward, loosen the front guide fasteners, push the glass rearward to seat it in the rear channel, then bring the front glass guide back to the front edge of the glass. Apply a light finger pressure on the guide and tighten the fasteners.
  7. Once the glass has been properly adjusted and is operating smoothly, install the outer door panel assembly.
cc80642.jpg

Fig. 1: Remove the glass nuts using a suitable tool-front door shown

8ca6a10.jpg

Fig. 2: Exploded view of the regulator mounting-except rear door

b18d064.jpg

Fig. 3: Exploded view of the rear door regulator mounting

0b9470a.jpg

Fig. 4: Adjustments of rear door glass are made after loosening the A or B bolts


I hope help with this (remember rated this help) Good luck.


Oct 16, 2009 | 1997 Saturn SL

1 Answer

How do you replace a drivers side window on a 1992 Saturn



REMOVAL & INSTALLATION

See Figures 1, 2, 3 and 4
  1. Remove the outer door panel assembly. Refer to the sub-procedure under Door Locks, earlier in this section.
  2. For rear doors, loosen the bottom fastener of the rear door stationary window assembly, in order to provide clearance, then apply tape to the lower half of the outboard exposed portion of the stationary window channel. The tape must be applied in order to prevent damage to the paint surface.
  3. Lower the door glass, then use SA9148B, or an equivalent tool, to remove the glass nuts. Push the glass upward and rotate slightly, then remove the glass from the vehicle.
  4. If the regulator is also to be removed, proceed as follows:
    1. Remove the inner door trim panel. Refer to the procedure earlier in this section.
    2. If applicable, unplug the wiring harness from the power regulator.
    3. Except for the rear door, remove the regulator cam bolts.
    4. Drill out the regulator rivets and remove the regulator from the vehicle.


To install:
  1. If removed, install the regulator to the door assembly:
    1. Position the regulator to the door and secure using rivets.
    2. Except for the rear door, install the cam bolts.
    3. If applicable, connect the wiring harness to the regulator.
    4. Install the inner door trim panel to the vehicle.

  2. Install the door glass into the door and over the regulator studs.
  3. Install the glass nuts using tool SA9148B, or equivalent.
  4. Check the door glass for proper operation and alignment.
  5. If necessary, adjust the glass alignment. For rear doors, fore/aft adjustments are made after loosening the B bolts, while in/out adjustments are made when the A bolts are loosened.
  6. Except for the rear doors, glass which is not running parallel to the door header may be adjusted after loosening the inner panel cam attachment bolts and adjusting the cam. If the glass is floating in the opening, lower the glass 3 / 4 downward, loosen the front guide fasteners, push the glass rearward to seat it in the rear channel, then bring the front glass guide back to the front edge of the glass. Apply a light finger pressure on the guide and tighten the fasteners.
  7. Once the glass has been properly adjusted and is operating smoothly, install the outer door panel assembly.

PICTURES ON NEXT POST!

Oct 13, 2009 | 2000 Saturn Ls 4dr Sedan

1 Answer

Need to replace one rear window on 1999 ranger


you can try replacing it your self,some junkyards have used glass thats pretty resonable and some will even istall it for a fee . I

May 31, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Rear Window- Drivers side- won't work


Removal and Installation
  1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the watershield.
  1. Remove the interior weatherstrip.
  1. Remove the exterior-weatherstrip.
  1. Remove the nut and the rear window stabilizer.
  1. syh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removing the rivet center pins, place suitable support between the door outer panel and the glass to stabilize the glass.
    NOTE: Lower the window to access the rivets.
    Remove the two rivets retaining the rear door window glass to the rear door window glass run and bracket.
9eaea6b.gif
  1. Remove the rear door window glass.
  1. To install, reverse the removal procedure.

Apr 09, 2009 | 2000 Ford Taurus

3 Answers

Hey when i push the power botton for the rear window it doesn't go down,I checked the power button,and its good ! Can i replace the power motor in the rear window,and where is it located,i would like to...


  1. Raise and support the rear door window glass to the full up position.
  2. Remove the interior door handle.
  3. Remove the rear door speaker.
  4. Remove the water shield.
  5. Disconnect the rear door window regulator motor electrical connector.
  6. Remove the rear door window regulator rivets.
  7. Remove the rear door window regulator by sliding the regulator arms off of the window glass track.
  8. Installation is the reverse of the removal procedure, noting the following:
    • Cycle the door glass to make sure of engagement of the drive mechanism.
    • Remove the rear door window glass-to-regulator bolt or rivet.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet.
    • Secure the rear door window glass in the full UP position with tape.
    • Disconnect the window regulator motor electrical connector.
    • Remove the 2 window regulator nuts.
    • Remove the 3 window regulator motor bracket nuts.
    • Install the window regulator assembly. Tighten the 3 motor bracket nuts to 89 inch lbs. (10 Nm).
    • Install the 2 window regulator nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
    • Connect the window regulator motor electrical connector.
    • Remove the tape securing the rear door window glass in the full UP position.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet. Tighten the bolt to 62 inch lbs. (7 Nm), or install a new rivet.
    • Install the window regulator motor
    • Remove the window regulator assembly.
Remove the window regulator motor

Feb 23, 2009 | 2001 Ford Explorer

Not finding what you are looking for?
2012 Jeep Grand Cherokee Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...