Question about 1995 Ford Ranger Supercab

1 Answer

How to adjust rear door on o2 ranger supercab

The drivers side door is not hung correctly and rubs on the body. Just looking for some tips before I adjust rear door. Vehicle is a 02 ranger supercab, XLT.
thanks

Posted by on

  • jpatrickdani Jun 22, 2009

    There is no gap at the back (hinge end) and the door is rubbing against the body. So it looks like the hinge needs to be adjusted in the outboard direction. There are 3 hinge bolts attaching the hinge to the body of the truck. The 2 outermost have washers and the one in the middle doesn't. I've loosened the top and bottom hinges but am not sure how to move the door the amount that I'm conncerned that if the hinge bolts are too loose the door will move too much. I've marked the hinges with pencil for ref.

  • paul baker
    paul baker May 11, 2010

    can you tell me which way the door needs to go in detail. top, bottom, front, or rear. Up, down, in, or out?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 70 Answers

Loosen the bolts and insert a body shim, that a local body shop can in most cause give you, behind each bolt and tighten that will kick the door edge away from the body.

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Ranger IAC and PCM problems


i would start looking for vacuum leaks first,

Jun 20, 2012 | 1999 Ford Ranger SuperCab

1 Answer

Having trouble changing Spark plugs on drivers side of 1999 3.0L V6 Ford Ranger. Looking for tips.


Have changed some through fender well. A swivel will be helpfull if you don't have one.

Jun 21, 2011 | 1999 Ford Ranger SuperCab

2 Answers

O2 sencer where are they located


The 02 sensor is located on the exhaust system. It should be a single wire sensor. You will find it between the exhaust manifold and the CAT.

May 21, 2010 | 1991 Ford Ranger Supercab

1 Answer

Rubbing/grinding noise


Usually the strut bearing will make this noise upon turning a corner and hitting a rut or pot hole when turning. A wheel bearing will make a low pitched whinning sound constantly

Jan 16, 2010 | 1998 Ford Ranger SuperCab

1 Answer

!994 ford ranger supercab not getting any fuel, pump was pulled and works


just cause it works does not mean it works correctly, if it has low fuel pressure it wont work correctly, also check the fuel pump cut off switch on the driver side kick panel make sure the button is pushed in and you get power from both wires during cranking if not you will need a switch if only on wire has power

Oct 28, 2009 | 1999 Ford Ranger SuperCab

1 Answer

How do you adjust the parking brake on a 1994 ford ranger,manaul trans,4wd


Start by adjusting up the rear brakes, if those are tight and you still want to tighten up the parking brake running down the driver's side, outside the frame are the parking cables. somewhere around the back of the cab/front of the bed should be a plate with 2 cables and a bolt. tighten the bolt/nut up to make the parking brake tighter

Oct 04, 2009 | 1994 Ford Ranger Supercab

1 Answer

How do i aim the headlights on my 1993 ford ranger xlt 4x4


the adjustment screws are there u just have to look hard for them.
one on bottom up/down one on the side side to side.

Oct 02, 2009 | 1993 Ford Ranger SuperCab

1 Answer

When I push in on my emergency brake is does not activate.


There are two main ways to adjust your brake. 1) adjust bracket on the frame rail (driver's side). 2)adjust rear shoes. check for proper movement of all arms and brackets on rear shoes.

May 21, 2009 | 1995 Ford Ranger Supercab

1 Answer

Where is the #6 engine cylinder on a 1999 ford ranger 3.0


CYLINDER #6 IS DRIVER SIDE REAR.
#1 IS PASS.FRT. 1-2-3 PASSENGER SIDE.
4-5-6 DRIVERS SIDE.

Apr 06, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Ford ranger door ajar switch.


where is the switch located? on the body or the door?
if it is on the body then all what you have to do is remove the screw and disconect it

May 31, 2008 | 1999 Ford Ranger SuperCab

Not finding what you are looking for?
1995 Ford Ranger Supercab Logo

341 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...