Question about 2002 Chrysler PT Cruiser

1 Answer

Were is the air bleed valve for the cooling system on a 2002 pt cruiser

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 6,674 Answers

Usually on or near thermostat housing, but if you can't locate it, leaving rad cap off & heater on & rev engine slightly, once in a while, and wait until rad fan comes on & off 2 or 3 times & you should be good. Top up, install cap, top up bottle.

Posted on Jun 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my 2006 pt cruiser still overheating and bubbling when i replaced the radiator the thermostat and the o2 censor


O2 sensor has nothing to do with engine overheating. Are you losing coolant? Did you bleed all the air out of the cooling system after replacing radiator? Have you checked the coolant for exhaust gas byproducts? You may have a bad head gasket, or a cracked block/head if you ran the car for an extended period while overheated.

Feb 16, 2017 | 2006 Chrysler PT Cruiser

1 Answer

2002 PT Cruiser overheats ONLY when idling, not @ highway speed


sounds like an air pocket in your cooling system need to bleed system and add missing coolant

Jul 07, 2012 | 2002 Chrysler PT Cruiser

1 Answer

Where is the low side valve located on a 2005 pt cruiser for the a/c unit?


360dreamworx_20.gif
The high side valve is located on the filter-drier, and the low side valve is situated on the suction line, near the washer fluid reservoir filler. Good luck and hope you stay cool this summer.

Jul 13, 2011 | 2002 Chrysler PT Cruiser

1 Answer

2003 PT Cruiser . We have tried every thing replaced thermostat + flushed radiator + replaced hoses + checked fan but two days later it over heats when moving in very slow traffic


HAve you check for a bad water pump?.. sometimes even new thermostat are defective too.
Do you know if your car has a relieve valve to bleed the cooling system. If the system has air it will over heat at low RPM's. Sometimes even flushing the radiator wont firx a cooling system with air.
So make sure about these two things I mentioned.
Please dont forget to rate me.

Mar 07, 2011 | Chrysler PT Cruiser Cars & Trucks

1 Answer

I need to change the thermostat


REMOVAL
  1. Remove upper intake manifold.
  2. Partially drain cooling system below the thermostat level.
  3. Remove upper radiator hose from outlet connector.
  4. Remove coolant recovery system hose from outlet connector.
  5. Remove coolant outlet connector bolts.
  6. Remove thermostat assembly, and clean sealing surfaces.
INSTALLATION

25a9b05.gif
  1. Place the new thermostat assembly into the coolant outlet connector, aligning air bleed with the location notch on outlet connector.
  2. Install coolant outlet connector with thermostat in position onto thermostat housing. Tighten bolts to 12.5 Nm (110 inch lbs.).
  3. Install upper radiator hose.
  4. Connect the coolant recovery system hose.
  5. Install upper intake manifold.
  6. Fill cooling system.
  7. see thermostat mounting are below
a4322e5.gif

Oct 19, 2010 | 2002 Chrysler PT Cruiser

1 Answer

My 2001 pt cruiser gurgles when I stop. Have


Ensure coolant system has been properly filled.
Carry out all air bleed operations as specified by the manufacturer- (don't forget to open the heater core supply valve).

Nov 18, 2009 | 2001 Chrysler PT Cruiser

2 Answers

2002 pt cruiser overheating was told i need a new raditor and thermostat for 1 grand sounds fishy


Flush rad & change coolant & thermostat. Check operation of rad fan, & make sure it is coming on when engine reaches normal operating temperature. Be sure to bleed air out good when refilling rad/cooling system. Start engine & turn heater on when refilling & let rad fan come on & off at least 2 or 3 times before putting cap back on rad, and refill rad as needed as you do this. then fill return bottle to proper level & see what happens.

Jun 27, 2009 | 2002 Chrysler PT Cruiser

1 Answer

2000 chrysler pt cruiser


try pumping it for 10 times hold it for 15 seconds then release...... is the master and slave good????? why are you bleeding it???????? leak???? if there was a leak you have a problem bleeding wont fix

Oct 15, 2008 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
2002 Chrysler PT Cruiser Logo

1,130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...