Question about Cars & Trucks

1 Answer

What color is the crank sensor cable in cpu plug

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,679 Answers

What vehicle are you refering to ?

Posted on May 10, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crank position sensor and the ignition module ,coil pack at on a 1998 Pontiac Montana transport


Your spark plug wires go to coils, coils sit on top of ignition module.You have two crank sensors, if crank sensor issue, check the 7x crank sensor, on back side of engine block, down low, two wire connector, wire colors, yellow and purple.
coil pack-byehkl55qszftorfvkdndylg-2-0.jpg

Apr 05, 2017 | Pontiac Montana Cars & Trucks

1 Answer

Where does the crank angle sensor go on a 1990 dodge daytona es turbo and what does it do


crank angle sensor, Crank position sensor ,reads the position in degrees of the crankshaft. When the sensor reads a set point on the crankshaft it sends a signal to the ECM(CPU) program which then triggers the spark for that positioned cylinder. It also triggers the injector to squirt. Without it the CPU will not know when to set the spark or injector so nothing works.It is constant for all ECM controlled engines regardless. Further the cam shaft position sensor sends a signal to the cpu telling it that the valves are in the correct position for spark,fuel. When the cam belt/chain breaks there is no position regestired so the spark and fuel are shut off

Dec 05, 2014 | 1990 Dodge Daytona

1 Answer

Can I advance the timing on a Toyota 2003 4.7v8


The CPU will control the timing advance to keep it correct for rpm's and mixture settings . If you can turn the distributor ( if you do not have individual plug coils ) I feel that the CPU will move it back electronically as it works of the cam/crank position sensors position

Mar 02, 2014 | Cars & Trucks

1 Answer

Cranks not start


use a code reader to reset the CPU as taking the battery lead off all the time corrupts the CPU program

Dec 23, 2013 | Cars & Trucks

1 Answer

2001 jetta vr6 cranks but won't start have fuel and spark replaced camshaft sensor, new plugs valve cover gasket got code of PO343 and PO740


code po740 refers to torque converter clutch(TCC) solenoid-circuit malfunction==causes --wiring--TCC solenoid-ECM/TCM
code p0343 refers to cam shaft position sensor(CMP) A bank1-high input.==causes --wiring short to positive--CMP sensor---ECM. check which cam sensor you replaced and check the wiring connectors. use a code reader to reset the cpu when finished

Sep 06, 2013 | Volkswagen Jetta Cars & Trucks

1 Answer

Ford au 3 replaced crank angle sensor plug - recharged battery as lights were left on and engine will crank but not starty


With a flat battery you will have to have the cpu reset . Use a code reader to do this.

Aug 03, 2013 | Cars & Trucks

1 Answer

1999 Jeep Wrangler 4.0L cranks but will not start. No spark from coil. Replaced coil and crank sensor.


Check all your fuses, check power to your coil, I doubt the crank sensor was bad unless it threw an engine light at you. Ohm out your plug cables.

Apr 13, 2013 | 1999 Jeep Wrangler

1 Answer

1993 jeep wrangler wont start


Your jeep May Have a Blown Head Gasket..That Would Explain The Orange Color On The Plugs.

Mar 31, 2010 | 1993 Jeep Wrangler

1 Answer

1992 Ford Taurus wagon not starting, but turns over


You might have a problem with your crank sensor or ignition. Remove spark plug wire and check for spark while turning engine over. When this happens unplug crank sensor near crank pulley then plug back in to see if it starts if so replace crank sensor.

Jul 29, 2009 | 1992 Ford Taurus

2 Answers

Car wont crank 1994 plymouth acclaim


Not sure what yor experiencing . Do you have crank no start or no crank no start? No crank no start is battery and cables issue. Crank no start is ignition , plugs, and fuel.

May 28, 2009 | 1991 Plymouth Acclaim

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...